Loading Of The Battery; Parts And Functions; Clock Set; Indoor Unit - Haier HSU-12LEA13-M - annexe 3 Operation Manual

Parts and Functions

Parts and Functions

Indoor Unit

1
2
3
7
5
Inlet
1 1
Inlet grille
2 2
Air Purifying Filter (inside)
3 3
Outlet
4 5
Actual inlet grille may vary from the one shown in the
manual according to the product purchased

Display board

8
1 2 3
Singal receiver hole
1
COOL display
2
HEAT display
3
Ambient temp.display
4
When receiving the remote control signal,
display the set temperature and in the rest
time the room temperature is displayed and
this room temperature is only for reference.

Outdoor Unit

OUTLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
INLET 1 4

Clock set

Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
or decrease 1min. If the button is kept pressed,time will
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
MODE SET
TIMER
FAN
CLOCK
SWING
1
Horizontal flap
5 4
(adjust up and down air flow
Don't adjust it manually)
Vertical blade
6 6
(adjust left and right air flow)
Anion generator
7
4 6
5
HEALTH display
5
(If the unit which you purchased
has healthy function,follow it.
If not,please ignore.)
6
Dry display
TIMER OFF display
7
TIMER ON display
SLEEP display
will increase

Remote controller

1
2
A
3
U
T
O
4
5
4 5
ON/OFF
12
6
MODE
8
13
FAN
14
15
SWING
16
SLEEP
(inside)
17
LOCK
18
1. Operation mode display
7
ation mode AUT O
Ope
r
Remote controller
Display board
2. SWING display
3. FAN SPEED display
4. HEALTH display
5. SLEEP display
6. LOCK display
NOTE:
Cooling only unit do not have displays and functions related with heating
If the unit which you purchased has healthy function,follow it.If not,please ignore.

Loading of the battery

3
4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte ries have been used up. Please change batteries.
If the remote controller can't run normally during operation,
please remove the batteries and
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
7. SIGNAL SENDING display
8. TIMER OFF display
9. TIMER ON display
10. CLOCK display
6 11. TEMP display
12. POWER ON/OFF
7
Used for unit start and stop.
8
ON OFF 13. MODE
o
C AM
PM Used to select AUTO run, COOL,
9
HEAT DRY and FAN operation
10
14. FAN
26
Used to select fan speed LO, MED,
TEMP
HI, AUTO
11
(This function is unavailable on
some models.)
19
15. HOUR
SET
Used to set clock and timer setting.
20
16. SWING
Used to set auto fan direction.
TIMER
17. SLEEP
21
Used to select sleep mode.
(This function is unavailable on
CLOCK some models.)
18. LOCK
22
Used to lock buttons and LCD display.
19. TEMP.
HEALTH
POWER/SOFT
25 Used to select your desired temp.
20. SET
24
Used to confirm timer and clock
RESET
settings.
23
21. TIMER
Used to select TIMER ON,
TIMER OFF, TIMER ON-OFF
22. CLOCK
Used to set correct time
COOL DRY HEAT FAN
23. RESET
Used to reset the controller back to
normal condition.
24. HEALTH
Used to operate the healthy function
25. POWER/SOFT button
This function is unavailable on
AUTO LO MED HI some models.
26.
POWER/SOFT
This function is unavailable on
some models.
1
Remove the battery cover;
2
2
Load the batteries as
illustrated. 2 R-03 batteries,
1
resetting key(cylinder);
3
Be sure that the loading
is in line with the " + "/"-";
reload several minutes later.
display