Parts And Functions; Remote Controller; Indoor Unit; Outdoor Unit - Haier HSU-09HEG03/R2(DB) Operation Manual

Parts and Functions

Indoor Unit

EK1 display board
2
4
EK3 display board
2
4
6
1 Inlet
Air Purifying Filter
3
(inside)
5
Horizontal flap
(adjust up and down air flow.
Don't adjust it manually)
Display board
7
Display board
EK1
2
4
6
Signal receiver hole
ON/OFF display
Ambient temp.display
When receiving the remote control
signal,display the set temperature
and in the rest time the room
temperature is displayed and this
room temperature is only for reference.
Please be subject to the actual produce purchased the
above picture is just from your reference

Outdoor Unit

OUTLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
INLET
Please be subject to the actual produce purchased the
above picture is just from your reference
1
1
3
7
6 5
1
3
7
5 8
2 Inlet grille
4 Outlet
6
Vertical blade
(adjust left and right air flow)
Emergency Switch
8
EK3
4
4
TIMER ON/OFF display
TIMER ON-OFF display
SLEEP display
Note to the power failure resume:
Press the sleep button ten times in five seconds and enter function
after hearing four sounds.And press the sleep button ten times
within five seconds and leave this function after hearing two sounds.
5
COOL\HEAT\DRY\AUTO display
6
RUNNING display
4

Remote controller

1
2
8
3
4
5
9
10
11
12
13
14
15
16
17
1. Mode display
Operation mode
AUTO
Remote controller
2. Signal sending display
3. SWING display
4. FAN SPEED display
LO MED HI
5. LOCK display
6. TIMER OFF display
5
TIMER ON display
7.TEMP display
Healthy function is not available for some units.

Loading of the battery

4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
type fluorescent lamp or
room, the recei
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
8. Additional functions display
6
Operation mode
Remote controller
7
9. QUIET button
10. HEAT button
11. COOL button
12. AUTO button
8
13. FAN SPEED button
14. TIMER button
18
15. HEALTH button
16. LOCK button
19
Used to lock buttons and LCD display.
20 17. LIGHT button
Control the lightening and extinguishing
of the indoor LED display board.
21
18. POWER ON/OFF button
19. DRY button
22
20. TEMP button
21. SWING button
23
22. HOUR button
23. EXTRA FUNCTION button
24
Function: Air sending--- Healthy
airflow position1--- Healthy airflow
25
position 2 --- Restore the original
flap position --- Right & left air airflow
--- A-B yard---10 and heating symbol
COOL DRY HEAT FAN
displayed simultaneously--- Sleeping
--- Electrical heating--- Refresh air
(
reserved function)
Fahrenheit/Celsius mode conversion
24.CANCEL/CONFIRM button
Display Function: Setting and cancel to the
circulated
timer and other additional functions.
AUTO
25. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote
1
Remove the battery cover;
2
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
3
Be sure that the loading
is in line with th
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
reload several minutes later.
Supplemented
electrical
QUITE SLEEP HEALTH POWER
heating
--- Power ---
e" + "/"-";