Table of Contents
Advertisement
Parts and Functions
Indoor Unit
Inlet
Inlet grille
Outlet
Vertical blade
(adjust left and
Horizontal flap
right air fl
(adjust up and down air flow
Don't adjust it manually)
1
Display board
1
Signal receiver hole
2
Ambient temp.display
When receiving the remote
control signal, display the set
temperature.
3
COOL display
Inlet
1
1
2
2
Inlet grille
3
3
Outlet
Anion generator
5
4
6
6
(inside)
7
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Display board
1
Remote signal receiver
(A beeping sound is generated when a signal from remote controller isreceived.)
2
Power indicator
(Lights up when unit starts.)
3
Timer mode indicator
(Lights up whenTimer operation is selected.)
4
Operation mode indicator
Ambient temp display
5
When receiving the remote control signal, display the set temperature.
Inlet
1
1
2
2
Inlet grille
3
3
Outlet
Anion generator
5
4
6
6
Vertical blade
(inside)
7
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Power indicator
9
Timer mode indicator
10
(Lights up whenTimer operation is selected.)
Operation mode indicator
11
(lights up when the compressor is on.)
Remote signal receiver
12
(A beeping sound is generated when a signal
from remote controller isreceived.)
Ambient temp display
13
When receiving the remote control signal, display the set
temperature and in the rest time the room temperature is
displayed and this room temperature is only for reference.
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
1
Air Purifying Filter
(inside)
Emergency
Switch
ow)
Display board
2
5
3
4
6
4
HEAT display
5
HEALTH display
6
DRY display
Air Purifying Filter
4
5
(inside)
8
Emergency
Switch
Vertical blade
(adjust left and
Display board
right air fl
ow)
5
1
2
3
4
(lights up when the compressor is on.)
Air Purifying Filter
5
4
(inside)
8
Emergency
Switch
9
10
12
11
(adjust left and
13
right air fl
ow)
(Lights up when unit starts.)
Remote controller
1
2
3
4
5
9
10
11
12
13
14
15
16
17
1. Mode display
Operation mode
AUTO
COOL
DRY
FAN
HEAT
Remote controller
2. Signal sending display
3. SWING display
4. FAN SPEED display
Display
circulated
LO
MED
HI
AUTO
5. LOCK display
6. TIMER OFF display
TIMER ON display
7. TEMP display
NOTE:
Cooling only unit do not have displays and functions related with heating
If the unit which you purchased has healthy function,follow it.If not,please ignore.
Outdoor Unit
Loading of the battery
1
2
3
4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
type fluorescent lamp or
wireless telephone is installed in the
room, the recei
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte
ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
remove the batteries and
8.
Additional functions display
6
Supplemented
electrical
Operation mode
QUIET
SLEEP
heating
7
Remote controller
9. QUIET button
10. HEAT button
8
11. COOL button
12. AUTO button
18
13. FAN SPEED button
14. TIMER button
19
15. HEALTH button
20
16. LOCK button
Used to lock buttons and LCD display
21
17. LIGHT button
Control the lightening and
22
extinguishing of the indoor LED
display board.
23
18. POWER ON/OFF button
24
19. DRY button
20. TEMP button
25
21. SWING button
22. HOUR button
23. EXTRA FUNCTION button
Function: Sleeping---- Healthy
airflow position1--- Healthy airflow
position 2 --- Power ---
Air sending --- A-B yard
24.CANCEL/CONFIRM button
Function: Setting and cancel to the
timer and other additional functions.
25. RESET button
When the remote controller appears
abnormal, use a sharp pointed
article to press this button to reset
the remote.
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL WIRING
4
DRAIN HOSE
4
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
e" + "/"-";
is in line with th
HEALTH
TURBO
Advertisement
Table of Contents
