Parts And Functions; Indoor Unit; Remote Controller; Display Board - Haier AS18NE1LAA Operation Manual

Parts and Functions

Indoor Unit

Inlet
Inlet grille
Outlet
(adjust left and
Horizontal flap
r ight air fl
(adjust up and down air flow
Don't adjust it manually)
1

Display board

1
Signal receiver hole
2
Ambient temp.display
When receiving the remote
control signal, display the set
temperature.
3
COOL display
1 1
2 2 Inlet grille
3 3
Outlet
Anion generator
5 4
(inside)
7
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Display board
1
Remote signal receiver
(A beeping sound is generated when a signal from remote controller isreceived.)
2
Power indicator
(Lights up when unit starts.)
3 Timer mode indicator
(Lights up whenTimer operation is selected.)
4
Operation mode indicator
Ambient temp display
5
When receiving the remote control signal, display the set temperature.
Actual inlet grille may vary from the one shown in the
manual according to the product purchased

Outdoor Unit

1
Air Purifying Filter
(inside)
Vertical blade
Emergency
Switch
ow)
Display board
2
3
4
4
HEAT display
5
HEALTH display
6
DRY display
Inlet 4 5 Air Purifying Filter
(inside)
Vertical blade
6 6
(adjust left and
Display board
r ight air fl ow)
1 2 3 4
(lights up when the compressor is on.)
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL WIRING
4
4 DRAIN HOSE

Remote controller

1
2
3
4
5
9
10
11
12
5
13
6
14
15
16
17
1. Mode display
Operation mode
Remote controller
2. Signal sending display
3. SWING display
4. FAN SPEED display
8
LO MED
Emergency
5. LOCK display
Switch
Healthy function is not available for some units.

Loading of the battery

5
4
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
type fluorescent lamp or
room, the recei
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
ries have been used up. Please change batteries.
batte
If the remote controller can't run normally during operation, please
remove the batteries and
6. TIMER OFF display
6
TIMER ON display
7. TEMP display
7
8. Additional functions display
Operation mode
Remote controller
8
9. TURBO/QUIET button
10.
18
TURBO
/QUIET
11. COOL button
19
12. SWING LEFT/RIGHT button
20
13.
14. HEALTH button
21
SWING
15. SLEEP button
16.
22
17. LIGHT button
SLEEP
HEALTH
23
Control the lightening and extinguishing
TIME
TIME
ON
OFF of the indoor LED display board.
24
18. POWER/SOFT button
25
19. DRY button
20. TEMP button
21.
SWING UP/DOWN button
22. TIME OFF/ON
23.HEALTH AIR FLOW button
AUTO COOL DRY
FAN
24.CANCEL/CONFIRM button
Function: Setting and cancel to the
timer and other additional functions.
25. RESET button
When the remote controller appears
Display
abnormal, use a sharp pointed
circulated
HI AUTO
article to press this button to reset
the remote.
1
Remove the battery cover;
2
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
3
Be sure that the loading
is in line with th
Load the battery,then put on the cover again.
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
reload several minutes later.
Supplemented
electrical
QUIET SLEEP HEALTH TURBO
heating
FAN button
FAN SPEED button
LOCK button
button
e" + "/"-";