Loading Of The Battery - Haier 3U19FS2ERA Service Manual

6.Controller
YR-HD
Remote controller
1
2
3
4
5
9
10
11
12
13
14
15
16
17
. . 1 M o d e d s i l p
Operation mode
AUTO COOL DRY HEAT FAN
Remote controller
. . 2 S g i n a s l e n d n i g d s i l p
3. SWING display
4. FAN SPEED display
Display
circulated
LO MED HI AUTO
5. . LOCK displ
6. TIMER OFF display
TIMER ON display
On the remote control do not have the functions of HEALTH.

Loading of the battery

2
1
3
4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-sta rted type fluorescent lamp or change- over
type fluorescent lamp or wireless telephone is installed in the
room, the recei ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batteries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and reload several minutes later.
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
7. TEMP display
6
8. Additional functions display
Supplemented
electrical
Operation mode
QUITE SLEEP HEALTH
heating
7
Remote controller
. . 9 QUIET but
1 . 0. 0 H E A T b t u
11. 1. COOL but
8
12. 2. AUTO but
18
1 . 3. 3 F A N b t u
14. 4. TIMER but
1 . 5. 5 H E A L T H b t u
19
16. 6. LOCK but
20
Used to lock buttons and LCD display.
17. 7. LIGHT but
21
Control the lightening and extinguishing
of the indoor LED display board.
18. 8. POWER ON/OFF but
22
19. 9. DRY but
23
20. 0. TEMP but
2 . 1. 1 S W N I G b t u
24
2 . 2. 2 H O U R b t u
25 2 . 3. 3 E X T R A F U N C I T O N b
Function: Auto, health airflow
upwards and downwards sending
function,sleep function,
air-refresh(reserved function)
Fahrenheit Celsius conversion
Power setting function
24. CANCEL/CONFIRM button
Function: Setting and cancel to the
timer and other additional functions.
25. 5. RESET but
When the remote controller
appears abnormal, use a sharp
pointed article to press this button
to reset the remote
1
Remove the battery cover;
2
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
3
Be sure that the loading
e" + "/"-";
is in line with th
Super Match
Base Operation
Remote controller
POWER
1. Unit start
Press ON/OFF on the remote controller, unit starts.
2. Select operation mode
COOL button:Cooling mode
HEAT button: Heating mode
DRY button: Dehumidify mode
t u
3.Select temp.setting
Press
Every time the button is pressed, temp.setting
increase 1
rapidly
Every time the button is pressed, temp.setting
decrease 1
decrease rapidly
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed
changes as follows:
Remote controller:
LOW MED
Air conditioner is running under displayed fan speed.
When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
Remote
Operation
Mode
Controller
AUTO
COOL
DRY
HEAT
FAN
135
1
2
3
4
3
button
/
o C,if kept depressed, it will increase
C,if kept depressed, it will
o
Display
circulated
HI
AUTO
Note
Under the mode of auto operation, air conditioner
will automatically select Cool or Heat operation
according to room temperature When FAN is set
to AUTO the air conditioner automatically adjusts
the fan speed according to room temperature.
In DRY mode , when room temperature becomes
lower than temp.setting+2 o C, unit will run
intermittently at LOW speed regardless of FAN
setting.
In HEAT mode, warm air will blow out after a short
period of the time due to cold-draft prevention function.
When FAN is set to AUTO, the air conditioner automatically
adjusts the fan speed according to room temperature.
In FAN operation mode , the unit will not operate in
COOL or HEAT mode but only in FAN mode ,
AUTO is not available in FAN mode. And temp.
setting is disabled. In FAN mode, sleep operation
is not available.