Subscribe to Our Youtube Channel
Related Manuals for IBASE Technology IB200
Summary of Contents for IBASE Technology IB200
- Page 1 IB200 AMD Ryzen™ Embedded R2000 Series 2.5-inch SBC User’s Manual Version 1.0 (May 2024)
- Page 2 Copyright © 2024 IBASE Technology, Inc. All rights reserved. No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
-
Page 3: Compliance
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) IB200 User’s Manual... -
Page 4: Important Safety Information
CAUTION Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point. IB200 User’s Manual... -
Page 5: Warranty Policy
Software in use (such as OS and application software, including the version numbers) If repair service is required, please visit the IBASE’s website to read the warranty and RMA policy, before logging in to the eRMA System. IB200 User’s Manual... -
Page 6: Table Of Contents
Hardware Configuration ........11 Installations ..................12 2.1.1 M.2 Card Installation / Replacement ........12 Setting the Jumpers ................13 Connector Locations on IB200 ............14 Connector Quick Reference .............. 15 2.5.1 Power Switch (SW1) ............16 2.5.2 System Reset (J4) ............... 16 2.5.3... - Page 7 Save & Exit Settings ................58 Appendix ..................59 I/O Port Address Map .......... 錯誤! 尚未定義書籤。 Interrupt Request Lines (IRQ) ......錯誤! 尚未定義書籤。 Watchdog Timer Configuration ......錯誤! 尚未定義書籤。 Onboard Connector Types ........錯誤! 尚未定義書籤。 USB Power Control Bit ......... 錯誤! 尚未定義書籤。 IB200 User’s Manual...
- Page 8 This page is intentionally left blank. IB200 User’s Manual viii...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Specifications • Block Diagram • Product View • Board Dimensions... -
Page 10: Introduction
10Gbps with PDPC support, and three USB 2.0 ports for additional peripheral connections. Storage expansion is facilitated through one M.2 (M-Key, type 2280) slot and one M.2 (E-Key, type 2230) slot, making the IB200 a versatile and efficient choice for a wide range of embedded computing applications. Features ●... -
Page 11: Packing List
Your product package should include the items listed below. If any of the items below is missing, contact the distributor or dealer from whom you have purchased the product. • IB200 Motherboard Optional Accessories IBASE provides optional accessories as listed below. • SATA Cable (SATA-93 2-HD) IB200 User’s Manual... -
Page 12: Specifications
Digital I/O, Watchdog timer Dimensions 100mm x 72mm RoHS Environment • Operating: 0 ~ 60 °C (32 ~ 140 °F) Temperature • Storage: -20 ~ 80 °C (-4 ~ 176 °F) Relative 0 ~ 90%, non-condensing at 60 °C Humidity IB200 User’s Manual... -
Page 13: Block Diagram
General Information Block Diagram IB200 User’s Manual... -
Page 14: Product View
Product View Top / Bottom / I/O View IB200 User’s Manual... - Page 15 General Information IB200 User’s Manual...
- Page 16 I/O View Name USB + RJ45 Stack Connector USB + RJ45 Stack Connector Dual HDMI Port Power Button Switch IB200 User’s Manual...
-
Page 17: Dimensions
General Information Dimensions IB200 User’s Manual... - Page 18 This page is intentionally left blank. IB200 User’s Manual...
-
Page 19: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration This section provides information on jumper settings and connectors on the board in order to set up a workable system. On top of that, you will also need to install crucial pieces such as the CPU and the memory before using the product. -
Page 20: Installations
M.2 Card Installation / Replacement Locate the M.2 slot. Align the key of the M.2 card to the interface, and insert the card slantwise. Push the M.2 card down and fix it with the an M3 screw. IB200 User’s Manual... -
Page 21: Setting The Jumpers
Open When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. IB200 User’s Manual... -
Page 22: Connector Locations On Ib200
Connector Locations on IB200 IB200 User’s Manual... -
Page 23: Connector Quick Reference
M.2 M-Key 2280 Socket USB 2.0 Connector M.2 E-Key 2230 Socket SATA Connector Audio Connector DC Power Input Connector Digital IO Debug Port LCD Backlight Connector CPU Fan Power Connector COM1 & COM2 Ports COM3 & COM4 Ports IB200 User’s Manual... -
Page 24: Power Switch (Sw1)
2.5.1 Power Switch (SW1) 2.5.2 System Reset (J4) Assignment Reset Ground IB200 User’s Manual... -
Page 25: Lvds Connector (J6)
Hardware Configuration 2.5.3 LVDS Connector (J6) Assignment Assignment LVSDE_P LVSDO_P LVSDE_N LVSDO_N LVSCKE_P LVSCKO_P LVSCKE_N LVSCKO_N LVSCE_P LVSCO_N LVSCE_N LVSCO_P LVSBE_P LVSBO_P LVSBE_N LVSBO_N LVSAE_P LVSAO_N LVSAE_N LVSAO_P IB200 User’s Manual... -
Page 26: M-Key 2280 Socket (J7)
2.5.4 M.2 M-Key 2280 Socket (J7) IB200 User’s Manual... -
Page 27: Usb 2.0 Connector (J8)
Hardware Configuration 2.5.5 USB 2.0 Connector (J8) Assignment Assignment Ground Ground VCC5 VCC5 Ground IB200 User’s Manual... -
Page 28: E-Key 2230 Socket (J10)
2.5.6 M.2 E-Key 2230 Socket (J10) IB200 User’s Manual... -
Page 29: Sata Connector (J11)
Hardware Configuration 2.5.7 SATA Connector (J11) Assignment Assignment SATA_TXP0 SATA_TXN0 SATA_RXN0 SATA_RXP0 IB200 User’s Manual... -
Page 30: Audio Connector (J9)
2.5.8 Audio Connector (J9) Assignment LINE _OUT_R LINE _OUT_L JD_FRONT LINE_IN_R LINE_IN_L JD_LINEIN MIC1_R MIC1_L JD_MIC1 IB200 User’s Manual... -
Page 31: Dc Power Input Connector (J12)
Hardware Configuration 2.5.9 DC Power Input Connector (J12) Assignment +12V Ground IB200 User’s Manual... -
Page 32: Digital Io (J14)
2.5.10 Digital IO (J14) Assignment OUT0 OUT1 OUT2 OUT3 IB200 User’s Manual... -
Page 33: Debug Port (J15)
Hardware Configuration 2.5.11 Debug Port (J15) Assignment +3.3V LPC_RST# LPC_FRAME# LPC_AD0 LPC_AD1 LPC_AD2 LPC_AD3 LPC_CLK0 IB200 User’s Manual... -
Page 34: Lcd Backlight Connector (J16)
2.5.12 LCD Backlight Connector (J16) Assignment +12V +12V Backlight Enable Brightness Control IB200 User’s Manual... -
Page 35: Cpu Fan Power Connector (J17)
Hardware Configuration 2.5.13 CPU Fan Power Connector (J17) Assignment Assignment Ground Rotation detection +12V Control IB200 User’s Manual... -
Page 36: Com1 & Com2 Ports (J18)
2.5.14 COM1 & COM2 Ports (J18) Assignment Assignment DCD#1 DCD#2 SIN1 SIN2 SOUT1 SOUT2 DTR#1 DTR#2 DSR#1 DSR#2 RTS#1 RTS#2 CTS#1 CTS#2 RI#1 RI#2 RI#1 RI#2 IB200 User’s Manual... -
Page 37: Com3 & Com4 Ports (J19)
Hardware Configuration 2.5.15 COM3 & COM4 Ports (J19) Assignment Assignment DCD#3 DCD#4 SIN3 SIN4 SOUT3 SOUT4 DTR#3 DTR#4 DSR#3 DSR#4 RTS#3 RTS#4 CTS#3 CTS#4 RI#3 RI#4 RI#3 RI#4 IB200 User’s Manual... - Page 38 This page is intentionally left blank. IB200 User’s Manual...
-
Page 39: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • AMD Ryzen™ R2000 Chipset Drivers • AMD Ryzen™ R2000 Graphics Drivers • Realtek High Definition Audio Driver • Intel LAN Controller Drivers... -
Page 40: Introduction
AMD Ryzen™ R2000 Chipset Drivers Run the driver disc. Click AMD on the left pane and then AMD Ryzen R2000 Drivers on the right pane. Click AMD Ryzen R2000 Chipset Drivers. IB200 User’s Manual... - Page 41 Driver Installation On the following screen (AMD Chipset Software Installer), click Install. After the AMD Chipset Software is installed successfully, click Restart. IB200 User’s Manual...
-
Page 42: Amd Ryzen™ R2000 Graphics Drivers
AMD Ryzen™ R2000 Graphics Drivers Run the driver disc. Click AMD on the left pane and then AMD Ryzen R2000 Drivers on the right pane. Click AMD Ryzen R2000 Graphics Drivers. IB200 User’s Manual... - Page 43 Driver Installation On the following screen (AMD Radeon PRO Software Installer), click Install. To complete the installation process, click Restart. IB200 User’s Manual...
-
Page 44: Realtek High Definition Audio Driver
Realtek High Definition Audio Driver Run the driver disc. Click AMD on the left pane and then AMD Ryzen R2000 Drivers on the right pane. Click Realtek High Definition Audio Driver. IB200 User’s Manual... - Page 45 On the Welcome screen to the InstallShieldWizard for the audio driver, click Next to continue. The next screen describes the setup options. Click Next. When the InstallShield Wizard has completed the audio driver installation, you must restart your computer. IB200 User’s Manual...
-
Page 46: Intel Lan Controller Drivers
Intel LAN Controller Drivers Run the driver disc. Click LAN Card on the left pane and then Intel LAN Controller Drivers on the right pane. Click Intel(R) I21x / I22x Gigabit Network Drivers. IB200 User’s Manual... - Page 47 Driver Installation On the next screen, click Install Drivers and Software to continue. On the Welcome screen to the Install wizard for the Intel® Network Connections, click Next. IB200 User’s Manual...
- Page 48 Select the program features to be installed in the Setup Options and click Next. On the following screeen (Ready to Install the Program), click Install to begin the installation. On the next screen (Install wizard Completed), click Finish. IB200 User’s Manual...
-
Page 49: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Boot Settings •... -
Page 50: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. IB200 User’s Manual... -
Page 51: Main Settings
Set the time. Use the <Tab> key to switch System Time between the time elements. 4.4 Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. IB200 User’s Manual... - Page 52 TPM 1.2 will restrict support to TPM 1.2 devices. TPM 2.0 will restrict support to TPM 2.0 devices. Device Select Auto will support both with the default set to TPM 2.0 devices. If not found, TPM 1.2 devices will be enumerated. IB200 User’s Manual...
- Page 53 OS. ACPI Sleep State Selects an ACPI sleep state where the system will enter when the Suspend button is pressed. 4.4.3 IDE Configuration BIOS Setting Description SATA Ports Detects the connection of SATA0 and SATA1. IB200 User’s Manual...
- Page 54 4.4.4 LVDS Configuration BIOS Setting Description LVDS Control Options: Enable or Disable LVDS Backlight Options: 0(Min), 1, 2, 3, 4, 5, 6, 7 (Max) Control IB200 User’s Manual...
- Page 55 BIOS Setup 4.4.5 F81966 Super IO Configuration BIOS Setting Description Sets parameters of Serial Ports. Serial Ports Enables / Disables the serial port and Configuration select an optimal setting for the Super IO device. Serial Port 1~4 Configuration IB200 User’s Manual...
- Page 56 Options: Disabled, 50C, 60C, 70C, 80C Control These fields are the parameters of the hardware Temperatures / monitoring function feature of the motherboard. Voltages The values are read-only values as monitored by the system and show the PC health status. IB200 User’s Manual...
- Page 57 BIOS Setup 4.4.7 CPU Configuration BIOS Setting Description Node 0 Information Displays the memory information related to Node 0. IB200 User’s Manual...
- Page 58 4.4.8 AMI Graphic Output Protocol Policy BIOS Setting Description Output Select Allows you to select an output interface. IB200 User’s Manual...
- Page 59 Host Controller. Device power-up Auto uses default value for a Root port it is delay 100ms. But for a Hub port, the delay is taken from Hub descriptor. Options: Auto / Manual IB200 User’s Manual...
- Page 60 If disabled, Ipv4 HTTP boot option will not be available. PXE boot wait Assigns a period of time to press ESC key to abort the time PXE boot. Media detect Assigns a number of times to check the presence of count media. 4.4.11 CSM Configuration IB200 User’s Manual...
- Page 61 BIOS Setup 4.4.12 NVMe Configuration 4.4.13 AMD CBS IB200 User’s Manual...
-
Page 62: Chipset Settings
4.5 Chipset Settings 4.5.1 SB USB Configuration BIOS Setting Description SB USB Options for SB USB Configuration. Configuration 4.5.1.1. XHCI Ports BIOS Setting Description XHCI 0 & XHCI 1 Enables / Disables the XHCI0 & XHCI1 ports Ports (XHCI/EMCI). IB200 User’s Manual... -
Page 63: Security Settings
BIOS Setup 4.6 Security Settings BIOS Setting Description Administrator Sets an administrator password for the setup Password utility. User Password Sets a user password. IB200 User’s Manual... - Page 64 Force System to User Mode. Install factory Restore Factory Keys default Secure Boot key databases. Reset To Setup Delete all Secure Boot key databases from Mode NVRAM Enables expert users to modify Secure Boot Key Management Policy variables without full authentication IB200 User’s Manual...
-
Page 65: Boot Settings
Enables / Disables Quiet Boot option. Boot mode select Selects a Boot mode, Legacy / UEFI. Boot Option Priorities Sets the system boot order. UEFI USB Key Drive Specifies the Bood Device Priority sequence BBS Priorities from available UEFI USB Key Drives. IB200 User’s Manual... -
Page 66: Save & Exit Settings
Restores / Loads defaults values for all the Restore Defaults setup options. Save as User Saves the changes done so far as User Defaults Defaults. Restore User Restores the user defaults to all the setup Defaults options. IB200 User’s Manual... -
Page 67: Appendix
Appendix This section provides the mapping addresses of peripheral devices, the sample code of watchdog timer configuration, and types of onboard connectors. - Page 68 IB200 User’s Manual...
Need help?
Do you have a question about the IB200 and is the answer not in the manual?
Questions and answers