Related Manuals for IBASE Technology IB918F
Summary of Contents for IBASE Technology IB918F
- Page 1 IB918F AMD Ryzen™ Embedded V1000/R1000 3.5” Disk-Size SBC User’s Manual Version 1.0...
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
- Page 3 0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) IB918F User’s Manual...
-
Page 4: Important Safety Information
CAUTION Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point. IB918F User’s Manual... -
Page 5: Warranty Policy
Software in use (such as OS and application software, including the version numbers) If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. IB918F User’s Manual... -
Page 6: Table Of Contents
Hardware Configuration ........11 Installations ..................12 2.1.1 Installing the Memory ............12 Setting the Jumpers ................13 Jumper & Connector Locations on IB918F ........14 Jumpers Quick Reference ..............15 2.4.1 LCD Panel Power Selection (JP2) ........15 2.4.2 PWM Backlight Control Level (JP3) ........ - Page 7 Advanced Settings ................47 Chipset Settings .................57 Security Settings ................58 Boot Settings ..................59 Save & Exit ..................60 Appendix ..................61 I/O Port Address Map ................62 Interrupt Request Lines (IRQ) ............65 Watchdog Timer Configuration ............68 Onboard Connector Types ..............73 IB918F User’s Manual...
- Page 8 This page is intentionally left blank. viii IB918F User’s Manual...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Specifications • Block Diagram • Board Pictures • Board Dimensions... -
Page 10: Introduction
2x DDR4 SO-DIMM expandable up to 32 GB, ECC supported • 2x PCIe Gigabit Ethernet • 2x HDMI (2.0a), 1x 24-bit dual channel LVDS, 1x eDP • 4x USB3.1, 1 x SATA III, 4x COM • 1x M.2 M-Key Type:2280, 1x M.2 E-Key Type:2230 IB918F User’s Manual... -
Page 11: Packing List
Disk (including chipset drivers) • This User’s Manual Optional Accessories IBASE provides the following optional accessories: • Cable Kit (IB90) for IB918F-1605 / IB918F-1202 SATA cable (SATA-53A) Power cable (PW87) COM ports cable (PK1H) USB cable (USB-168) • Cable Kit(IB91) for IB918F-1606G / IB918F-1505G... -
Page 12: Specifications
2 x HDMI 2.0a (3840 x 2160 at 60Hz) • 1 x eDP (1920 x 1080 at 60Hz) Display • 1 x 24-bit dual channel LVDS (1920 x 1080 at 60Hz) V1000 only 2 x RJ45 GbE LAN IB918F User’s Manual... - Page 13 Operation: 0 ~ 60 °C (32 ~ 140 °F) Temperature • Storage: -20 ~ 80 °C (-4 ~ 176 °F) Relative 0 ~ 90 %, non-condensing at 60 °C Humidity All specifications are subject to change without prior notice. IB918F User’s Manual...
-
Page 14: Block Diagram
Block Diagram IB918F User’s Manual... -
Page 15: Board Pictures
General Information Board Pictures Top and bottom View ＊The photos above are for reference only. Some minor components may differ. IB918F User’s Manual... - Page 16 I/O View Name COM1 Port (CN2) Dual GbE LAN Ports (CN3) HDMI Port (CN4) HDMI Port (CN5) USB 3.1 Ports (CN6) USB 3.1 Ports (CN7) IB918F User’s Manual...
-
Page 17: Dimensions
General Information Dimensions IB918F User’s Manual... - Page 18 This page is intentionally left blank. IB918F User’s Manual...
-
Page 19: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration This section provides information on jumper settings and connectors on the board in order to set up a workable system. The topics covered are: • Installations: Memory • Jumper and connector locations • Jumper settings and information of connectors... -
Page 20: Installations
Gently push the module in an upright position until the clips of the slot close to hold the module in place when the module touches the bottom of the slot. To remove the module, press the clips outwards with both hands, and the module will pop-up. IB918F User’s Manual... -
Page 21: Setting The Jumpers
1 2 3 When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. IB918F User’s Manual... -
Page 22: Jumper & Connector Locations On Ib918F
Jumper & Connector Locations on IB918F IB918F User’s Manual... -
Page 23: Jumpers Quick Reference
Jumpers Quick Reference Function Jumper Page LCD Panel Power Selection PWM Backlight Control Level eDP Panel Power Selection ATX / AT Power Selection Clear CMOS Data 2.4.1 LCD Panel Power Selection (JP2) Function Pin closed Illustration 3.3V (default) IB918F User’s Manual... -
Page 24: Pwm Backlight Control Level (Jp3)
2.4.2 PWM Backlight Control Level (JP3) Function Pin closed Illustration 3.3V (default) 2.4.3 eDP Panel Power Selection (JP1) Function Pin closed Illustration 3.3V (default) IB918F User’s Manual... -
Page 25: Atx / At Power Selection (Jp5)
Hardware Configuration 2.4.4 ATX / AT Power Selection (JP5) Function Pin closed Illustration ATX Mode AT Mode IB918F User’s Manual... -
Page 26: Clear Cmos Data (Jp4)
2.4.5 Clear CMOS Data (JP4) Function Pin closed Illustration Normal (default) Clear CMOS IB918F User’s Manual... -
Page 27: Connectors Quick Reference
SATA1 Dual USB 3.1 Ports CN6, CN7 Dual GbE LAN Port HDMI Ports CN4, CN5 M.2 E2230 Slot M.2 M2280 Slot USB 3.1 Ports USB 2.0 Ports DDR4 SO-DIMM Slot J4, J7 Factory Use Only J9, J17 IB918F User’s Manual... -
Page 28: Edp Connector (Cn1)
+3.3V (default) / +5V Ground +3.3V (default) / +5V AUXP +3.3V (default) / +5V AUXN Ground Ground VCC3 Ground VCC12 Ground HOT PLUG Ground Ground VCC5 Brightness Ground BKLT_EN VCC12 VCC3 Ground Ground TXN1 SMB_CLK TXP1 SMB_DATA Ground IB918F User’s Manual... -
Page 29: Com2 (J18) & Com3 (J16) & Com4 (J15) Rs-232 Ports
COM2 (J18) & COM3 (J16) & COM4 (J15) RS-232 Ports Signal Signal DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready Ground DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator Not Used IB918F User’s Manual... -
Page 30: Com1 Rs-232/422/485 Ports (Cn2)
DCD, Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator Ground Signal Name RS-232 RS-422 RS-485 Data- Data+ Ground Ground Ground IB918F User’s Manual... -
Page 31: Dc-In Power Connector (J14)
Hardware Configuration 2.5.4 DC-In Power Connector (J14) Signal Signal +12V ~ +24V Ground 2.5.5 LCD Backlight Connector (J6) Signal Signal +12V Brightness Control Backlight Enable Ground IB918F User’s Manual... -
Page 32: Lvds Connector (J3, J5)
2.5.6 LVDS Connector (J3, J5) Signal Signal Name TX0+ TX0- Ground Ground TX1+ TX1- Ground Ground TX2+ TX2- Ground Ground TXC+ TXC- Ground Ground TX3+ TX3- +3.3 / +5V +3.3 / +5V IB918F User’s Manual... -
Page 33: Sata Power Connector (J13)
Hardware Configuration 2.5.7 SATA Power Connector (J13) Signal Signal Ground Ground +12V 2.5.8 Digital I/O Connector (J19) Signal Signal Ground OUT3 OUT1 OUT2 OUT0 IB918F User’s Manual... -
Page 34: Front Panel Settings Connector (J12)
Orientation is not required when making a connection to this header. • Power LED (Pins 7 and 8) This connector connects to the system power LED on control panel. This LED will light when the system turns on. IB918F User’s Manual... -
Page 35: Speaker Connector (J2)
Hardware Configuration 2.5.10 Speaker Connector (J2) Signal Signal Speaker-L+ Speaker-R- Speaker-L- Speaker-R+ IB918F User’s Manual... -
Page 36: Audio Connector (J1)
2.5.11 Audio Connector (J1) Signal Signal Lineout_L Lineout_R JD_FRONT Ground LINEIN_L Linein_R JD_LINEIN Ground MIC_L MIC-R JD_MIC1 Ground IB918F User’s Manual... -
Page 37: Fan Power Connectors (Cpu_Fan1)
Hardware Configuration 2.5.12 Fan Power Connectors (CPU_FAN1) CPU_FAN1: CPU fan power connector Signal Name Signal Name Ground Rotation detection +12V Control 2.5.13 SATA III Connector (SATA1) IB918F User’s Manual... -
Page 38: Dual Gbe Lan Port (Cn3)
2.5.14 Dual GbE LAN Port (CN3) 2.5.15 HDMI Ports (CN4, CN5) 2.5.16 Dual USB 3.1 Ports (CN6, CN7) Remarks: For the IB918F R1000 version, CN7 will not achieve the USB 3.1 Gen 2 transfer speed. IB918F User’s Manual... -
Page 39: E Key) 2230 Slot (J8)
Hardware Configuration 2.5.17 M.2 (E key) 2230 Slot (J8) 2.5.18 M.2 (M key) 2280 Slot (J11) IB918F User’s Manual... -
Page 40: Usb 3.1 /2.0 Ports (J10)
2.5.19 USB 3.1 /2.0 Ports (J10) USB 3.1: via an on-board pin headers (V1000 only) USB 2.0: via an on-board pin headers (R1000 only) Signal Signal VCC5 Ground VCC5 Ground Ground Ground IB918F User’s Manual... -
Page 41: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • AMD Ryzen™ V1000/R1000 Graphics Driver • HD Audio Driver • LAN Driver... -
Page 42: Introduction
The contents of this section include the following: AMD Ryzen™ V1000 Graphics Drivers Insert the disk enclosed in the package. Click AMD on the left pane and then AMD Ryzen V1000 Drivers on the right pane. Click AMD Ryzen V1000 Graphics Drivers. IB918F User’s Manual... - Page 43 Driver Installation Now click Accept and Install to proceed. Choose and click on either Express Install or Custom Install. When the software driver has been installed, restart the computer for changes to take effect. IB918F User’s Manual...
-
Page 44: Amd Ryzen™ R1000 Graphics Drivers
AMD Ryzen™ R1000 Graphics Drivers Insert the disk enclosed in the package. Click AMD on the left pane and then AMD Ryzen R1000 Drivers on the right pane. Click AMD Ryzen R1000 Graphics Drivers. IB918F User’s Manual... - Page 45 Read the software license agreement and click Accept and Install to proceed. Choose and click on either Express Install or Custom Install. When the software driver has been installed, restart the computer for changes to take effect. IB918F User’s Manual...
-
Page 46: Hd Audio Driver Installation
Realtek High Definition Audio Driver on the right pane. On the Welcome screen of the InstallShield Wizard, click Next. Follow the steps accordingly. When Setup has successfully installed the Audio Driver, restart your computer for changes to take effect. IB918F User’s Manual... -
Page 47: Lan Driver Installation
Driver Installation LAN Driver Installation Insert the disk enclosed in the package. Click LAN Card on the left pane and Intel LAN Controller Drivers on the right pane. Click Intel(R) I21x Gigabit Networks Drivers. IB918F User’s Manual... - Page 48 When the Welcome screen appears, click Next. Choose “I accept the terms in the license agreement” and click Next. Click Next after selecting the program features as shown below. IB918F User’s Manual...
- Page 49 Driver Installation On the next screen, click Install to install the program. When the wizard has successfully installed the Program, restart your computer for changes to take effect. IB918F User’s Manual...
-
Page 50: Observer
Insert the disk enclosed in the package with the board. Click Tools on the left pane and then Observer on the right pane. Click Next when the Welcome screen appears and to continue installing the Observer on your computer. IB918F User’s Manual... - Page 51 Driver Installation The next screen shows the destination location where Observer will be installed. Click Next. Setup is now ready to begin installing Observer on your computer. Click Install. IB918F User’s Manual...
- Page 52 To complete the installation of Observer, Setup must restart your computer. Restart the computer (click Finish) for changes to take effect. IB918F User’s Manual...
-
Page 53: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Boot Settings •... -
Page 54: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. IB918F User’s Manual... -
Page 55: Main Settings
Set the time. Use the <Tab> key to switch System Time between the data elements. 4.4 Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. IB918F User’s Manual... - Page 56 TPM 1.2 will restrict support to TPM 1.2 deevices. TPM 2.0 will restrict support to TPM Device Select 2.0 devices. Auto will support both with the default set to TPM 2.0 devices if not found. TPM 1.2 devices will be enumerated. (Default: Auto) IB918F User’s Manual...
-
Page 57: Ide Configuration
Selects an ACPI sleep state where the system ACPI Sleep State will enter when the Suspend button is pressed. (Default: S3 (Suspend to RAM) 4.4.3 IDE Configuration BIOS Setting Description SATA Ports Detects the connection of SATA0 and SATA1. IB918F User’s Manual... - Page 58 4. LVDS Backlight Control: 0(Min), 1, 2, 3, 4, 5, 6, 7(Max 4.4.5 F81964 Super IO Configuration BIOS Setting Description Serial Port 1/2/3/4 Set parameters of Serial Port 1/2/3/4 Configuration [Enable] Provide the standby power for devices. Standby Power on S5(EuP) [Disable] Shutdown the standby power. IB918F User’s Manual...
- Page 59 BIOS Setup IB918F User’s Manual...
- Page 60 Enables / Disables the CPU smart fan feature. Control Temperatures / Fan The values are read-only values as monitored by Speed / Voltages the system and show the PC health status. CPU Shutdown Enables / Disables the CPU shutdown Temperature temperature function. IB918F User’s Manual...
- Page 61 BIOS Setup 4.4.7 CPU Configuration BIOS Setting Description Node 0 Information Displays the memory information related to Node 0. 4.4.8 AMI Graphic Output Protocol Policy BIOS Setting Description Output Select Allows you to select an output interface. IB918F User’s Manual...
- Page 62 Host Controller. Device power-up Auto uses default value for a Root port it is delay 100ms. But for a Hub port, the delay is taken from Hub descriptor. Options: Auto / Manual IB918F User’s Manual...
- Page 63 Enables / Disables CSM support. Controls the execution of UEFI and Legacy PXE OpROM. Network Options: Do not launch UEFI / Legacy 4.4.11 NVMe Configuration 4.4.12 Network Stack Configuration BIOS Setting Description Network Stack Enables / Disables UEFI Network Stack. IB918F User’s Manual...
- Page 64 BIOS Setting Description This is for the NB configuration for IOMMU NB Common Options settings and system configuration. FCH Common Here you can set the AC loss control method with options of: Always Off / Always On Options IB918F User’s Manual...
-
Page 65: Chipset Settings
4.5 Chipset Settings 4.5.1 SB USB Configuration BIOS Setting Description SB USB Configuration Options for SB USB Configuration. 4.5.1.1. XHCI Ports BIOS Setting Description Enables / Disables the XHCI0 & XHCI1 ports XHCI0 & XHCI1 Ports (XHCI/EMCI). IB918F User’s Manual... -
Page 66: Security Settings
Secure Boot feature is Active if Secure Boot is enabled. Platform Key (PK) is enrolled and the Secure Boot system is in user mode. The mode change requires platform reset. IB918F User’s Manual... -
Page 67: Boot Settings
65535(0xFFFF) means indefinite waiting. Bootup NumLock Selects the keyboard NumLock state. State Quiet Boot Enables / Disables Quiet Boot option. Boot mode select Selects a Boot mode, Legacy / UEFI. Boot Option Priorities Sets the system boot order. IB918F User’s Manual... -
Page 68: Save & Exit
Restores / Loads defaults values for all the setup Restore Defaults options. Save as User Defaults Saves the changes done so far as User Defaults. Restores the user defaults to all the setup Restore User Defaults options. IB918F User’s Manual... -
Page 69: Appendix
Appendix This section provides the mapping addresses of peripheral devices, the sample code of watchdog timer configuration, and types of on-board connectors. -
Page 70: I/O Port Address Map
PCI Express Root Complex 0x00000000-0x000003AF Direct memory access controller 0x000003E0-0x00000CF7 PCI Express Root Complex 0x000003B0-0x000003DF PCI Express Root Complex 0x00000D00-0x0000FFFF PCI Express Root Complex 0x0000F000-0x0000FFFF PCI Express Root Port 0x0000E000-0x0000EFFF PCI Express Root Port 0x00000040-0x00000043 System timer 0x00000010-0x0000001F Motherboard resources IB918F User’s Manual... - Page 71 Motherboard resources 0x00000C50-0x00000C51 Motherboard resources 0x00000C52-0x00000C52 Motherboard resources 0x00000C6C-0x00000C6C Motherboard resources 0x00000C6F-0x00000C6F Motherboard resources 0x00000CD0-0x00000CD1 Motherboard resources 0x00000CD2-0x00000CD3 Motherboard resources 0x00000CD4-0x00000CD5 Motherboard resources 0x00000CD6-0x00000CD7 Motherboard resources 0x00000CD8-0x00000CDF Motherboard resources 0x00000800-0x0000089F Motherboard resources 0x00000B00-0x00000B0F Motherboard resources 0x00000B20-0x00000B3F Motherboard resources IB918F User’s Manual...
- Page 72 Address Device Description 0x00000900-0x0000090F Motherboard resources 0x00000910-0x0000091F Motherboard resources 0x00000061-0x00000061 System speaker 0x00000081-0x00000083 Direct memory access controller 0x00000087-0x00000087 Direct memory access controller 0x00000089-0x0000008B Direct memory access controller 0x0000008F-0x0000008F Direct memory access controller 0x000000C0-0x000000DF Direct memory access controller IB918F User’s Manual...
-
Page 73: Interrupt Request Lines (Irq)
1.10 (Microsoft) IRQ 4 Communications Port (COM1) IRQ 3 Communications Port (COM2) IRQ 5 Communications Port (COM3) IRQ 5 Communications Port (COM4) IRQ 6 Communications Port (COM5) IRQ 6 Communications Port (COM6) IRQ 53 High Definition Audio Controller IB918F User’s Manual... - Page 74 AMD USB 3.10 eXtensible Host Controller - 1.10 (Microsoft) IRQ 4294967258 AMD USB 3.10 eXtensible Host Controller - 1.10 (Microsoft) IRQ 4294967257 AMD USB 3.10 eXtensible Host Controller - 1.10 (Microsoft) IRQ 4294967287 Intel(R) I211 Gigabit Network Connection IB918F User’s Manual...
- Page 75 Intel(R) I211 Gigabit Network Connection IRQ 4294967278 Intel(R) I211 Gigabit Network Connection IRQ 4294967277 Intel(R) I211 Gigabit Network Connection IRQ 4294967276 Intel(R) I211 Gigabit Network Connection IRQ 4294967289 AMD PSP 10.0 Device IRQ 4294967288 AMD PSP 10.0 Device IB918F User’s Manual...
-
Page 76: Watchdog Timer Configuration
(NCT6116D_BASE) #define NCT6116D_DATA_PORT (NCT6116D_BASE+1) //--------------------------------------------------------------------------- #define NCT6116D_REG_LD 0x07 //--------------------------------------------------------------------------- #define NCT6116D_UNLOCK 0x87 #define NCT6116D_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_NCT6116D(void); void Set_NCT6116D_LD( unsigned char); void Set_NCT6116D_Reg( unsigned char, unsigned char); unsigned char Get_NCT6116D_Reg( unsigned char); //--------------------------------------------------------------------------- #endif //__NCT6116D_H IB918F User’s Manual... - Page 77 (SIO == 0) printf("Can not detect Nuvoton NCT6116D, program abort.\n"); return(1); WDTInitial(); WDTEnable(10); WDTDisable(); return 0; //--------------------------------------------------------------------------- void WDTInitial(void) unsigned char bBuf; Set_NCT6116D_LD(0x08); //switch to logic device 8 bBuf = Get_NCT6116D_Reg(0x30); bBuf &= (~0x01); Set_NCT6116D_Reg(0x30, bBuf); //Enable WDTO //--------------------------------------------------------------------------- IB918F User’s Manual...
- Page 78 //enable timer bBuf = Get_NCT6116D_Reg(0xF0); bBuf &= (~0x08); Set_NCT6116D_Reg(0xF0, bBuf); //count mode is second Set_NCT6116D_Reg(0xF1, NewInterval); //set timer //--------------------------------------------------------------------------- void WDTDisable(void) Set_NCT6116D_LD(0x08); //switch to logic device 8 Set_NCT6116D_Reg(0xF1, 0x00); //clear watchdog timer Set_NCT6116D_Reg(0x30, 0x00); //watchdog disabled //--------------------------------------------------------------------------- IB918F User’s Manual...
- Page 79 //NCT6116D?? goto Init_Finish; NCT6116D_BASE = 0x2E; result = NCT6116D_BASE; ucDid = Get_NCT6116D_Reg(0x20); if (ucDid == 0xC4) //NCT6116D?? goto Init_Finish; NCT6116D_BASE = 0x00; result = NCT6116D_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_NCT6116D (void) outportb(NCT6116D_INDEX_PORT, NCT6116D_UNLOCK); outportb(NCT6116D_INDEX_PORT, NCT6116D_UNLOCK); //--------------------------------------------------------------------------- IB918F User’s Manual...
- Page 80 LD); Lock_NCT6116D(); //--------------------------------------------------------------------------- void Set_NCT6116D_Reg( unsigned char REG, unsigned char DATA) Unlock_NCT6116D(); outportb(NCT6116D_INDEX_PORT, REG); outportb(NCT6116D_DATA_PORT, DATA); Lock_NCT6116D(); //--------------------------------------------------------------------------- unsigned char Get_NCT6116D_Reg(unsigned char REG) unsigned char Result; Unlock_NCT6116D(); outportb(NCT6116D_INDEX_PORT, REG); Result = inportb(NCT6116D_DATA_PORT); Lock_NCT6116D(); return Result; //----------------------------------------------------------------------- IB918F User’s Manual...
-
Page 81: Onboard Connector Types
Hao Guo Xing Ye COM6 RS-232 J18, J16 DF11-10S-PA66H DF11-10DS-2C Port Speaker Connector B4B-PH-K-S PHR-4 E-Call Dupont Audio 0126-01-2821009 10P 2.54 mm-pitch Connector (female) TechBest Molex CPU_FAN1 W2-03I104132S1WT(A)-L 47054-1000 Fan Power Connectors SYS_FAN1, E-Call Molex SYS_FAN2 0110-02-111-030 22-01-2031 IB918F User’s Manual...
Need help?
Do you have a question about the IB918F and is the answer not in the manual?
Questions and answers