Related Manuals for IBASE Technology IB919 Series
Summary of Contents for IBASE Technology IB919 Series
- Page 1 IB919 Series ® Intel Gen. Core™ ® U-series / Celeron 3.5” Disk-Size SBC User’s Manual Version 1.0A (March 2020)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
- Page 3 0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) IB919 Series User’s Manual...
- Page 4 Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point. IB919 Series User’s Manual...
- Page 5 Software in use (such as OS and application software, including the version numbers) If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. IB919 Series User’s Manual...
-
Page 6: Table Of Contents
COM2, COM3, COM4 RS-232 Ports (J20, J21, J22) ... 24 2.5.10 DC Power Input Connector (J18) ......... 24 2.5.11 Digital I/O Connector (J17) ..........25 2.5.12 LCD Backlight Connector (J15) ........... 25 2.5.13 LVDS Connector (J14, J13)..........26 2.5.14 CPU Fan Connector (CPU_FAN1) ........26 IB919 Series User’s Manual... - Page 7 AMI Graphic Output Protocol Policy........55 4.4.12 USB Configuration ..............56 4.4.13 CSM Configuration ...............57 4.4.14 NVMe Configuration .............58 4.4.15 Network Stack Configuration ..........59 Chipset Settings ................60 Security Settings ................65 Boot Settings ..................66 Save & Exit Settings ................67 IB919 Series User’s Manual...
- Page 8 Appendix ..................68 I/O Port Address Map ................ 69 Interrupt Request Lines (IRQ) ............72 Watchdog Timer Configuration ............74 Onboard Connector Reference Types ..........78 viii IB919 Series User’s Manual...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Optional Accessories • Specifications • Block Diagram • Board Overview • Board Dimensions... -
Page 10: Introduction
Introduction • IB919 series is a 3.5” disk-size single board computer based on the ® ® platform of Intel Gen. Core™ U-series or Celeron processor. It features both HDMI and Display Port at I/O coastline, and onboard headers for dual channel LVDS interface for video display. Advanced features include four USB 3.0, two SATA III, configurable watchdog... -
Page 11: Packing List
• Cable Kit (IB76A-1) Including: DC-In power cable (PW87) COM ports cable (PK1H) SATA & HDD power cable (SATA-53A) USB 2.0 cable (USB29) • Audio cable (Audio-18) • Heat spreader (HSIB919-A) IB919 Series User’s Manual... -
Page 12: Specifications
U-series processor built-in HD audio controller Audio Codec & Controller Realtek ALC269Q codec Power 9 ~ 24V DC-In Requirement 12.X iAMT USB Type C USB 3.1 (Gen.2) RAID Watchdog Yes (256 segments, 0, 1, 2…255 sec / min) Timer IB919 Series User’s Manual... - Page 13 Operation: 0 ~ 60 °C (32 ~ 140 °F) Temperature • Storage: -20 ~ 80 °C (-4 ~ 176 °F) Relative 0 ~ 90 %, non-condensing at 60 °C Humidity All specifications are subject to change without prior notice. IB919 Series User’s Manual...
-
Page 14: Block Diagram
Block Diagram IB919 Series User’s Manual... -
Page 15: Overview
General Information Overview Top View Bottom View Photos of IB919 ＊The photos above are for reference only. Some minor components may differ. IB919 Series User’s Manual... - Page 16 I/O View Name Name COM1 RS-232/422/485 Port Display Port USB 3.0 Ports USB Type-C LAN Port IB919 Series User’s Manual...
-
Page 17: Dimensions
General Information Dimensions IB919 Series User’s Manual... - Page 18 This page is intentionally left blank. IB919 Series User’s Manual...
-
Page 19: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration This section provides information on jumper settings and connectors on the IB919 in order to set up a workable system. On top of that, you will also need to install crucial pieces such as the CPU and the memory before using the product. The topics covered are: •... -
Page 20: Essential Installations Before You Begin
Follow the instructions below to install the memory. 2.1.1 Installing the Memory The IB919 series supports two DDR4 memory sockets for a maximum total memory of 32 GB. To install the modules, locate the memory slot on the board and perform the following steps: Align the key of the memory module with that on the memory slot and insert the module slantwise. -
Page 21: Setting The Jumpers
When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. IB919 Series User’s Manual... -
Page 22: Jumper & Connector Locations
Jumper & Connector Locations Board diagram of IB919 IB919 Series User’s Manual... -
Page 23: Jumpers Quick Reference
EDP Panel Power Selections JP3(For power) / LVDS Panel Power / Brightness Selections JP5 (For brightness) EDP / LVDS Selections Factory Use Only 2.4.1 CMOS Data Clearance (JBAT1) Function Pin closed Illustration Normal (default) Clear CMOS IB919 Series User’s Manual... -
Page 24: Edp Panel Power Selections (Jp2)
EDP Panel Power Selections (JP2) JP2: Jumper Function Pin closed Illustration 3.3V (default) 2.4.3 LVDS Panel Power / Brightness Selections (JP3 / JP5) JP5: JP3: Jumper Function Pin closed Illustration 3.3V (default) 3.3V (default) Open Close IB919 Series User’s Manual... -
Page 25: Edp / Lvds Selections (Jp4)
Hardware Configuration 2.4.4 EDP / LVDS Selections (JP4) JP4: Jumper Function Pin closed Illustration (default) LVDS IB919 Series User’s Manual... -
Page 26: Connectors Quick Reference
CPU_FAN1 SATA III Port CN1, CN2 Display Port GbE LAN Ports USB 3.0 Port CN6, CN7 USB Type-C DDR4 SO-DIMM Slot J4, J7 M.2 E-Key / M.2 M-KEY J8, J12 Factory Use Only J2, J19, J11 IB919 Series User’s Manual... -
Page 27: Com1 Rs-232/422/485 Port (Cn9)
DCD, Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator Ground Assignment RS-232 RS-422 RS-485 DATA- DATA+ Ground Ground Ground IB919 Series User’s Manual... -
Page 28: Amplify Connector (J1)
2.5.2 Amplify Connector (J1) Assignment Assignment SPK_L+ SPK_R- SPK_L- SPK_R+ 2.5.3 Audio Connector (J3) Assignment Assignment Lineout_L Lineout_R JD_FRONT Ground LINEIN_L Linein_R JD_LINEIN Ground MIC_L MIC-R JD_MIC1 Ground IB919 Series User’s Manual... -
Page 29: Sata Hdd Power Connector (J5)
Hardware Configuration 2.5.4 SATA HDD Power Connector (J5) Assignment Assignment Ground Ground +12V 2.5.5 SMBUS Connector (J10) Assignment Assignment +3.3V SMB_DATA SMB_CLK- Ground IB919 Series User’s Manual... -
Page 30: Front Panel Connector (J9)
Orientation is not required when making a connection to this header. • Power LED: Pins 7 and 8 This connector connects to the system power LED on control panel. This LED will light when the system turns on. IB919 Series User’s Manual... -
Page 31: Usb 2.0 Connector (J6)
Hardware Configuration 2.5.7 USB 2.0 Connector (J6) Assignment Assignment Ground Ground 2.5.8 Battery Connector (J16) Assignment Battery+ Ground IB919 Series User’s Manual... -
Page 32: Com2, Com3, Com4 Rs-232 Ports (J20, J21, J22)
TXD, Transmit data DTR, Data terminal ready Ground DSR, Data set ready RTS, Request to send CTS, Clear to send RI, Ring indicator Not Used 2.5.10 DC Power Input Connector (J18) Assignment +9V ~ +24V Ground IB919 Series User’s Manual... -
Page 33: Digital I/O Connector (J17)
Hardware Configuration 2.5.11 Digital I/O Connector (J17) Assignment Assignment Ground OUT3 OUT1 OUT2 OUT0 2.5.12 LCD Backlight Connector (J15) Assignment Assignment +12V Brightness Control Backlight Enable Ground IB919 Series User’s Manual... -
Page 34: Lvds Connector (J14, J13)
Assignment Assignment TX0P TX0N Ground Ground TX1P TX1N Ground Ground TX2P TX2N Ground Ground CLKP CLKN Ground Ground TX3P TX3N Power Power 2.5.14 CPU Fan Connector (CPU_FAN1) Assignment Assignment Ground CPU Fan In CPU Fan Out IB919 Series User’s Manual... -
Page 35: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • ® Intel Chipset Software Installation Utility • VGA Driver • HD Audio Driver • LAN Driver • ® Intel Management Engine Drivers Installation... -
Page 36: Introduction
INF files for Plug & Play function for Intel chipset components. Follow the instructions below to complete the installation. Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Whiskeylake-U Chipset Drivers on the right pane. IB919 Series User’s Manual... - Page 37 Chipset Device Software appears, click Next to continue. Accept the software license agreement and proceed with the installation process. On the Readme File Information screen, click Install. After the installation, click Finish to complete the setup process. IB919 Series User’s Manual...
-
Page 38: Vga Driver Installation
VGA Driver Installation Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Whiskeylake-U Chipset Drivers on the right pane. Click Intel(R) HD Graphics Driver. IB919 Series User’s Manual... - Page 39 Click Yes to accept the license agreement and click Next until the installation starts. On the Readme File Information screen, click Next until the installation starts. On the following screens, click Next when prompted. After the installation, restart the computer for changes to take effect. IB919 Series User’s Manual...
-
Page 40: Hd Audio Driver Installation
HD Audio Driver Installation Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Whiskeylake-U Chipset Drivers on the right pane. Click Realtek High Definition Audio Driver. IB919 Series User’s Manual... - Page 41 Driver Installation On the Welcome screen of the InstallShield Wizard, click Next. Click Next until the installation starts. After the installation, restart the computer for changes to take effect. IB919 Series User’s Manual...
-
Page 42: Lan Driver Installation
LAN Driver Installation Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Whiskeylake-U Chipset Drivers on the right pane. Click Intel(R) PRO LAN Network Drivers.. IB919 Series User’s Manual... - Page 43 On the Setup Options screen, click the checkbox to select the desired driver(s) for installation. Then click Next to continue. The wizard is ready for installation. Click Install. When the Install wizard is completed, click Finish. IB919 Series User’s Manual...
-
Page 44: Intel ® Management Engine Drivers Installation
Intel Management Engine Drivers Installation Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Whiskeylake-U Chipset Drivers on the right pane. Click Intel(R) ME 12.x Drivers. IB919 Series User’s Manual... - Page 45 Driver Installation When the Welcome screen appears, click Next. Accept the license agreement and click Next until the installation starts. After Intel Management Engine Components have been successfully installed, click Finish. IB919 Series User’s Manual...
-
Page 46: Intel ® Serial Io Drivers Installation
Intel Serial IO Drivers Installation Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Whiskeylake-U Chipset Drivers on the right pane. Click Intel(R) Serial IO Drivers. IB919 Series User’s Manual... - Page 47 When the Welcome screen appears, click Next. Accept the license agreement and click Next until the installation starts. When prompted to install the driver, click Next. After completing the installation, restart the computer for changes to take effect. IB919 Series User’s Manual...
- Page 48 This page is intentionally left blank. IB919 Series User’s Manual...
-
Page 49: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 50: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. IB919 Series User’s Manual... -
Page 51: 4.3 Main Settings
Sets the date. Use the <Tab> key to switch System Date between the data elements. Set the time. Use the <Tab> key to switch System Time between the data elements. NOTE: Below is the corresponding screen for the IB919EF BIOS IB919 Series User’s Manual... -
Page 52: 4.4 Advanced Settings
4.4 Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. IB919 Series User’s Manual... -
Page 53: Connectivity Configuration
Seiral IO UART0 needs to be enabled to select BT Discrete Bluetooth Module. Module Default: Disabled Advanced Configure ACPI objects for wireless devices Settings Default: Disabled WWAN Configure WWAN related options. Configuration WWAN Device: enable or disable M.2 WWAN device WWAN Reset Default: Enabled Workaround IB919 Series User’s Manual... -
Page 54: Cpu Configuration
Execution provided by Intel® Trusted Execution Technology. Technology Changes require a full power cycle to take effect. NOTE: The selections for Hyper-Threading Intel Trusted Execution Technology are not available on the IB919EF BIOS as shown below. IB919 Series User’s Manual... -
Page 55: Power & Performance
P-states. Enable/Disable processor Turbo Mode (requires Turbo Mode Intel Speed Steop or Intel Speed Dhift to be available and enabled.) NOTE: The selections for Turbo Mode is not available on the IB919EF BIOS as shown below. IB919 Series User’s Manual... -
Page 56: Pch-Fw Configuration
4.4.4 PCH-FW Configuration Configure Management Engine Technology Parameters IB919 Series User’s Manual... -
Page 57: Trusted Computing
TPM 1.2 will restrict support to TPM 1.2 devices. TPM 2.0 will restrict support to TPM 2.0 devices. Device Select Auto will support both with the default set to TPM 2.0 devices if not found, TPM 1.2 devices will be enumerated. IB919 Series User’s Manual... -
Page 58: Acpi Settings
Enable Hibernation (OS/S4 Sleep State). This option may be not effective with some OS. Selects an ACPI sleep state (Suspend Disabled ACPI Sleep State or S3) where the system will enter when the Suspend button is pressed. IB919 Series User’s Manual... -
Page 59: Lvds Configuration
960, 1280 x 1024, 1366 x 768, 1440 x 900, 1600 x 900, 1600 x 1200, 1680 x 1050, 1920 x 1080, 1920 x 1200 LVDS Brightness Options: 0(Min), 1, 2, 3, 4, 5, 6, 7(Max) Control IB919 Series User’s Manual... -
Page 60: F81964 Super Io Configuration
4.4.8 F81964 Super IO Configuration BIOS Setting Description Sets parameters of serial ports. Serial Ports Enables / Disables the serial port and select an Configuration optimal setting for the Super IO device. IB919 Series User’s Manual... -
Page 61: F81964 Super Io Configuration For Ib919Ef
Sets parameters of serial ports. Serial Ports Enables / Disables the serial port and select an Configuration optimal setting for the Super IO device. Standby Power on Enable: Provide the Standby Power for devices S5(Eup) Disable: Shutdown the standby power IB919 Series User’s Manual... -
Page 62: Hardware Monitor
PC health status. Sets a threshold of temperature to shut down if CPU goes overheated. CPU Shutdown Temperature Options: Disabled / 70 °C / 75 °C / 80 °C / 85 °C / 90 °C / 95 °C IB919 Series User’s Manual... -
Page 63: Ami Graphic Output Protocol Policy
BIOS Setup 4.4.11 AMI Graphic Output Protocol Policy Configure Management Engine Technology Parameters IB919 Series User’s Manual... -
Page 64: Usb Configuration
Max.time the device will take before it properly Device power-up reports itself to the Host Controller. ‘Auto’ uses delay default value: for a Root port it is 100ms, for a Hub port the delay is taken from Hub descriptor. IB919 Series User’s Manual... -
Page 65: Csm Configuration
BIOS Setup 4.4.13 CSM Configuration BIOS Setting Description Controls the execution of UEFI and Legacy PXE Network OpROM. IB919 Series User’s Manual... -
Page 66: Nvme Configuration
4.4.14 NVMe Configuration IB919 Series User’s Manual... -
Page 67: Network Stack Configuration
PXE boot wait time the PXE boot. Use either +/- or numeric keys to set the value Number of times the presence of media will be Media detect count checked. Use either +/- nurmeric keys to set the value. IB919 Series User’s Manual... -
Page 68: 4.5 Chipset Settings
4.5 Chipset Settings 4.5.1 System Agent (SA) Configuration 4.5.1.1. Graphics Configuration: IB919 Series User’s Manual... - Page 69 BIOS Setup IB919 Series User’s Manual...
- Page 70 4.5.1.2. VT-d IB919 Series User’s Manual...
- Page 71 Enables / Disables the Serial ATA. SATA Mode Selection Selects IDE or AHCI Mode. Serial ATA Port 0~2 Enables / Disables Serial Port 0 ~ 2. SATA Ports Hot Plug Enables / Disables SATA Ports HotPlug. IB919 Series User’s Manual...
- Page 72 Enables / Disables onboard NIC. Enables / Disables integrated LAN to wake the Wake on LAN Enable system. Specify what state to go when power is re-applied State After G3 afater a power failure (G3 state). IB919 Series User’s Manual...
-
Page 73: 4.6 Security Settings
User Password Sets a user password. Secure Boot feature is Active if Secure Boot is enabled. Platform Key(PK) is enrolled and the Secure Boot system is in user mode. The mode change requires platform reset. IB919 Series User’s Manual... -
Page 74: 4.7 Boot Settings
Selects the keyboard NumLock state. State Quiet Boot Enables / Disables Quiet Boot option. Boot Mode Select Selects boot mode LEGACY/UEFI FIXED BOOT ORDER Configures the boot order priorities. Up to 9 boot Priorities options can be configured. IB919 Series User’s Manual... -
Page 75: 4.8 Save & Exit Settings
Restores / Loads defaults values for all the setup Restore Defaults options. Save as User Defaults Saves the changes done so far as User Defaults. Restores the user defaults to all the setup Restore User Defaults options. IB919 Series User’s Manual... -
Page 76: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. IB919 Series User’s Manual... -
Page 77: I/O Port Address Map
Motherboard resources 0x00004090-0x00004097 Standard SATA AHCI Controller 0x00004080-0x00004083 Standard SATA AHCI Controller 0x00004060-0x0000407F Standard SATA AHCI Controller 0x00000020-0x00000021 Programmable interrupt controller 0x00000024-0x00000025 Programmable interrupt controller 0x00000028-0x00000029 Programmable interrupt controller 0x0000002C-0x0000002D Programmable interrupt controller 0x00000030-0x00000031 Programmable interrupt controller IB919 Series User’s Manual... - Page 78 Ethernet Controller 0x00003000-0x0000301F PCI Express Root Port #8 - 9DBF for mobile 8th Gen Intel(R) Core(TM) processor family 0x000003F8-0x000003FF Communications Port (COM1) 0x000002F8-0x000002FF Communications Port (COM2) 0x000003E8-0x000003EF Communications Port (COM3) 0x000002E8-0x000002EF Communications Port (COM4) 0x00000040-0x00000043 System timer IB919 Series User’s Manual...
- Page 79 Programmable interrupt controller 0x000000AC-0x000000AD Programmable interrupt controller 0x000000B0-0x000000B1 Programmable interrupt controller 0x000000B4-0x000000B5 Programmable interrupt controller 0x000000B8-0x000000B9 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller 0x000004D0-0x000004D1 Programmable interrupt controller 0x00000060-0x00000060 Standard PS/2 Keyboard 0x00000064-0x00000064 Standard PS/2 Keyboard 0x00001854-0x00001857 Motherboard resources IB919 Series User’s Manual...
-
Page 80: Interrupt Request Lines (Irq)
IRQ 4294967293 Standard SATA AHCI Controller IRQ 1 Standard PS/2 Keyboard IRQ 12 Microsoft PS/2 Mouse IRQ 4294967290 Intel(R) USB 3.1 eXtensible Host Controller - 1.10 (Microsoft) IRQ 14 Intel(R) Serial IO GPIO Host Controller - INT34BB IB919 Series User’s Manual... - Page 81 IRQ 4294967293 Standard SATA AHCI Controller IRQ 1 Standard PS/2 Keyboard IRQ 12 Microsoft PS/2 Mouse IRQ 4294967290 Intel(R) USB 3.1 eXtensible Host Controller - 1.10 (Microsoft) IRQ 14 Intel(R) Serial IO GPIO Host Controller - INT34BB IB919 Series User’s Manual...
-
Page 82: Watchdog Timer Configuration
**endptr; char SIO; printf("Fintek 81866 watch dog program\n"); SIO = Init_F81866(); if (SIO == 0) printf("Can not detect Fintek 81866, program abort.\n"); return(1); }//if (SIO == 0) if (argc != 2) printf(" Parameter incorrect!!\n"); return (1); IB919 Series User’s Manual... - Page 83 DisableWDT(void) unsigned char bBuf; Set_F81866_LD(0x07); //switch to logic device 7 bBuf = Get_F81866_Reg(0xFA); bBuf &= ~0x01; Set_F81866_Reg(0xFA, bBuf); //disable WDTO output bBuf = Get_F81866_Reg(0xF5); bBuf &= ~0x20; bBuf |= 0x40; Set_F81866_Reg(0xF5, bBuf); //disable WDT //--------------------------------------------------------------------------- //--------------------------------------------------------------------------- IB919 Series User’s Manual...
- Page 84 Init_Finish; F81866_BASE = 0x00; result = F81866_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_F81866 (void) outportb(F81866_INDEX_PORT, F81866_UNLOCK); outportb(F81866_INDEX_PORT, F81866_UNLOCK); //--------------------------------------------------------------------------- void Lock_F81866 (void) outportb(F81866_INDEX_PORT, F81866_LOCK); //--------------------------------------------------------------------------- void Set_F81866_LD( unsigned char LD) Unlock_F81866(); outportb(F81866_INDEX_PORT, F81866_REG_LD); outportb(F81866_DATA_PORT, LD); Lock_F81866(); IB919 Series User’s Manual...
- Page 85 F81866_DATA_PORT (F81866_BASE+1) //--------------------------------------------------------------------------- #define F81866_REG_LD 0x07 //--------------------------------------------------------------------------- #define F81866_UNLOCK 0x87 #define F81866_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_F81866(void); void Set_F81866_LD( unsigned char); void Set_F81866_Reg( unsigned char, unsigned char); unsigned char Get_F81866_Reg( unsigned char); //--------------------------------------------------------------------------- #endif // F81866_H IB919 Series User’s Manual...
-
Page 86: Onboard Connector Reference Types
Hao Guo Xing Ye Connector WAFER396-2S-WV VHR-2N Dupon Digital I/O Dupon 2.00 mm-pitch pin Connector 2.00 mm-pitch (Female) header (Male) LCD Backlight E-CALL Connector 0110-161-040 PHR-4. J14 (1st channel), LVDS Hirose Hirose Connectors DF20G-20DP-1V DF20A-20DS-1C J13 (2nd channel) IB919 Series User’s Manual...
Need help?
Do you have a question about the IB919 Series and is the answer not in the manual?
Questions and answers