Related Manuals for IBASE Technology IB818F-I50
Summary of Contents for IBASE Technology IB818F-I50
- Page 1 IB818F Series ® ® ® Intel Pentium / Celeron Atom™ x7 SoC 3.5” Disk-Size SBC User’s Manual Version 2.0 (Oct. 2019)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
- Page 3 Compliance The product described in this manual complies with all applicable European Union (CE) directives if it has a CE marking. For systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques. This product has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules.
- Page 4 Important Safety Information Carefully read the safety information before using the board. Environmental conditions: • Use this product in environments with ambient temperatures of 0˚C ~ 60˚C, or -40˚C ~d 85 ˚C based on the specifications of the board you have purchased.
- Page 5 Warranty Policy • IBASE standard products: 24-month (2-year) warranty from the date of shipment. If the date of shipment cannot be ascertained, the product serial numbers can be used to determine the approximate shipping date. • -party parts: 12-month (1-year) warranty from delivery for the 3 -party parts that are not manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices, power adapter, panel and touchscreen.
-
Page 6: Table Of Contents
Table of Contents Chapter 1 General Information ..........1 Introduction ..................2 Features ....................2 Packing List ..................3 Optional Accessories ................3 Specifications ..................4 Block Diagram ..................6 Overview ..................... 7 Dimensions ..................9 Chapter 2 Hardware Configuration ........11 Basic Installations ................ - Page 7 Chapter 3 Drivers Installation ..........21 Introduction ..................22 ® Intel Chipset Software Installation Utility ...........22 VGA Driver Installation ...............24 HD Audio Driver Installation ...............26 ® Intel Trusted Execution Engine Drivers ..........28 ® Intel Serial IO Drivers ...............30 LAN Driver Installation ...............32 Chapter 4 BIOS Setup............
- Page 8 This page is intentionally left blank. IB818F User’s Manual viii...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Block Diagram • Specifications • Board Overview • Board Dimensions... -
Page 10: Introduction
2 x Gigabit LAN, 4 x USB 3.0, 2 x USB 2.0, 4 x COM, 2 x SATA III, 2 x Mini PCIe slot (full-size & half-size) • TPM, Watchdog timer, Digital I/O, mSATA, EuP/ErP • Wide-range operating temperature support for IB818F-I50, IB818F-I40, IB818F-I30 IB818F User’s Manual... -
Page 11: Packing List
◼ SATA cable (SATA-53) ◼ Power cable (PW87) ◼ COM ports cable (PK1H) ◼ USB cable (USB29) x 1 • Heatsink for IB818F-I50, IB818F-I40, IB818F-I30 (HSIB818-I) • Heatsink for IB818F-420 / IB818F-335 (HSIB818) • Audio cable (Audio-18) IB818F User’s Manual... -
Page 12: Specifications
Specifications IB818F-I50 IB818F-420 Product IB818F-I40 Name IB818F-335 IB818F-I30 3.5” disk-size SBC Form Factor System • Windows 10 Enterprise (64-bit) Operating • Windows 10 IoT Core (64-bit) System • Linux Ubuntu • Intel® Atom™ QC x7 / E3950 • Intel ®... - Page 13 General Information IB818F-I50 IB818F-420 Product IB818F-I40 Name IB818F-335 IB818F-I30 • EuP/ErP Smart • Power failure detection (via jumper) Control • LVDS brightness control 102.22 x 147.01 mm (4.02” x 5.8”) Dimensions RoHS Certification CE, FCC Class B I/O Ports • 1 x HDMI (1.4b): 3840 x 2160 at 30Hz Display •...
-
Page 14: Block Diagram
Block Diagram IB818F User’s Manual... -
Page 15: Overview
General Information Overview Top View Bottom View Photo of IB818F ＊The photos above are for reference only. IB818F User’s Manual... - Page 16 I/O View ＊The I/O interface includes the following: • D-SUB RS-232/422/485 port (CN10) • HDMI port (CN9) • LAN ports (CN5, CN6) • USB 3.0 ports (CN7, CN8) IB818F User’s Manual...
-
Page 17: Dimensions
General Information Dimensions IB818F User’s Manual... - Page 18 This page is intentionally left blank. IB818F User’s Manual...
-
Page 19: Chapter 2 Hardware Configuration
Chapter 2 Hardware Configuration This section provides information on jumper settings and connectors on the IB818F to help you set up a workable system. The topics covered are: • CPU and the memory installation • Jumper settings and connectors... -
Page 20: Basic Installations
2.1 Basic Installations Follow the instructions below to install the memory module. 2.1.1 Installing the Memory The IB818F board supports two DDR3L memory sockets for a maximum total memory of 8 GB. To install the memory modules, locate the memory slot on the board and perform the following steps: Align the notch of the memory module with that on the memory slot, and insert the module slantwise. -
Page 21: Setting The Jumpers
Hardware Configuration 2.2 Setting the Jumpers Configure your IB818F by using jumpers to enable the features that you need based on your applications. Contact your supplier if you have doubts about the best configuration or settings. 2.2.1 How to Set Jumpers Jumpers are short-length conductors consisting of several metal pins with a base mounted on the circuit board. -
Page 22: Jumper & Connector Locations
2.3 Jumper & Connector Locations Board diagram of IB818F IB818F User’s Manual... -
Page 23: Jumpers Quick Reference
Hardware Configuration 2.4 Jumpers Quick Reference Function Jumper Name Page LCD Panel Brightness Selection JP1, JP4 LVDS Panel Power Selection JP2, JP3 LCD Panel Backlight VCC JP5, JP6 ATX / AT Power Selection Clearing CMOS Data Clearing ME Register Factory Use Only JP10 2.4.1 LVDS Panel Brightness Selection (JP1, JP4) Function... -
Page 24: Atx / At Power Selection (Jp7)
2.4.4 ATX / AT Power Selection (JP7) Function Pin closed Illustration (default) 2.4.5 Clearing CMOS Data (JP8) Function Pin closed Illustration Normal (default) Clear CMOS 2.4.6 Clearing ME Register (JP9) Function Pin closed Illustration Normal (default) Clear ME IB818F User’s Manual... -
Page 25: Connectors Quick Reference
Hardware Configuration 2.5 Connectors Quick Reference Function Connector Name Page SATA III CN1, CN2 LAN Ports CN5, CN6 USB 3.0 CN7, CN8 HDMI LCD Backlight J3,J6 CH1: J4, CH2: J1 LVDS CH1: J5, CH2: J2 Audio DDR3L SO-DIMM USB 2.0 Amplifier SATA HDD Power COM2 / COM3 / COM4 RS-232... -
Page 26: Lcd Backlight Connector (J3, J6)
2.5.1 LCD Backlight Connector (J3, J6) Signal Name Signal Name +12V / +5V Brightness Control Backlight Enable Ground 2.5.2 LVDS Connector (CH1: J4, CH2: J1) (CH1: J5, CH2: J2) Signal Name Signal Name TX0P TX0N Ground Ground TX1P TX1N Ground Ground TX2P TX2N... -
Page 27: Usb 2.0 Connector (J10)
Hardware Configuration 2.5.4 USB 2.0 Connector (J10) Signal Name Signal Name Ground Ground 2.5.5 Amplifier Connector (J9) Signal Name Signal Name OUTL+ OUTR- OUTL- OUTR+ 2.5.6 SATA HDD Power Connector (J12) Signal Name Signal Name Ground Ground +12V 2.5.7 COM2 / COM3 / COM4 RS-232 Port (J18, J19, J14) Signal Name Signal Name DCD,... -
Page 28: Front Panel Connector (J16)
2.5.8 Front Panel Connector (J16) Signal Name Signal Name Ground PWR_BTN 3.3V HDD Active Ground Reset Ground 2.5.9 Digital I/O Connector (J22) Signal Name Signal Name Ground OUT3 OUT1 OUT2 OUT0 2.5.10 DC Power Input (J21) Signal Name Signal Name +12V ~ +24V Ground 2.5.11... -
Page 29: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • ® Intel Chipset Software Installation Utility • VGA Driver • HD Audio Driver • ® Intel Trusted Execution Engine Installation • ® Intel Serial I/O Drivers • LAN Driver... -
Page 30: Introduction
Introduction This section describes the installation procedures for software and drivers. The software and drivers are included with the motherboard. If you find anything missing, please contact the distributor where you made the purchase. The contents of this section include the following: Note: After installing your Windows operating system, you must install the ®... - Page 31 Driver Installation Click Intel(R) Chipset Software Installation Utility. ® When the Welcome screen to the Intel Chipset Device Software appears, click Next to continue. Click Yes to accept the software license agreement and proceed with the installation process. On the Readme File Information screen, click Install for installation. After the driver has been completely installed, restart the computer for changes to take effect.
-
Page 32: Vga Driver Installation
VGA Driver Installation Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) Apollolake Graphics Driver. IB818F User’s Manual... - Page 33 Driver Installation When the Welcome screen appears, click Next to continue. Click Yes to accept the license agreement and click Next until the installation starts. After the driver has been completely installed, restart the computer for changes to take effect. IB818F User’s Manual...
-
Page 34: Hd Audio Driver Installation
HD Audio Driver Installation Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Realtek High Definition Audio Driver. IB818F User’s Manual... - Page 35 Driver Installation On the Welcome screen of the InstallShield Wizard, click Next for installation. Click Next until the installation starts. After the driver has been completely installed, restart the computer for changes to take effect. IB818F User’s Manual...
-
Page 36: Intel ® Trusted Execution Engine Drivers
® Intel Trusted Execution Engine Drivers Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) TXE Drivers. IB818F User’s Manual... - Page 37 Driver Installation When the Welcome screen appears, click Next. Accept the license agreement and click Next. Click Next for installation. After the driver has been successfully installed, restart the computer for changes to take effect. IB818F User’s Manual...
-
Page 38: Intel ® Serial Io Drivers
® Intel Serial IO Drivers Click Intel on the left pane and then Intel(R) Apollolake Chipset Drivers on the right pane. Click Intel(R) Serial IO Drivers. IB818F User’s Manual... - Page 39 Driver Installation When the Welcome screen to the InstallShield Wizard appears, click Next. Accept the license agreement and click Next. After reading the Readme File Information, click Next for installation. After the driver has been sccessfully installed, restart the computer for changes to take effect.
-
Page 40: Lan Driver Installation
LAN Driver Installation Click LAN Card on the left pane and then Intel LAN Controller Drivers on the right pane. Click Intel(R) I21x Gigabit Network Drivers.. IB818F User’s Manual... - Page 41 Driver Installation When the Welcome screen appears, click Next. Accept the license agreement and click Next. On the Setup Options screen, click the checkbox to select the desired driver(s) for installation. Then click Next to continue. The wizard is ready for installation. Click Install. After the installation is complete, restart the computer for changes to take effect.
- Page 42 This page is intentionally left blank. IB818F User’s Manual...
-
Page 43: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •... -
Page 44: Introduction
4.1 Introduction The BIOS (Basic Input/Output System) installed in the ROM of your ® computer system supports Intel processors. The BIOS provides critical low-level support for standard devices such as disk drives, serial ports and parallel ports. It also provides password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system. -
Page 45: Main Settings
BIOS Setup 4.3 Main Settings BIOS Setting Description System Date Sets the date. Use the <Tab> key to switch between the data elements. System Time Set the time. Use the <Tab> key to switch between the data elements. IB818F User’s Manual... -
Page 46: Advanced Settings
4.4 Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. IB818F User’s Manual... -
Page 47: Acpi Computing
BIOS Setup 4.4.1 ACPI Computing BIOS Setting Description Enable Hibernation Enables / Disables the system ability to hibernate (OS/S4 Sleep State). This option may be not effective with some OS. ACPI Sleep State Selects an ACPI sleep state (Suspend Disabled or S3) where the system will enter when the Suspend button is pressed. -
Page 48: Lfp (Edp) To Lvds Configuration
4.4.2 LFP (eDP) to LVDS Configuration BIOS Setting Description LVDS Support Enables / Disables eDP to LVDS. Panel Color Depth Selects a panel color depth as 18 or 24 (VESA or JEIDA) bit. LVDS Channel Type Sets the LVDS channel type as single or dual channel. -
Page 49: Efp (Dp) To Lvds Configuration
BIOS Setup 4.4.3 EFP (DP) to LVDS Configuration BIOS Setting Description LVDS Support Enables / Disables DP to LVDS. Panel Color Depth Selects a panel color depth as 18 or 24 (VESA or JEIDA) bit. LVDS Channel Type Sets the LVDS channel type as single or dual channel. -
Page 50: Fintek Super Io Configuration
4.4.4 Fintek Super IO Configuration BIOS Setting Description Standby Power on S5 Enable the item to provide the standby power for (ERP) devices. Disable the item to shut down the standby power. Options: All Enable / Enable Ethernet for WOL / All Disable Serial Ports Sets parameters of serial ports. - Page 51 BIOS Setup 4.4.4.1. Serial Port 1 Configuration BIOS Setting Description Serial Port Enables / Disables the serial port. Change Settings Selects an optimal settings for Super IO device. Device Mode Changes the serial port mode to: • RS232 • RS485 TX Low Active •...
-
Page 52: Fintek Super Io Hardware Monitor
4.4.5 Fintek Super IO Hardware Monitor BIOS Setting Description Temperatures / These fields are the parameters of the hardware Voltages monitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status. CPU Shutdown Sets a threshold of temperature to shut down if Temperature... -
Page 53: Cpu Configuration
BIOS Setup 4.4.6 CPU Configuration BIOS Setting Description Socket 0 CPU Displays the socket specific CPU information. Information CPU Power Allows you to enable / disable Turbo Mode. Management Active Processor Enables / Disables the cores in the processor Cores package. - Page 54 4.4.6.1. Socket 0 CPU Information 4.4.6.2. CPU Power Management Configuration BIOS Setting Description Turbo Mode Enables / Disables the turbo mode. IB818F User’s Manual...
-
Page 55: Ami Graphic Output Protocol Policy
BIOS Setup 4.4.7 AMI Graphic Output Protocol Policy BIOS Setting Description Output Select Outputs through HDMI interface. IB818F User’s Manual... -
Page 56: Network Stack Configuration
4.4.8 Network Stack Configuration BIOS Setting Description Network Stack Enables / Disables UEFI Network Stack. IPv4 PXE Support Enables / Disables IPv4 PXE Boot Support. If disabled, Ipv4 PXE boot option will not be created. IPv4 HTTP Support Enables / Disables IPv4 HTTP Boot Support. If disabled, Ipv4 HTTP boot option will not be created. -
Page 57: Csm Configuration
BIOS Setup 4.4.9 CSM Configuration BIOS Setting Description CSM Support Enables / Disables CSM support. • GateA20 Active Upon Request disables GA20 when using BIOS services. • Always cannot disable GA20, but is useful when any RT code is executed above 1 MB. INT19 Trap Response Sets how BIOS reacts on INT19 trap by Option ROM. -
Page 58: Usb Configuration
4.4.10 USB Configuration BIOS Setting Description • Legacy USB Support Enabled enables Legacy USB support. • Auto disables legacy support if there is no USB device connected. • Disabled keeps USB devices available only for EFI applications. XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. -
Page 59: Chipset Settings
BIOS Setup 4.5 Chipset Settings 4.5.1 North Bridge BIOS Setting Description Max TOLUD Sets a maximum value of TOLUD. IB818F User’s Manual... -
Page 60: South Cluster Configuration
4.5.2 South Cluster Configuration 4.5.2.1. HD Audio Configuration BIOS Setting Description HD-Audio Support Enables / Disables HD-Audio support. IB818F User’s Manual... - Page 61 BIOS Setup 4.5.2.2. PCI Express Configuration BIOS Setting Description PCI Express Root Accesses the control of the PCI Express Root Port 1 ~ 6 Port. IB818F User’s Manual...
- Page 62 BIOS Setting Description PCI Express Root Enables/ Disables the PCIe root port. Port Auto allows you to disable unused root port automatically for the most optimum power savings. ASPM Sets the PCIe active state power management. Options: Disable / L0s / L1 / L0SL1 / Auto L1 Substates Sets PCIe L1 substates.
- Page 63 BIOS Setup 4.5.2.3. SATA Drivers BIOS Setting Description Chipset SATA Enables / Disables the Chipset SATA Controller. The Chipset SATA Controller supports the 2 black internal SATA ports (up to 3Gb/s supported per port). SATA Mode Selection Determines how SATA controller(s) operate. IB818F User’s Manual...
- Page 64 4.5.2.4. USB Configuration BIOS Setting Description XHCI Pre-Boot Driver Enables / Disables the support for XHCI Pre-Boot Driver. XHCI Mode Enables / Disables XHCI mode. If disabled, XHCI controller would be disabled, and none of the USB devices are detectable or usable when systen is booted up in OS.
-
Page 65: Security Settings
BIOS Setup 4.6 Security Settings BIOS Setting Description Setup Administrator Sets an administrator password for the setup Password utility. User Password Sets a user password. IB818F User’s Manual... -
Page 66: Boot Settings
4.7 Boot Settings BIOS Setting Description Setup Prompt Number of seconds to wait for setup activation Timeout key. 65535 (0xFFFF) means indefinite waiting. Bootup NumLock Selects the keyboard NumLock state. State Quiet Boot Enables / Disables Quiet Boot option. New Boot Option Controls the placement of newly detected UEFI Policy boot options. -
Page 67: Save & Exit Settings
BIOS Setup 4.8 Save & Exit Settings BIOS Setting Description Save Changes and Exits system setup after saving the changes. Exit Discard Changes and Exits system setup without saving any changes. Exit Save Changes and Resets the system after saving the changes. Reset Discard Changes and Resets system setup without saving any... - Page 68 This page is intentionally left blank. IB818F User’s Manual...
-
Page 69: Appendix
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. -
Page 70: I/O Port Address Map
I/O Port Address Map Each peripheral device in the system is assigned a set of I/O port addresses which also becomes the identity of the device. The following table lists the I/O port addresses used. Address Device Description 0x00000A00-0x00000A0F Motherboard resources 0x00000A10-0x00000A1F Motherboard resources 0x00000A20-0x00000A2F... - Page 71 Appendix 0x000003E8-0x000003EF Communications Port (COM3) 0x000002E8-0x000002EF Communications Port (COM4) Intel(R) Celeron(R)/Pentium(R) 0x0000E000-0x0000EFFF Processor PCI Express Root Port - 5AD8 0x00000000-0x0000006F PCI Express Root Complex 0x00000078-0x00000CF7 PCI Express Root Complex 0x00000D00-0x0000FFFF PCI Express Root Complex 0x00000020-0x00000021 Programmable interrupt controller 0x00000024-0x00000025 Programmable interrupt controller 0x00000028-0x00000029 Programmable interrupt controller 0x0000002C-0x0000002D...
- Page 72 IB818F User’s Manual...
-
Page 73: Interrupt Request Lines (Irq)
Appendix Interrupt Request Lines (IRQ) Peripheral devices use interrupt request lines to notify CPU for the service required. The following table shows the IRQ used by the devices on board. Level Function IRQ 25 High Definition Audio Controller IRQ 4294967280 ~ Intel(R) I210 Gigabit Network Connection IRQ 4294967285 IRQ 8... -
Page 74: Watchdog Timer Configuration
Watchdog Timer Configuration The Watchdog Timer (WDT) is used to generate a variety of output signals after a user programmable count. The WDT is suitable for use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. - Page 75 Appendix bTime = strtol (argv[1], endptr, 10); printf("System will reset after %d seconds\n", bTime); if (bTime) EnableWDT(bTime); } else DisableWDT(); } return 0; //--------------------------------------------------------------------------- void EnableWDT(int interval) unsigned char bBuf; bBuf = Get_F81964_Reg(0x2B); bBuf &= (~0x20); Set_F81964_Reg(0x2B, bBuf); //Enable WDTO Set_F81964_LD(0x07);...
- Page 76 // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. //--------------------------------------------------------------------------- #include "F81964.H" #include <dos.h>...
- Page 77 Appendix //--------------------------------------------------------------------------- void Set_F81964_Reg( unsigned char REG, unsigned char DATA) Unlock_F81964(); outportb(F81964_INDEX_PORT, REG); outportb(F81964_DATA_PORT, DATA); Lock_F81964(); //--------------------------------------------------------------------------- unsigned char Get_F81964_Reg(unsigned char REG) unsigned char Result; Unlock_F81964(); outportb(F81964_INDEX_PORT, REG); Result = inportb(F81964_DATA_PORT); Lock_F81964(); return Result; //--------------------------------------------------------------------------- //--------------------------------------------------------------------------- // THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE.
-
Page 78: Onboard Connector Types
Onboard Connector Types Connector Compatible Mating Function Onboard Type Name Type for Reference LCD Backlight J3,J6 E-CALL JST PHR-4 0110-161-040 LVDS CH1: J4, HIROSE CH2: J1, DF20G-20DP-1V(56) CH1: J5, DF20A-20DS-1C CH2: J2 Audio DF11-12S-PA66H DF11-12DS-2C USB 2.0 DF11-8S-PA66H DF11-8DS-2C Amplifier E-CALL JST PHR-4 0110-161-040...