Page 1 FusionModule500 Smart Mini Data Center V100R021C10 User Manual (02116410, 02116411, 021164112) Issue Date 2023-10-31 HUAWEI DIGITAL POWER TECHNOLOGIES CO., LTD.
Page 2 Notice The purchased products, services and features are stipulated by the contract made between Huawei Digital Power Technologies Co., Ltd. and the customer. All or part of the products, services and features described in this document may not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information, and recommendations in this document are provided "AS IS"...
Page 3: About This Document
User Manual (02116410, 02116411, 021164112) About This Document About This Document Purpose This document describes the FusionModule500 Smart Mini Data Center (smart module for short) in terms of its installation, commissioning, operation, and maintenance. Intended Audience This document is intended for: ●...
Page 4 Change History Issue Date Description 2023-10-31 Updated section "iManager-M." 2022-08-20 Updated section "Power- On Commissioning." 2022-02-25 Updated section "(Optional) Installing a Camera." 2021-07-15 This issue is the first official release. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 5: Table Of Contents
3.2.5.1 Non-intelligent rPDU..............................38 3.2.5.2 Intelligent rPDU................................39 3.2.6 Lithium Battery ESM-48100B1............................39 3.3 Cooling System..................................40 3.3.1 Application Conditions..............................41 3.3.2 Technical Specifications..............................41 3.4 Management System................................42 3.4.1 Overview....................................42 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 6 4.1.1 Tools and Instruments..............................74 4.1.2 Installation Environment Check........................... 77 4.1.3 Site Equipment Preparation............................79 4.1.4 Installation Scenarios............................... 80 4.1.5 Configuration Scenario..............................83 4.1.6 Personnel Requirements..............................86 4.2 Hardware Installation................................86 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 7 5.1.1.1 Checking Before Power-On............................139 5.1.1.2 UPS Startup Method..............................139 5.1.1.3 Starting a UPS................................141 5.1.1.4 UPS Shutdown Method............................. 142 5.1.1.5 Shutting Down a UPS..............................142 5.1.1.6 Cold-Starting the UPS Using Batteries (Single UPS)..................142 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 8 5.3.12.3 Obtaining the NetEco Software License......................214 5.3.12.4 Obtaining the Adapter Software Installation Packages................215 5.3.12.5 Powering On a Server.............................. 216 5.3.12.6 Logging In to the NetEco Client...........................216 5.3.12.7 Loading the NetEco Software License....................... 217 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 9 6.4.2 Replacing Power Supply and Distribution System Components..............271 6.4.2.1 Replacing a Surge Protection Module........................271 6.4.2.2 Replacing a Fuse................................273 6.4.2.3 Replacing an rPDU..............................274 6.4.2.4 Replacing a Transformer............................274 6.4.2.5 Replacing a UPS2000-H............................277 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd. viii...
Page 10 6.4.4.8 Replacing a Smoke Detector........................... 308 6.4.4.9 Replacing an Electrode Water Sensor........................309 6.4.4.10 Replacing a Door Status Sensor........................... 309 7 Technical Specifications.....................310 A Equipment Derating Coefficients..................312 B Acronyms and Abbreviations................... 313 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 11: Safety Information
Equipment damage due to force majeure such as earthquakes, floods, volcanic eruptions, debris flows, lightning strikes, fires, wars, armed conflicts, typhoons, hurricanes, tornadoes, and extreme weather conditions ● Operation beyond the conditions specified in this document Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 12: Personal Safety
D ANGER During operations, use dedicated insulated tools to prevent electric shocks or short circuits. The insulation and voltage resistance must comply with local laws, regulations, standards, and specifications. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 13 – Trained personnel: personnel who are trained in technology and safety, have required experience, are aware of possible hazards on themselves in Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 14: Electrical Safety
WARNING For the equipment that needs to be grounded, install the ground cable first when installing the equipment and remove the ground cable last when removing the equipment. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 15 (The marks must cross the edges of the bolts.) ● After the installation is complete, ensure that protective cases, insulation tubes, and other necessary items for all electrical components are in position to avoid electric shocks. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 16 When selecting, installing, and routing cables, follow local safety regulations and rules. ● The flame spread rating of cables shall meet the UL 1581 VW-1 or IEC 60332-3-22 (ZB) or higher requirements. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 17 When touching the equipment and handling boards, modules with exposed circuit boards, or application-specific integrated circuits (ASICs), observe ESD protection regulations and wear ESD clothing and ESD gloves or a well- grounded ESD wrist strap. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 19 All cable holes must be sealed. Seal the used cable holes with sealing putty. Seal the unused cable holes with the caps delivered with the equipment. The following figure shows the criteria for correct sealing with sealing putty. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 20: Mechanical Safety
Otherwise, tipping or falling cabinets may cause bodily injury and equipment damage. WARNING When pulling equipment out of a cabinet, be aware of unstable or heavy objects in the cabinet to prevent injury. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 22 Personnel involving working at heights are not allowed to throw objects from the height to the ground, or vice versa. Objects shall be transported by slings, hanging baskets, aerial work platforms, or cranes. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 23 If a single ladder is used, the recommended angle for the ladder against the floor is 75 degrees, as shown in the following figure. A square can be used to measure the angle. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 24 Do not drag steel ropes and hoisting tools or bump hoisted objects against hard objects during hoisting. ● Ensure that the angle between two hoisting ropes is no more than 90 degrees, as shown in the following figure. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 25: Equipment Safety
Otherwise, the gas may leak and cause a fire. ● High-temperature pipes after welding must be promptly cooled. 1.5 Equipment Safety Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 26: Ups Safety
Exercise caution when manually shutting down the UPS inverter for transferring to bypass mode, or when adjusting the UPS output voltage level or output frequency. Doing so may affect the power supply to equipment. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 27: Cooling System Safety
Do not expose batteries at high temperatures or around heat sources, such as scorching sunlight, fire sources, transformers, and heaters. Battery overheating may cause leakage, smoke, flammable gas release, thermal runaway, fire, or explosion. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 29 ● Batteries are damaged due to force majeure such as earthquakes, floods, volcanic eruptions, debris flows, lightning strikes, fires, wars, armed conflicts, typhoons, hurricanes, tornadoes, and extreme weather conditions. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 30 The safety precautions specified in this document are highly important and require special attention. For additional safety precautions, see the instructions provided by the battery vendors. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 31 When installing and maintaining batteries, wrap the exposed cable terminals on the batteries with insulation tape. ● Avoid foreign objects (such as conductive objects, screws, and liquids) from entering a battery, as this may cause short circuits. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 32 Do not place waste batteries in environments with high humidity or corrosive substances. ● Do not use faulty batteries. Contact a battery recycling company to scrap them as soon as possible to avoid environmental pollution. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 33: Overview
To meet the requirements for customers' growing services, the Company launches the FusionModule500 that can be rapidly deployed and flexibly expanded. The FusionModule500 is positioned as a small edge data center solution and occupies about 10 m . It is mainly used in the equipment rooms of county-level governments, bank business outlets, and small- and medium-sized enterprises.
Page 34 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 2 Overview Figure 2-1 Position of the FusionModule500 in the financial industry (1) FusionModule5000 (2) FusionModule2000 (3) FusionModule800 (4) FusionModule500 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 35: Features
FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 2 Overview Figure 2-2 Position of the FusionModule500 for governments (1) FusionModule5000 (2) FusionModule2000 (3) FusionModule800 (4) FusionModule500 2.2 Features High Integration The smart module provides a comprehensive solution by integrating the cabinet...
Page 36: Typical Application Scenarios And Configurations
The solution supports the 220 V/230 V/240 V, 1 Ph, 50/60 Hz power systems. ● Latin America: The solution supports the 208 V, 2 Ph, 60 Hz power system. 2.3.2 Typical Configurations Figure 2-3 Converged Cabinet (02116410) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 37 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 2 Overview Figure 2-4 Converged Cabinet (02116411) Figure 2-5 Converged Cabinet (02116412) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 38 (optional), WiFi NetEco (optional) NetEco (optional) module (optional), and NetEco (optional) Fire extinguishing Room-level fire Rack-mounted Rack-mounted system control linkage integrated fire integrated fire extinguishing extinguishing device (optional) device (optional) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 39: System Architecture
Air channel Cold and hot aisle containment Installation mode Installed on a concrete floor or electrostatic discharge (ESD) floor Static load 2400 kg Dynamic load 1000 kg IP rating IP20 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 40: Power Supply And Distribution System
The UPS supplies uninterruptible power to loads by means of lithium batteries when the external power supply fails. Figure 3-1 Power distribution diagram in Asia, Africa, and Europe (02116410 & 02116411) Figure 3-2 Power distribution diagram in Latin America (02116412) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 41: Power Distribution Subrack
Dimensions (H x W x D) 130 mm x 442 mm x 450 mm 3.2.3 Transformer Figure 3-3 Transformer Table 3-3 Transformer technical specifications Item Specifications Rated capacity 10 kVA Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 42: Ups2000-H-6 Kva
(5) Inverter indicator (6) WiFi indicator (7) Load rate indicator (8) Battery SOC indicator (10) Battery ports (11) AC input ports (12) AC output ports (9) Label Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 43 0.5s to enable the WiFi (the WiFi indicator is on). Disabling WiFi When the WiFi is enabled, hold down the button for 0.5s to disable the WiFi (the WiFi indicator is off). Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 44 Steady on Inverter mode indicator Non-inverter mode WiFi indicator Green Steady on WiFi enabled Blinking The mobile phone is connected to the WiFi network of the UPS. WiFi disabled Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 45 50% indicator: steady 75% indicator: When the battery SOC is 50%, the indicator is off. When the battery SOC is greater than 50%, the indicator blinks. 100% indicator: off Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 46 25% indicator: steady 50% indicator: When the load rate is 25%, the indicator is off. When the load rate is greater than 25%, the indicator blinks. Other indicators: off Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 47 Table 3-6 Functions of CAN communications ports Silk Screen Function Used for lithium battery communication MON1 Used for ECC800-Pro communication Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 48: Rpdu
Full-Height rPDU) Rated current 16 A 40 A Input frequency 50 Hz/60 Hz 50 Hz/60 Hz Input port Cord end terminal, no Cord end terminal, no input cable input cable Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 49: Intelligent Rpdu
3.2.6 Lithium Battery ESM-48100B1 Lithium batteries provide backup power. When the mains is normal, the UPS charges batteries. When the mains fails, lithium batteries supply power to the UPS. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 50: Cooling System
100 A/100 A@35°C (The actual charge current current depends on the UPS charge capability.) Maximum charge/discharge 4800 W power Installation mode Rack-mounted 3.3 Cooling System Figure 3-9 Integrated air conditioner Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 51: Application Conditions
208–240 V AC, 50 Hz/60 Hz, 1 Ph Refrigerant R410A Cooling capacity 3.5 kW Air supply mode Front flow or front upflow Dimensions (H x W x D) 355 mm x 442 mm x 930 mm Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 52: Management System
It also provides a graphical user interface (GUI) for ease of operating and maintaining devices inside the smart module. Figure 3-10 System networking diagram (02116410) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 53: System Functions
T/H sensor. The ambient temperature and humidity are also displayed on the home page of the app. ● Displays the real-time status monitoring data and alarms of the aisle temperature and humidity on the floor plan. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 54: Alarm
If the protected area of the fire extinguishing system is outside the smart module, when a smoke alarm is generated, the rear door of the linked cabinet is opened. 3.4.3 Key Hardware Devices 3.4.3.1 ECC800-Pro Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 55: Product Configuration
442 mm x 330 mm x 43.6 mm Color Black Installation requirements Can be installed in a 1 U space in a standard 19-inch cabinet Environmental protection RoHS5, REACH, WEEE Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 56: Main Control Module
(2) Status indicator (3) AIDI_1 (4) AIDI_2 (5) COM1/AIDI_4 (6) COM3/12V (7) WAN1 (8) LAN1/POE (9) LAN2/POE (10) WAN2 (11) COM4/CAN (12) COM2/AIDI_5 (13) AIDI_3 (14) DO/12V (15) RF_Z (16) WLAN Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 57 ● Four RS485 ports with the default communications rate of expansion 9600 bit/s ● COM1–COM3 ports provide 12 V DC power. ● The power supply can be switched on or off and is on by default. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 58 ● The prerequisite for using a SIM card is that the site has signal coverage. ● Due to the performance limitation of the wireless module, China Telecom SIM cards are not supported. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 59 3G/4G EIRP power 23 dBm (max.) Communications Ports The ECC800-Pro provides the following communications ports. Figure 3-16 shows the pins of the RJ45 port. Figure 3-16 RJ45 port pins Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 60 Pin 7 Pin 8 Indicator Green Power output indicator indicator ● Steady on: The 12 V DC output is normal. ● Off: No 12 V DC output is provided. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 61 ● Pin 6 and Pin 7 collect sensor data. Pin 7 can detect current type sensors (4–20 mA). Pin 6 and Pin 7 can detect the output status of passive dry contact type sensors. Pin 3 and Pin 7 can detect temperature sensors. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 62 ● Steady on: The 12 V DC output is normal. ● Off: No 12 V DC output is provided. Table 3-25 USB port pin definitions Item Description Pin sequence Pin 1 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 63 Blinking at A network is set up, and super node access is allowed (the short indicator blinks at 10 Hz, on intervals for 0.05s and then off for 0.05s). Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 64: Environment Monitoring System
3.4.3.2 Environment Monitoring System 3.4.3.2.1 Electrode Water Sensor The electrode water sensor with the BOM number of 33010444 contains electrode probes and cables. Figure 3-17 Electrode water sensor Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 65: T/H Sensor
Figure 3-19 RJ45 port pins Table 3-29 RJ45 port pin definitions Description Pin1 or Pin4 Pin2 or Pin5 Pin 3 Pin 6 or Pin 8 V– Pin 7 Disconnected Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 66: Smoke Detector
Operating temperature –10°C to +55°C Ambient humidity ≤ 95% RH Dimensions (H x W x D) 31 mm x 75 mm x 51 mm (with the base) Weight 50 g Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 67: Video Management System
Wide dynamic range 120 dB Focal length 2.8–12 mm Video compression H.265/H.264/MJPEG standard Maximum resolution 1920×1080 Power supply 12 V DC, PoE IP rating IP67 Vandal resistant rating IK10 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 68: Ivs1800
Platfo 64 cameras to one 64 cameras to 16 cameras to 64 cameras to camera IVS1800 one IVS1800 one IVS1800 one IVS1800 perfor manc connect Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 69 Power 100–240 V AC; 200 W 100–240 V AC; 200 W 110–220 V AC; 200 W supply Weight 6.60 kg 6.70 kg 6.60 kg (hard disks excluded) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 70: Pad
Weight (with About 460 g About 468 g the battery) Touchscreen 10.1-inch, 1920 x 1200 10.4-inch, 2000 x 1200 resolution, IPS screen, and resolution, IPS screen, and multi-touch multi-touch Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 71: Cabinet Electronic Clasp Lock
(2) DIP switch (3) RJ45 power port Table 3-36 RJ45 port definitions Pin Description Description RS485+ RS485+ RS485– RS485– +12 V power supply +12V DC RS485+ RS485+ RS485– RS485– Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 72 (blinking at 10 Hz, on for interv 0.05s and then off for 0.05s). The cycle lasts for Alarm Stead A system failure alarm is indicator y on generated. The system is normal. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 73: Door Status Switch
Open-circuit voltage 100 V DC (maximum) Contact withstand voltage 150 V DC (maximum) Impedance 0.3 ohm Switch status Normally open Outer material White acrylonitrile butadiene styrene (ABS) engineering plastic Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 74: Optional) Uim20A Expansion Module
Table 3-39 UIM20A expansion module specifications Item Specifications Width 120 mm Depth 200 mm Height 43 mm Operating –30°C to +65°C temperature Installation Installed in a 19-inch rack requirement Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 75 The following table describes the pin assignment for ports COM1/AIDI_1 to COM8/AIDI_8. Table 3-41 Pin assignment for ports COM1/AIDI_1 to COM8/AIDI_8 Item Description Pin 1 RS485+ sequence Pin 2 RS485– Pin 3 Pin 4 RS485+ Pin 5 RS485– Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 76 Hz), on for 1s and then off for 1s). Blinking The communication is interrupted or the ECC800-Pro is fast unsuccessfully registered (blinking at 2.5 Hz, on for 0.2s and then off for 0.2s). Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 77: Wifi Module
ECC800-Pro. Figure 3-28 WiFi module Table 3-45 Technical specifications of a WiFi module Item Specifications Wireless IEEE 802.11n, IEEE 802.11g, and IEEE 802.11b standard Frequency band 2.4–2.4835 GHz Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 78: Wlan Antenna
A WLAN antenna can be connected only to the WLAN port on the main control module (02312QAA-004) to provide WiFi signals for devices such as the PAD to exchange data with the ECC800-Pro. Figure 3-29 WLAN antenna Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 79: Neteco
Standard network management interface: The NetEco provides SNMP interfaces to communicate with third-party network management systems (NMSs). The system can be customized to support other protocols for the access from different devices. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 81: Surge Protection And Grounding System
Each equipotential cable has a minimum cross-sectional area of 6 mm 3.6 Fire Extinguishing System A rack-mounted integrated fire extinguishing module can be configured for the cabinet. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 82: Integrated Cabling System
A cable tray is used inside a cabinet to route cables from the front to the rear. Cable Tray A cable tray is used for forward and backward cabling. It uses mounting ears to facilitate device installation. Figure 3-30 Cable tray Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 83 User Manual (02116410, 02116411, 021164112) 3 System Architecture Table 3-50 Cable tray technical specifications Dimensions (H x W x Weight Space Occupied 43.6 mm x 482.6 mm x 1.89 kg 250 mm Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 84: Installation Guide
Table 4-1 General tools and instruments Name, Specifications, and Appearance Protective gloves Marker Steel measuring Level tape Step ladder Phillips insulated Flat-head Adjustable torque torque insulated torque wrench screwdriver screwdriver (M6/M8) (M6/M8) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 85 Electrician's knife Impact tool Heat gun Needle-nose Diagonal pliers RJ45 crimping Insulation tape pliers tool Wire stripper Hydraulic pliers Wire clippers Crimping tool Multimeter Electroprobe Heat shrink Cable tie tubing Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 86 Flashlight Hacksaw Manual pallet truck Antifreeze gloves Cutter Welding torch Silver welding rod Oxygen cylinder Acetylene Hot melt device Clamp meter Pipe bender Insulated gloves Pressure gauge Rubber hose Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 87: Installation Environment Check
Allowed deviation: 3 mm/2000 □ Passed □ Failed Equipment room ≥ 2.6 m □ Passed □ Failed net height Equipment room □ Passed □ Failed ≥ 10.15 m area Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 88 Condensate drain outlet: Drains □ Passed □ Failed condensate from the smart cooling product. Figure 4-1 Space requirements NO TE If the requirements are not met, contact technical support. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 89: Site Equipment Preparation
Then pry off the top cover along the external edge of the cover until the cover can be taken out from the crate. ● Be careful to prevent your hands from being hurt by nails during unpacking. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 90: Installation Scenarios
4.1.4 Installation Scenarios Cabinet Internal Layout Figure 4-2 Cabinet internal layout (02116410) Table 4-5 Cabinet components (02116410) Component ECC800-Pro Door status sensor Power distribution subrack Lithium battery Water sensor Smoke detector Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 91 4 Installation Guide Component T/H sensor rPDU Figure 4-3 Cabinet internal layout (02116411) Table 4-6 Cabinet components (02116411) Component ECC800-Pro Power distribution subrack Electronic clasp lock Lithium battery Integrated air conditioner Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 92 4 Installation Guide Component Water sensor Smoke detector T/H sensor (10) rPDU Figure 4-4 Cabinet internal layout (02116412) Table 4-7 Cabinet components (02116412) Component ECC800-Pro Power distribution subrack Electronic clasp lock Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 93: Configuration Scenario
Not Onsite or Not ECC800-Pro Power distribution subrack UPS2000-H-6 Lithium battery rPDU 4G antenna WiFi module Smoke detector T/H sensor NOTE Cables have been laid out. Door status sensor Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 94 The monitoring rPDU needs to be commissioned onsite. UIM20A 4G antenna WiFi module Smoke detector T/H sensor NOTE Cables have been laid out. Electronic clasp lock Water sensor Camera Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 95 UPS2000-H-6 Lithium battery Transformer Smart cooling product rPDU 4G antenna WiFi module Smoke detector T/H sensor NOTE Cables have been laid out. Electronic clasp lock Water sensor Camera IVS1800 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 96: Personnel Requirements
Unpack and inspect all cabinets, mechanical parts, and components. Check that all the items are intact and comply with the packing list in the presence of both the project supervisor and customer. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 97 After checking that the cabinet is intact, remove the screw assemblies that secure the cabinet to the pallet, as shown in Figure 4-5. NO TICE Set the screw assemblies aside for they will be used in installation steps. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 98 After checking that the Converged Cabinet is intact, remove the L-shaped brackets that secure the cabinet to the pallet. Open the front and rear doors of the cabinet, and remove the cabinet lower sealing plates. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 99 Figure 4-7 Removing the L-shaped brackets Figure 4-8 Installing the cabinet lower sealing plates NO TE The middle two screws in the cabinet rear are used to secure the latch. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 100: Installing A Cabinet
Context To position a cabinet, perform the following steps: Determine the position of the cabinet based on the engineering layout diagram. Place the cabinet at the correct installation position. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 101 Put a level at the bottom of the cabinet in width and depth directions and check that the air bubble is in the middle between the two lines marked on the glass tube. Figure 4-10 Leveling a cabinet ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 102: Installing Smart Cooling Product Components
Step 2 Use an electrician's knife to cut a cross in the middle of the rubber plug for the water pipe hole at the bottom of the cabinet. Figure 4-12 Cutting the rubber plug Step 3 Route the drainpipe. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 103: Installing Remote T/H Sensors For The Smart Cooling Product
Open the front and rear doors of the cabinet. Unpack two T/H sensors and attach them to the cabinet posts. NO TE The installation positions of the T/H sensors can be adjusted as required. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 104: Installing Power Supply And Distribution Devices
Table 4-11 DIP switch settings on T/H sensors Address DIP Switch Sequence No. NO TICE The default address of T/H sensors purchased from Huawei is 1. Step 3 Insert the pre-routed cables into the ports on the T/H sensors on the front and rear door.s ----End 4.2.4 Installing Power Supply and Distribution Devices...
Page 105 ● One lithium battery occupies 3 U space. Procedure Step 1 Push a lithium battery into the cabinet and secure it. Figure 4-14 Installing a lithium battery Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 106: Optional) Installing Busbars
Procedure Step 1 Install busbars. Open the cabinet rear door. Install floating nuts at the busbar installation position. Secure the busbar to the installation position using screws. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 107: Installing Rpdus
16 U and 18 U positions at the rear of the cabinet. Procedure Step 1 (Optional) Open the rear door of the cabinet and install floating nuts in the rPDU installation position. Step 2 Secure the rPDU using screws. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 108 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 4 Installation Guide Figure 4-16 Installing a full-height vertical rPDU (02116410) Figure 4-17 Installing a horizontal non-intelligent rPDU (02116411 & 02116412) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 109: Installing Monitoring Devices
This step describes only the installation method. The actual appearance and cabinet interior layout may vary. ----End 4.2.5 Installing Monitoring Devices 4.2.5.1 Device Layout Figure 4-19 Monitoring device layout NO TE You can adjust the installation position based on site requirements. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 110: Installing The Sim Card And Antenna
Route the 4G antenna and WLAN antenna cables into the cabinet through the signal cable hole at the top of the cabinet and then to the appropriate ports on the ECC800-Pro. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 111: Installing A Pad
Connect the 4G antenna and WLAN antenna cables to the antenna ports on the ECC800-Pro. Figure 4-23 Installing an antenna cable ----End 4.2.5.3 Installing a PAD Context The PAD needs to be installed on the door of the Converged Cabinet. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 112 Step 2 Remove nuts from the PAD support, insert the support into the mounting holes on the cabinet front door, and reinstall the nuts to secure the support to the front door. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 113 Connect the delivered power cable and extension cable to the PAD support, bind the redundant cables to the PAD, and connect the power cable to the charging port on the PAD. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 114 Figure 4-28 PAD cable routing (cabinet rear door) (1) PAD power cable (2) L cable (3) Socket converter (4) PAD adapter (5) N cable Figure 4-29 PAD cable routing (cabinet front door) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 115: Installing Cabinet T/H Sensors
2 and that of the T/H sensor on the rear door to Table 4-13 DIP switch settings on T/H sensors Address DIP Switch Sequence No. Step 3 Insert the pre-routed cable into the port on the T/H sensor. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 116: Installing An Electrode Water Sensor
Figure 4-30 Routing a signal cable NO TE This step shows only the cable route. The actual cabinet layout may vary. ----End 4.2.5.6 (Optional) Installing a UIM20A Expansion Module Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 117: Optional) Installing A Server
Figure 4-32 Installing a UIM20A expansion module ----End 4.2.5.7 (Optional) Installing a Server Procedure Step 1 Determine the installation position of the server and check whether floating nuts are installed. If not, install them first. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 118 Step 4 When the two mounting ears on the server contact the mounting bars on the rack, tighten the captive screws on the mounting ears to secure the server. Figure 4-35 Installing a server Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 119: Optional) Installing A Camera
----End 4.2.5.8 (Optional) Installing a Camera Prerequisites ● A camera and tools for installing it have been prepared. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 120 Figure 4-38 Removing the transparent cover Gently insert the SD card into the SD card slot. Figure 4-39 Installing an SD card Step 2 Route the camera cable through the top of the cabinet. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 121 Figure 4-41 Installing the camera mounting plate Step 5 Use an insulated Phillips screwdriver to loosen the screws on both sides of the lens, adjust the surveillance angle, and tighten the screws to 0.6 N·m. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 122 LAN2/POE port on the ECC800-Pro. NO TE Other cables of the camera do not need to be connected but should be insulated. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 123: Optional) Installing A Lan Switch
Step 4 Connect a port on the LAN switch to the WAN1 port on the ECC800-Pro using a network cable. Step 5 Insert a power module into the power slot of the LAN switch, and tighten the captive screws on the power module panel. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 124: Installing An Ivs1800
Before the installation, ensure that the fastener of the hard disk tray is on a different side from the hard disk port, as shown in the lower left figure. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 125 0–3 to hard disks on the lower-layer hard disk tray and ports 4–7 to hard disks on the upper-layer, as shown in the lower left figure. Figure 4-50 Connecting data and power cables to hard disks Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 127 When the device is near the front door of the cabinet, fasten screws in hole groups 1 and 2; when the device is near the rear door, fasten screws in hole groups 2 and 3. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 128: Optional) Installing A Rack-Mounted Integrated Fire Extinguishing Module
For the 02116411 or 02116412 cabinet, configure a rack-mounted integrated fire extinguishing module. ● If no cable tray is installed above lithium batteries, install the rack-mounted integrated fire extinguishing module at the 1 U position above the lithium Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 129: Cable Routing
Find the corresponding cable based on the wiring diagram in the cable fitting bag, and attach the corresponding cable label taken out from the cable fitting bag to both ends of the cable by wrapping the ends. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 130 Keep a large number of cables neat and appealing in a cabinet by using cable organizers. Move the excess parts of cables in unnoticeable positions, as shown in Figure 4-60. Figure 4-60 Cable organizer Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 131 Reserve slack at cable connection positions to facilitate connection and disconnection and to prevent stress. Do not leave the cables tight and prevent connector misalignment, as shown in Figure 4-62. Figure 4-62 Cable connection positions Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 132 Bind cables with a moderate force and ensure that cables are not misshapen to prevent compromising the signal quality. After binding cables, cut off the excess parts of cable ties and trim away any burrs, as shown in Figure 4-64. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 133: Grounding The Smart Module
Figure 4-66. Figure 4-66 Direction for securing cable ties 4.3.2 Grounding the Smart Module Connect the ground point in the cabinet to the main ground bar. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 134: Cable Connections To The Power Supply And Distribution System
Figure 4-67 Cabinet main copper bar for grounding (02116410) Figure 4-68 Cabinet main copper bar for grounding (02116411 & 02116412) 4.3.3 Cable Connections to the Power Supply and Distribution System Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 135: Cable Routing Description
Wire bushings are installed at the cable outlets of the cabinet for ease of cable routing. Cut a cross in the middle of a wire bushing using an electrician's knife, as shown in Figure 4-71. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 136: Connecting Cabinet Input Power Cables
(Optional) Remove the transparent protective panel at the rear of the PDU. Connect input power cables to the PDU. Figure 4-72 Connecting input power cables to the PDU (02116410) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 137: Connecting Rpdu Cables
● Connect cables to the rPDU based on the type of the rPDU and the silk screen on the wiring port. The following cable connection is for reference only. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 138 Figure 4-74 Connecting rPDU cables Step 2 Take out the rPDU cables and connect the cord end terminals of the power cables to the ports in the power distribution subrack. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 139 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 4 Installation Guide Figure 4-75 Connecting power cables to a full-height vertical non-intelligent rPDU (02116410) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 140: Connecting Rpdu Signal Cables
If the cabinet is equipped with an intelligent rPDU, refer to this section. Procedure Step 1 Connect the LAN1 port on the ECC800-Pro to the PoE port on the UIM. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 141: Connecting Lithium Battery Cables
Step 1 Connect lithium battery power cables. Connect the positive battery terminal to the RTN+ port on the busbar and the negative battery terminal to the –48 V port on the busbar. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 142 4 Installation Guide Figure 4-78 Connecting cables between lithium batteries and busbars Connect cables between the busbars and the PDU. Figure 4-79 Connecting cables between the busbar and the PDU Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 143: Connecting Ivs Cables
Step 1 Connect one end of the ground cable to the ground terminal on the device and the other end to the ground point on the cabinet. An insulated Phillips screwdriver and M4 screws are required. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 145: Verifying The Installation
□ Passed □ Failed cable joints between network cables. Exposed parts near the wiring terminals and lugs □ Passed □ Failed are wrapped in PVC insulation tape or heat shrinking tubing. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 146 Lithium batteries are intact, free from damage, □ Passed □ Failed cracks, and bulges. Lithium batteries are neat and clean, and do not □ Passed □ Failed leak electrolyte. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 147 □ Passed □ Failed from damage, break, and acid leakage. Lithium battery cables are connected correctly. □ Passed □ Failed DIP switches on devices are correctly set. □ Passed □ Failed Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 148: Power-On Commissioning
Step 4 Switch on the UPS input circuit breaker. Step 5 After the UPS starts, set parameters based on site requirements, start the inverter, and switch on the UPS output circuit breaker. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 149: Ups Power-On Commissioning
Do not press any button during inverter startup. When the startup command is successfully delivered, and the inverter indicator is steady on, the UPS enters normal mode. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 150 Figure 5-2 Powering on/off the UPS on the app Method 3: On the WebUI, choose Monitoring > UPS System > Running Control to start the UPS. Figure 5-3 System Commands & Tests Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 151: Starting A Ups
Step 4 Select a startup method to start the UPS in normal mode. For details, see the section "UPS Startup Method." Step 5 When the UPS runs properly, switch on the UPS AC output circuit breaker Q1 to supply power to loads. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 152: Ups Shutdown Method
Step 4 Switch off the mains AC input circuit breaker K1 and output circuit breaker Q1 of the UPS. After all indicators turn off and fans stop, the UPS shuts down, and the loads power off. ----End 5.1.1.6 Cold-Starting the UPS Using Batteries (Single UPS) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 153: Connecting The Lithium Battery Supply
Step 4 Observe the lithium battery for 15 mins. Ensure that it is working properly (the ALM indicator is off and the RUN indicator is steady on). ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 154: Power-On Commissioning For The Cooling System
5.2.2 Initial Configuration You need to log in to the management system before configuring the cooling system which is commissioned and managed through the ECC800-Pro. 5.2.2.1 Preparations and Management System Login Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 155: Preparations And Webui Login
Step 3 Set the LAN. (Optional) Open the Chrome browser, go to the Settings page, choose System, click Open your computer's proxy settings, and deselect Use a proxy server. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 156: Preparations And App Login
----End 5.2.2.1.2 Preparations and App Login Prerequisites App operating environment requirements: ● The mobile device runs Android 4.0 or later or HarmonyOS, and the operating system is not rooted. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 157 Before the installation, ensure that the PAD is connected to the Internet and the network is running properly. ● Huawei AppGallery installed on the PAD Log in to the Huawei AppGallery client, search for FusionModule, and tap Install. ● Huawei AppGallery not installed on the PAD...
Page 158 Enter the password currently used for logging in to the WebUI and click Submit. Specify WiFi SSID and WiFi Password and click Submit to change the SSID and password. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 159: Initial Startup Password Authentication
WiFi SSID specified on the WebUI, and enter the value of WiFi Password specified on the WebUI for login. If the Huawei PAD fails to connect to the WiFi network automatically after the WiFi network is restarted, on the settings screen, choose WLAN > More Settings to disable WLAN+ or choose WIFI >...
Page 160: Optional) Imanager-M Service Access
Disable of Mobile data control to Enable. Choose System Settings > NMS Application > NetEco1 Communication Parameters and select iManager-M for Service type. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 161: Performing Initial Configuration
FusionCol5000, and the other end has been connected to the COM2 port on the ECC800-Pro. Procedure Step 1 Add the FusionCol5000-A0031. Log in to the ECC800-Pro WebUI as an administrator. Adding the FusionCol5000-A0031 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 162 Cold aisle T/H sensor fault enable and Hot aisle T/H sensor fault enable to Enable. On the Controls tab page, set the smart cooling product control parameters (such as on/off control parameters). Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 163: Commissioning The Cooling System
R410A Saturation Gauge Saturation Gauge Saturation Gauge Temperatu Pressure Temperatu Pressure Temperatu Pressure re (°C) (MPa) re (°C) (MPa) re (°C) (MPa) 1.31 2.21 0.73 1.35 2.27 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 164 Changeme). To enter the diagnostic mode, log in as user admin. Procedure Step 1 Log in to the ECC800-Pro WebUI as user admin. Choose Monitoring > Cooling > FusionCol5000-A0031. The page for commissioning smart cooling products is displayed. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 165: Management System Power-On Commissioning
Step 2 After you add a device based on the site requirements or click Auto Discover Device, the details about the device connected to the smart module are displayed. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 166: Creating A Smart Module Plan View
Step 2 Choose Home > Plan View, create a smart module in Smart Module View and set the layout and device quantity based on the actual smart module scenario. Figure 5-7 Creating a view Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 167 No need to lay out the smart module view. Half-size cabinet Each cabinet has two configuration positions. Number qty./row of half-size cabinets in each row = Number of cabinets x 2 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 168: Commissioning Sensors
5.3.4.1 Setting and Adding a Smoke Detector If a smoke detector is installed, perform the following steps to configure it. Context If the detector is prefabricated, only check its settings. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 169: Commissioning A T/H Sensor
Operate the DIP switch on the T/H sensor to set the device address for the sensor. Toggle switches 1 to 6 specify the device address in binary mode. ON indicates 1, and OFF indicates 0. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 170 During actual configuration, set the device address for the T/H sensor based on the actual situation. Click Test Connect to check whether the T/H sensor connects to the ECC800- Pro properly. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 171: Commissioning An Electrode Water Sensor
The specific alarm then can be reported. ● If the sensor is preinstalled, only check its settings. ● The actual value may vary. Only the method of the parameter settings is described. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 172: Commissioning A Cabinet Electronic Clasp Lock
Step 2 (Optional) If the cabinet door still cannot be opened after step 1 is performed, adjust the position of the cabinet electronic clasp lock by using the slotted holes until the cabinet door can be opened and closed properly. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 173 Step 4 Add the cabinet electronic clasp locks. Log in to the ECC800-Pro WebUI as an administrator. Create a cabinet view in Smart Module View on the home page. Add a cabinet electronic clasp lock. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 174 Global lock cabinet > informati Cabinet Electronic Clasp Lockn. Change Click the Change the cabinet electronic Running clasp lock name. cabinet Parameters tab. electroni c clasp lock name. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 175 Check whether there is interference between the lock tongue and the cabinet column. If so, adjust the installation position of the lock tongue. Figure 5-13 Adjusting the position of a lock tongue Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 176: Commissioning A Cabinet Door Status Sensor
Choose Monitoring > System > ECC800 > Running Parameters > AI/DI_2 Port Settings. Set Door1 sensor to Enable and click Submit. Set Door1 sensor type to Door sensor and click Submit. Step 2 Check the door status sensor functions. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 177: Commissioning An Intelligent Rpdu
Number of connected devices list. – If the connection is abnormal, check whether the cable is properly connected to the device, whether the device is running properly, and Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 178: Configuring Event Notification
If Test email sending failed is displayed, check whether the receiver's mailbox server requires CA certificate verification. If it is required, download the CA certificate from the receiver's mailbox website and upload it in the Mailbox Certificate area. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 179 5 Power-On Commissioning Figure 5-15 Mailbox setting page NO TE The following mailbox addresses are for reference only (the actual parameters apply) and are used only for configuring the email function. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 180 The email address is used only for configuring the email function and is not used for other purposes. The address is encrypted during transmission in the ECC800-Pro to ensure that the personal data of users is fully protected. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 181 The mobile phone number is used only for configuring the SMS function and is not used for other purposes. The phone number is encrypted during transmission in the ECC800-Pro to ensure that the personal data of users is fully protected. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 182 Check whether the mobile phone number is correctly set. Step 5 Set the alarm notification delay time and add alarm notification parameters. Figure 5-18 Setting the alarm notification parameters Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 183 If an error code is not listed in the following table, provide the ECC run log and contact the customer technical support. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 184 2. Check whether the service port of the email server is enabled. Check whether the email server is running properly and whether the service port is started properly. Check whether the email server is running properly. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 185 Contact the personnel of the third-party mail server to add the sender address to the whitelist and do not limit the sending rate. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 186: Linkage Control
● If the rear door of the cabinet is open and the temperature in the cold aisle is higher than the preset value (35°C by default), the front door of the cabinet automatically opens. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 187: Linking The Smoke Alarm With Cabinet Electronic Clasp Lock Open
Step 1 Log in to the ECC800-Pro WebUI as an administrator. Step 2 Choose System Settings > Linkage Control. Step 3 Ensure that Enable linkage control function is Yes. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 188: Linking The Fire Control With Cabinet Electronic Clasp Lock Open
Select Link fire control with clasp lock open under Linkage Group. If its value is on, the corresponding logic configurations under Linkage Logic List are available. If its value is off, the corresponding logic configurations under Linkage Logic List are unavailable. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 189: Linking The Emergency Ventilation With Cabinet Electronic Clasp Lock Open
Select Link emergency ventilation with clasp lock open under Linkage Group. If its value is on, the corresponding logic configurations under Linkage Logic List are available. If its value is off, the corresponding logic configurations under Linkage Logic List are unavailable. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 190: Commissioning A Camera (Lan Switch Networking Scenario)
IE mode button in the upper right corner of the page to log in. To use the IE mode, click the IE mode button on the toolbar. Figure 5-20 IE mode button Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 191 IPv4 address Method for obtaining the IP address. The options are assignment Obtain IP address automatically and Use the following IP address. The default value is Obtain IP address automatically. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 192 Secondary DNS Secondary DNS IP address. The default value is 0.0.0.0. Set the camera stream type and primary stream parameters. Path: Configuration > Video/Audio > Video. See the following figures. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 193 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 5 Power-On Commissioning Figure 5-22 Setting primary stream parameters Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 194 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 5 Power-On Commissioning Figure 5-23 Setting secondary stream 1 parameters Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 195 High profile. Among these profiles, the baseline profile has the lowest encoding compression performance and lowest requirements on hardware decoding performance, while the high profile has the highest. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 196 H.264 or H.265 and Bit rate type to Variable bit rate. Better image quality requires higher bandwidth. Therefore, select proper image quality based on the site requirements. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 197: Commissioning A C3220 Camera (Sd Card Configured)
The camera IP address must be unique and set to the actual value. Procedure Step 1 Log in to the Huawei camera WebUI. Configure the PC IP address and the camera IP address in the same network segment. Enter the camera IP address (192.168.0.120 by default) in the address bar of the browser and press Enter.
Page 198 Choose Configuration > Storage > Storage Management. The Storage Management page is displayed. Format the SD card. Set the camera stream type and primary stream parameters. Path: Configuration > Video/Audio > Video. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 199 User Manual (02116410, 02116411, 021164112) 5 Power-On Commissioning Figure 5-25 Setting video and audio stream parameters NO TE If longer-time video storage is required, set camera parameters according to the following table. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 200 Figure 5-26 Motion detection Configure the device alert deployment and alarm linkage policy. Choose Configuration > Service > Alarm Service, click Common Alarm, and configure Device Alert Deployment and Alarm Linkage Policy. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 201: Optional) Commissioning The Ivs1800
5.3.11.1 Setting Parameters on the IVS1800 WebUI Context A default IP address has been configured for the IVS1800 before delivery. Modify the IP address based on the actual network plan. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 202 Step 4 Configure disk initialization. NO TE Recording data can be stored only after you install and initialize the disks. Choose Storage > Disks and click Forcibly Format. Configure disk initialization. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 204 Change the PC IP address to an address in the network segment of the new IVS1800 IP address, enter the IVS1800 IP address in the address box of the Internet browser, and log in to the OMU portal system. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 205 NAT mapped port number configured on the firewall. Click Save. Figure 5-32 Setting the port number Set other parameters based on the site requirements by referring to the preceding steps. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 206 NTP server IP Indicates the IP address of the NTP clock source server. After this parameter is specified, the server synchronizes the time to this clock source. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 207: Setting Parameters On The Iclient S100
The network communication between the IVS1800 and the camera is normal. ● The network communication between the PC where the iClient S100 is installed and the device is normal. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 208 – Download the latest version of iClient S100, and install and commission it by referring to the iClient S100 user manual of the corresponding version. – Use your mobile number to register a Huawei Cloud account, complete real-name authentication, and then log in to the HOLOWITS.
Page 209 By default, the system scans all disks, locates the disk with the largest available space, and creates the SecurityDBBack folder. You can also click Browse to specify the path for storing the backup files. Step 8 Click Install to start the installation. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 210 If you select this option, the password of the user used for the last password login is saved. Forgot If you have bound your account to an email address, you can password retrieve your password using your email address. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 211 Specifies the type of the device to add (IVS1800). Name Specifies the device name. Address Specifies the device address. The format is xxx.xxx.xxx.xxx, for example, 192.168.1.10. Port Specifies the device port. The default port number is 18531. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 212 Click Next to search for cameras. (Optional) Click Stop to stop the search. Table 5-28 Parameter description Parameter Setting Drive Select HWSDK. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 213 Camera web system Set connection ONVIF parameters. Adding cameras to a Maintenance Add cameras to a group group Management > Video to facilitate camera Device > Group Device management. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 214: How Do I Troubleshoot The Failure To Find A Camera On The Iclient S100
I am adding a camera through Search Access, the system stays at the Searching for cameras page for more than 1 minute and cannot discover the camera. Figure 5-35 Selecting a mode to add cameras Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 215 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 5 Power-On Commissioning Figure 5-36 Searching for cameras Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 216 User Manual (02116410, 02116411, 021164112) 5 Power-On Commissioning Troubleshooting Process Figure 5-37 Troubleshooting flowchart Procedure Step 1 Check whether the network between the iClient and the IVS1800 is bidirectionally connected. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 217 – If the test succeeds, go to Step Step 2 On the IVS1800, choose System > Network Configuration to check whether the value of Gateway IP Address is 192.168.248.10. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 218 If no, go to Step Step 4 Re-subscribe to the IVS or cameras. ● If at least one camera has been added, you can cancel subscription and then re-subscribe to it. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 219 Step 6 If the fault persists after the restart, you are advised to add a camera through IP Access. NO TE You can view the camera IP address on the ECC800-Pro. If an old camera is to be connected, set the Device Login Port to 6060. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 220 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 5 Power-On Commissioning Figure 5-42 IP access Figure 5-43 Viewing the camera IP address Figure 5-44 Device login port ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 221: Optional) Neteco Management
● In this scenario, the MAC addresses of the WAN1 and WAN2 ports are the same by default. You need to configure a static route for the WAN2 by referring to the method of configuring dual MAC addresses and static routes. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 222 Step 5 Tighten the screws on both sides of the panel of the ECC800-Pro main control module. Step 6 Install a 4G antenna. Figure 5-48 Installing a 4G antenna ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 223: Setting Neteco Parameters
Submit. Settings > control System Paramete rs > Mobile Data. Step 3 Click Submit. Step 4 Set NetEco communications parameters and authentication password on the ECC800-Pro WebUI. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 224: Obtaining The Neteco Software License
5.3.12.3 Obtaining the NetEco Software License The NetEco software license is not provided together with software to the customer. Therefore, obtain the NetEco software license in advance. Obtain the license from the Huawei's enterprise support website. ● For enterprise users: Log in to Huawei's enterprise support website https:// support.huawei.com/enterprise.
Page 225: Obtaining The Adapter Software Installation Packages
OpenPGP Signature Verification Guide . If the software package according to the fails to pass the verification, do not use the software package and contact Huawei technical support. Before a software package is used in installation, its digital signature also needs to...
Page 226: Powering On A Server
Figure 5-50 TaiShan 200 server power button ----End 5.3.12.6 Logging In to the NetEco Client This section describes how to log in to the NetEco client using a web browser. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 227: Loading The Neteco Software License
Step 1 Click Import License file when you log in to the NetEco at the first time. Step 2 Click next to the License text box and select a license file. Step 3 Click Upload. The information about the imported license file is displayed. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 228: Installing Ne Adapters
● The NetEco is preconfigured with management domains such as cabinets, battery cabinets, buildings, containers, floors, FusionModule500, smart modules, NetEco sites, parks, PDUs, equipment rooms, and subnets. To use more management domains, you need to install the corresponding adapter software package on the NetEco.
Page 229: Example: Adding A Smart Module
Step 4 In the Domain area on the lower left of the page, select Modular from the drop- down list box. Step 5 Select the Modular to be added and drag the modular icon to the management domain area. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 230 Step 6 Modify Management Info of the smart module as required or retain the default values. Step 7 Click on the toolbar to save the settings. ----End Follow-up Procedure Perform the following operations on the Planning Configuration page as required. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 231 Parent Name and Control Type, and you do not need to manually set them, you only need to set Name. 4. In the upper area of the current page, click Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 232: Creating An Ecc800-Pro On The Neteco
Information in the displayed window. 5.3.13 (Optional) Third-party NMS Management (over SNMP) 5.3.13.1 Connecting a Communications Cable Procedure Step 1 Connect a communications cable to the WAN1 port on the ECC800-Pro. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 233: Setting Snmp Management Parameters
NMS. These parameters are required for setting up the ECC800-Pro on the NMS. ● SNMPv1 and SNMPv2c are insecure. Therefore, SNMPv3 is recommended. This section uses SNMPv3 as an example. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 234 10. After setting the parameters, click Confirm. 11. Click Export in the Mib File pane, export the MIB file, and send it to the development engineers of the NMS. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 235: Optional) Imanager-M
Installing the App NO TE Currently, the NetEco app can be installed only on Android mobile phones. ● Obtaining the software installation package from the Huawei AppGallery and installing the app Go to Huawei AppGallery (https://appgallery.huawei.com) and search for NetEco.
Page 236: Optional) Replacing The App Certificate On A Mobile Device
5.3.14.1.2 (Optional) Replacing the App Certificate on a Mobile Device This section describes how to replace the preset security certificate in the NetEco app on a mobile device. Preset Huawei certificates apply only to commissioning scenarios. For security purposes, apply for certificates from the certification authority (CA) and use them to replace the preset certificates.
Page 237: Registering A Neteco App Account
NetEco app. ----End 5.3.14.1.4 Logging In to the NetEco App After the app is installed on a mobile device, you can log in to the NetEco server using the app. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 238: Connecting A Device
WiFi or mobile network. If the network is normal, check whether you have been forcibly logged out on the NetEco. If a Huawei phone is used, the push notification function is enabled for the NetEco app by default.
Page 239: Logging In To And Logging Out Of The Neteco Webui
5.3.14.2 Logging In to and Logging Out of the NetEco WebUI This section describes the operating environment requirements of the NetEco WebUI and provides guidance for users to log in to or log out of the NetEco WebUI. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 240: Operating Environment Requirements
Table 5-37 Operating environment requirements Confi Basic Configuration Requirements gurat Item I5-7500 or later 8 GB Oper Windows 10 Professional 64-bit ating syste Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 241 3. In the Pop-ups and redirects dialog box, click Add. 4. In the Add a site dialog box, enter https://server IP address:server port number (https://10.10.10.1:31943 for example), and click Add. 5. Close the Settings tab page. For Firefox: Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 242: Logging In To The Neteco Webui
NetEco WebUI for the first time. For details, see 5.3.14.3.2 What Do I Do If the Browser Displays a Certificate Error or Security Risk. Step 2 Enter the User Name, Password, and click Log In. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 243: Logging Out Of The Neteco Webui
You can enable or disable the real-time alarm notification function as required. Prerequisites You have logged in to the NetEco app. Procedure Step 1 Enable or disable the Push notifications function as required. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 244 4. Follow the onscreen instructions to enable the Push notifications function. NOTE ● If a Huawei phone is used, the Push notifications function is enabled for the NetEco app by default. ● If a third-party mobile phone is used, you need to manually enable the Push notifications function and ensure that the HMS Core process is not cleared.
Page 245: What Do I Do If The Browser Displays A Certificate Error Or Security Risk
Figure 5-58. ● When Mozilla Firefox is used to log in to the NetEco, the system displays a connection error message, as shown in Figure 5-59. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 246 Operations on the browser may vary depending on browser versions but are similar to the examples in the following steps. You are advised to perform the operations based on actual situations. ● Google Chrome: Click Advanced. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 247 Click I Understand the Risks, as shown in Figure 5-60. Figure 5-60 Clicking I Understand the Risks In the expanded area, click Add Exception, as shown in Figure 5-61. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 248: Fire Extinguishing System Power-On Commissioning
5.4 Fire Extinguishing System Power-On Commissioning Context After a fire extinguishing module is configured and installed, you can commission Procedure Step 1 Log in to the ECC800-Pro WebUI as an administrator. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 249 Step 3 Set Device type to ECC800 and Device name to System-ECC800, and click OK. Step 4 In the query result area, set the new signal name of AI/DI_2 to Fire extinguishing module and click Submit. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 250: Routine Maintenance
(MCB) red, replace ● The MCB is status. the surge switched on. protection module. ● If the MCB is off, switch it Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 251 2. The battery terminals are intact. 3. Batteries are free from damage and cracks. 4. Batteries are free from acid leakage. 5. Batteries are not deformed or bulged. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 252 Operating ● Ambient If the environment temperature: –20°C temperature or to +65°C humidity is abnormal, check ● Humidity: 0%–95% the smart RH (non- cooling product condensing) status. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 253 Cable connection The cable connection Secure loose is secure. cables. Cables are not Replace damaged. damaged cables. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 255: Quarterly Maintenance
LCD, all units the fault by are operating checking the properly. No device status fault or alarm and parameters. information is found in the active and historical alarm records. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 256 Lithium battery Battery No battery Identify the management management cause of an alarm alarm is alarm based on generated. the alarm information. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 257 Battery Check that the Set parameters management settings of correctly. parameter settings battery management parameters meet the requirements in the user manual. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 259 Operating ● Ambient If the environment temperature: temperature or –20°C to humidity is +65°C abnormal, check the smart ● Humidity: cooling product 0%–95% RH status. (non- condensing) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 260 Cable connection The cable Secure loose connection is cables. secure. Cables are not Replace damaged. damaged cables. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 261 The ambient Locate the the ambient temperature of cause of an temperature of the intelligent abnormal the intelligent battery temperature. battery monitoring monitoring system system is lower than 45°C. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 262: Yearly Maintenance
Tighten all bolts The bolts are Tighten a bolt if power cables and regularly using an secured. it is loose. the busbar adjustable wrench after powering off the device. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 264 Parameter Reset the configuration configuration of parameters. the output voltage grade, frequency, number of batteries, and battery capacity meets requirements. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 265 (charging); – operating 20°C to +45°C temperature. (discharging) 2. If the fault 2. Battery persists, charge and contact discharge technical conditions support. meet the requirements specified in the battery specifications. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 266 Huawei indicating tight technical connections does support. not change. Cables between No cable Replace the batteries deteriorates and faulty cable. the insulation layer does not crack. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 267 (recommended) discharge test an exception when the UPS is is identified. backed up to 2. If the fault verify that the persists, batteries can contact discharge technical properly. support. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 268 The torque meets requirements of the battery manufacturer. After checking that the battery screws meet requirements, mark the screws for later check. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 269 If the indicator module indicator module indicator is off or any is steady green abnormal or blinking condition green. occurs, see 6.2.2 Management System Troubleshootin to rectify the fault. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 270 Cable connection The cable Secure loose connection is cables. secure. Cables are not Replace damaged. damaged cables. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 271 The ambient Locate the the ambient temperature of cause of an temperature of the intelligent abnormal the intelligent battery temperature. battery monitoring monitoring system system is lower than 45°C. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 272: Troubleshooting
Turn ● The UPS is faulty. on the switch again, and check whether the system is overloaded. ● Restart the UPS. If the UPS is faulty, replace Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 273 UPS on the ECC800-Pro WebUI. The UPS does not report The output cable is not Check the output power a fault but has no output properly connected. cable connection. voltage. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 274 AC power supply incorrectly set. immediately. ● Verify that the number of batteries and battery capacity are correctly set based on the actual configuration. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 275: Management System Troubleshooting
1. Clean the connector (yellow) is blinking. failure in the rear of the faulty PSU. Monitoring module 2. If the fault persists, communication failure replace the ECC800- Pro subrack. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 276 AIDI_5, COM1– management system. COM4, and DO). The corresponding Check whether the power ports are short- connected load is circuited. short-circuited. If yes, eliminate the short circuit. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 277: Alarm References
Fan fault Critical The fan is abnormal. Clean up foreign matter around the fan. If the fault persists, contact technical support. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 278: Parts Replacement
● Check whether ground, resulting in battery loop cables electricity leakage. are deteriorated or broken, and replace faulty cables. 6.4 Parts Replacement Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 279: Replacing Structural System Components
● The mounting holes for the new cabinet electronic clasp lock are slotted holes. If the door cannot be properly closed after installation, adjust the lock height based on site requirements. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 280: Replacing A Gas Spring
Step 2 Remove the nuts from the gas spring using an adjustable wrench. Step 3 Remove the gas springs. Figure 6-2 Removing a gas spring Step 4 Tighten the new air spring using an adjustable wrench. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 281: Replacing Power Supply And Distribution System Components
Material: A new surge protection module of the same model is available and functional. Procedure Step 1 Switch the SPD circuit breaker to OFF. Step 2 Remove the protective panel from the SPD. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 282 Step 4 Hold the faulty surge protection module and pull it out, as shown in Figure 6-5. D ANGER During replacement, do not touch the energized components in the power distribution subrack. Figure 6-5 Replacing a surge protection module Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 283: Replacing A Fuse
Step 2 Reinstall the fuse terminal block in the power distribution subrack. Step 3 Close the fuse terminal block. Step 4 Observe the indicator. If the indicator is on, the fuse is functional. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 284: Replacing An Rpdu
Step 2 Switch off all circuit breakers in the cabinet and the mains input circuit breaker. NO TICE This step results in service interruptions. Step 3 Remove the EPO signal cable connected to the UPS, and then remove the cables of the transformer. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 285 Step 4 Remove the screws at the front of the transformer. Figure 6-7 Removing screws at the front of the transformer Step 5 Remove the screws at the rear of the transformer and pull out the old transformer. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 286 Step 11 Switch on the load circuit breaker. Step 12 Check whether the UPS generates abnormal alarms. If there is any alarm, clear it and start the UPS. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 287: Replacing A Ups2000-H
UPS, and whether all cables are connected. NO TICE Do not connect the manual bypass switch (MBS) signal cable to the UPS rear at present. Step 9 Start the UPS and set related parameters. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 288: Replacing A Lithium Battery
Step 7 Connect the cables to the new battery based on the cable labels. Step 8 Switch the BAT– battery circuit breaker in the power system to ON or reinstall the battery fuse using a fuse extracting unit. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 289: Replacing Cooling System Components
An internal circulation fan needs to be replaced. ● A spare internal circulation fan of the same model is available and functional. Context The fan is maintained from the top. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 290 Step 2 Disconnect the power supply from the smart cooling product control unit after the smart cooling product is shut down. Step 3 Remove the screws that secure the top panel using an insulated Phillips screwdriver, and remove the top panel. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 291 Step 7 Remove the sheet metal fastener bolts from the fan support using a socket wrench, remove the nuts from the fan using an adjustable wrench, and remove the fan. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 292: Replacing A Psu, Rectifier, Or Main Control Module
● A PSU, rectifier, or main control module needs to be replaced. ● A spare PSU, rectifier, or main control module of the same model is available and functional. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 293 This section describes how to replace a PSU. Software ● To replace the main control module, download the software and Upgrade Guide from Huawei websites, and upgrade it on the PAD or ECC800- Pro. ● Figure 6-12 shows the front panel of a smart cooling product control unit.
Page 294: Replacing An Ntc Temperature Sensor
An NTC temperature sensor needs to be replaced. ● A spare NTC temperature sensor of the same model is available and functional. Procedure Step 1 Shut down the smart cooling product. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 295: Replacing A Low Pressure Sensor
A low pressure sensor needs to be replaced. ● A spare low pressure sensor of the same model is available and functional. Context The low pressure sensor is maintained from the top. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 296 Step 11 Choose Controls > Control Information, set Diagnostic mode to Enter, and click Submit Step 12 Choose Running Parameters > Diagnostic Mode Parameters, set Comp manual control to 3000 rpm, and click Submit. Choose Running Info > Compressor Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 297: Replacing A Contactor
Step 3 Remove the cover from the electric control box using an insulated Phillips screwdriver, remove the cable from the contactor using a small-sized flat-head screwdriver, and remove the contactor, as shown in Figure 6-14. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 298: Replacing An Eev And Coil
A spare EEV and a coil of the same model are available and functional. Context ● The EEV and coil are maintained from the rear. ● The silk screen of the electronic expansion valve is EEV. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 299 Step 5 Weld the two ends of the EEV using a welding torch. Then, remove the EEV. Step 6 Weld a new EEV, and install the coil for the EEV. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 300: Replacing An External Circulation Fan
6.4.3.7 Replacing an External Circulation Fan Prerequisites ● An external circulation fan needs to be replaced. ● A spare external circulation fan of the same model is available and functional. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 301 Step 5 Remove the screw from the fan using a small wrench, and remove the external circulation fan blades, as shown in Figure 6-16. Figure 6-16 Removing the external circulation fan blades Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 302: Replacing A Compressor
A compressor needs to be replaced. ● A spare compressor of the same model is available and functional. Context ● Before replacing the compressor, disconnect the power supply and discharge refrigerant from the system. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 303 NO TICE To avoid burning the internal components, other pipes, thermal insulation foam, power cables, and labels, take protective measures, such as spreading wet cloth, around the welding position. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 304 Step 14 After powering on the smart cooling product, log in to the ECC800-Pro WebUI as user admin, choose Monitoring > Cooling > NetCol5000-A1 > Controls > Control Information, set Startup/Shutdown control to ON, and click Submit. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 305: Replacing A High Pressure Sensor
Method 2: Log in to the ECC800-Pro WebUI as user admin. Choose Monitoring > Cooling > NetCol5000-A1 > Controls > Performance Maintenance Control, and clear up the compressor total runtime. ----End 6.4.3.9 Replacing a High Pressure Sensor Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 306 Step 7 Apply sealant to the threads of the new high pressure sensor. Install a new high pressure sensor in the original position using an adjustable wrench and connect the cable. Step 8 Secure the high pressure sensor cable using cable ties. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 307: Replacing A Pneumatic Switch
(required based on local conditions), nitrogen injection and pressure preservation tool, vacuumization tool, refrigerant injection tool ● Preparation: Power off the outdoor unit and retrieve the refrigerant in the system. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 308 Step 11 After powering on the smart cooling product, log in to the ECC800-Pro WebUI as user admin, choose Monitoring > Cooling > NetCol5000-A1 > Controls > Control Information, set Startup/Shutdown control to ON, and click Submit. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 309: Replacing Management System Components
● Tools: ESD wrist strap, ESD gloves, insulated Phillips screwdriver, label, marker ● Materials: a new undamaged and undeformed ECC800-Pro main control module of the appropriate model Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 310 Step 6 (Optional) Remove the SIM card from the corresponding slot of the ECC800-Pro main control module. Step 7 (Optional) Install the removed SIM card in the corresponding slot of the new ECC800-Pro main control module. Figure 6-19 Installing a SIM card Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 311: Replacing An Ecc800-Pro Antenna
Step 1 Record the positions of the signal cables connected to the panel of the ECC800- Pro main control module, and then disconnect the signal cables. Step 2 Loosen the screws on both sides of the panel of the ECC800-Pro main control module. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 312 Step 7 Tighten the screws on both sides of the panel of the ECC800-Pro main control module. Step 8 Connect the signal cables to the panel of the new ECC800-Pro main control module based on the recorded information. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 313: Replacing A Camera
Step 1 Remove the transparent cover using an insulated Phillips screwdriver. Figure 6-24 Removing the transparent cover Step 2 Remove the SD card. Figure 6-25 Removing an SD card Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 314: Replacing An Ivs1800
A spare IVS1800 of the same model is available and functional. Context NO TICE Videos cannot be recorded during the replacement of the IVS1800. D ANGER Do not operate with power on. Take appropriate insulation measures. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 315: Replacing A Hard Disk For The Ivs1800
A spare hard disk of the same model is available and functional. ● Before replacing a faulty disk, ensure that the power switch on the rear panel is off and disconnect the power cable to power off the device. Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 317 Close the chassis cover, and use a PH2 screwdriver to fasten the rear screws. Figure 6-33 Closing the chassis cover Step 4 Observe the hard disk indicator to check whether the hard disk works properly. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 318: Replacing A T/H Sensor (33010516)
Step 5 Blow smoke toward the smoke detector using a smoke pistol until the smoke detector indicator changes from blinking once every 6s to steady on. If a smoke detector fire alarm is triggered, the smoke detector is functional. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 319: Replacing An Electrode Water Sensor
Step 4 Install the new door status sensor on the conversion bracket of the cabinet door, and connect cables to the sensor. Step 5 Reinstall the cover on the door status sensor. ----End Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 320: Technical Specifications
● Signal cables can be routed out from the top or bottom. Operating temperature Indoor: 0–40°C Outdoor: –20°C to +45°C Storage temperature –40°C to +70°C Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 321 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) 7 Technical Specifications Item Specifications Storage humidity ≤ 95% RH (non-condensing) Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 322: A Equipment Derating Coefficients
(sea level +15ºC). Table A-1 Derating coefficients of the UPS2000-H Altitude (Unit: m) Derating Coefficients 1000 1500 0.95 2000 0.91 2500 0.86 3000 0.82 3500 0.78 4000 0.74 4500 5000 0.67 Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 323: B Acronyms And Abbreviations
Auto Transformer Switch Equipment Battery Interface Module Communication Interface Module direct current International Electrotechnical Commission miniature circuit breaker SNMP Simple Network Management Protocol surge protective device State Of Charge State Of Health Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.
Page 324 FusionModule500 Smart Mini Data Center User Manual (02116410, 02116411, 021164112) B Acronyms and Abbreviations uninterruptible power system Issue 04 (2023-10-31) Copyright © Huawei Digital Power Technologies Co., Ltd.

Huawei FusionModule500 User Manual

Quick Links

Troubleshooting

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Huawei FusionModule500

Summary of Contents for Huawei FusionModule500