Related Manuals for activeshop YOSHIDA PRO-SPRAY LCD
Summary of Contents for activeshop YOSHIDA PRO-SPRAY LCD
- Page 1 Instructions for use YOSHIDA PRO-SPRAY LCD MILLING MACHINE Importer: ACTIVESHOP Ltd. 8b Graniczna St., building DC2A 54-610 Wroclaw, Poland www.activeshop.com.pl Rev. A/05/2024...
-
Page 2: Power Cable
The modern YOSHIDA milling machine will be perfect for beauty salon or podiatry practice. A striking metal casing and useful plastic components perfectly compose the look of this one-of-a-kind milling machine. A sturdy handle at the top of the case will allow for easy portability. The head of the device is from the well-known Marathon brand. - Page 3 Handle Cutters Head Power socket Water container Adjustment knob spray Display Foot switch socket Water supply Head socket socket Spray Cutter Ring Head Preparation before use Rotate the ring half a turn as indicated by the arrow in the figure. Insert the cutter all the way in.
- Page 4 Remove the container, as indicated by the arrow in Figure 1, unscrew the lid of the container and pour in the appropriate amount of water, not exceeding the "max" position. Then tighten the lid. Make sure the lid is tightened properly. Failure to tighten the lid may cause damage to the milling machine. Then insert the container into the milling machine base.
- Page 5 Enable Start/Pause Touch panel display Display settings: Speed adjustment is possible in standby mode or during use. The adjustment works on a range between 10, and 40. To set the desired speed, press " " or " ". Button for setting and saving individual user settings: click and enter the parameter settings.
- Page 6 User Manual: Select saved user settings: Press , to enter the work program selection, it will show M1-M6. Press once , the color will change to orange , indicating that a saved program has been selected. Then click the return button in the right corner, the display will show the saved working parameters.
- Page 7 Action Instructions: Take a milling machine head. Configure settings, direction, check if you can spray or choose the right program. Press the spray button, set the water spray power with the spray adjustment knob. Start the milling machine through the START/PAUSE button, on the display by pressing " "...
- Page 8 Enter a new password, you will be prompted to confirm the password. If an incorrect password is entered twice, enter the new password again. The password must consist of 4 digits. Working time check: You can check the total running time of the device by holding down the START/PAUSE button for 3 seconds. The settings panel will appear, click on the button will display displays total...
- Page 9 Select language Turn on the power, the operation screen will appear, then press the pause button for 3 seconds. The display will show the setting panel as follows When you click , the settings panel will appear. Select the desired language. Turn on the base of the milling machine.
- Page 10 Avoid accidentally starting the cutter head without the cutter installed. Do not touch the device when it starts working. Keep away from water and fire. Do not use the device in soggy rooms. Use safety glasses. Turn off the power when you're done working to ensure safety Solving common problems: No.
-
Page 11: Security Measures
4. Immediately remove the plug from the outlet and contact the authorized service provided by ACTIVESHOP Ltd. in the following cases: a) liquid has entered the device, b) the device emits a strange odor, smoke or makes strange sounds, (c) the power cord was damaged, (d) the device was knocked over or its housing was damaged. -
Page 12: Disposal Of The Device
At the end of their useful life, old appliances also contain full-value recyclable components, so hand them over for recycling. They should be handed over to the appropriate collection points, and can also be handed over to ACTIVESHOP Ltd. STORAGE AND TRANSPORT The device should be transported at a temperature range of (-) 20 °C to (+) 50 °C only in its original...
Need help?
Do you have a question about the YOSHIDA PRO-SPRAY LCD and is the answer not in the manual?
Questions and answers