Summary of Contents for STIEBEL ELTRON CK 150-1 Trend
Page 1
OPERACIÓN E INSTALACIÓN UTILISATION ET INSTALLATION Electric fan heater | Calentador eléctrico con ventilador | Convecteurs électriques soufflants » CK 150-1 Trend » CK 200-2 Trend Certified to ANSI/UL Std. 2021 Conforms to CAN/CSA Std. C22.2 No.46 Certificación con ANSI/UL Std. 2021 Conforme a CAN/CSA Std.
Minimum clearances to hard surfaces ���������������������� 8 14.3 Data table ��������������������������������������������������������� 9 1.2.1 Structure of safety instructions 14.4 Wiring diagram CK 150-1 Trend������������������������������� 9 14.5 Wiring diagram CK 200-2 Trend ������������������������������ 9 KEYWORD: Type of risk Warranty ���������������������������������������������������� 10 Here, possible consequences are listed that may result from failure to observe the safety instructions.
OpEraTiON Safety Other symbols in this documentation WARNING: Burns Never operate this heater ... NOTE: - if the minimum clearances to adjacent Notes are bordered by horizontal lines above and below object surfaces are not maintained, for ex- the text. General information is identified by the adjacent ample to furniture, net curtains, curtains, symbol.
2 Air discharge 3 On/off rocker switch If you have any questions concerning the registration process or warranty options, please contact Stiebel Eltron USA direct- Settings ly at (800)-582-8423. On the left side of the unit, there is an on/off rocker switch that controls the operation.
- Mount the heater no nearer than 4˝ (10 cm) from a wall Fuse has blown. Heater cannot be restarted. Contact Stiebel Eltron. socket. - Never install the heater directly below a wall socket. - When installing the heating heater in rooms with a bath or If you cannot remedy the fault, notify your qualified contractor.
iNSTallaTiON installation 11. Installation 11.2 Heater installation DANGER: Electrocution If installing the heater in rooms with a bath and/or shower, take the relevant safety zone into account in accordance with the information on the heater type plate. Install the heater in such a way that switching and control equipment cannot be touched by a person in the bath or shower.
11.4 Wiring block damaged) by a qualified contractor, using an original Stiebel Eltron spare part. The wiring block is located around the side of the unit from the cable entry point. Route the power cable to the wiring block and secure the wire using the screws.
The images above show minimum allowed clearances be- tween the installed heater and any hard surfaces. f We recommend installing the heater 6-8˝ (15-20 cm) off the floor. CK 150-1 Trend / CK 200-2 Trend CAUTION: Injury Air intake Maintain the minimum clearances.
Specification 14.4 Wiring diagram CK 150-1 Trend NOTE: The dust filter is 10 ˝ (27.5 cm) wide. To enable removal of the dust filter as described (See 6, “Cleaning, care and maintenance”, pg. 4), main- tain a sufficiently large clearance at the side.
This Warranty is valid for U.S.A. & Canada only. Warranties goods supplied which have not been installed and ope- info stiebel-eltron-usa.com may vary by country. Please consult your local Stiebel Eltron rated in accordance with the manufacturer‘s instructions. 17 West Street Representative for the Warranty for your country.
Page 11
Pásele 14.3 Tabla de especificaciones ������������������������������������� 18 las instrucciones a cualquier nuevo usuario. 14.4 Plano eléctrico CK 150-1 Trend ������������������������������� 18 14.5 Plano eléctrico CK 200-2 Trend ������������������������������� 18 Indicaciones de seguridad Garantía ����������������������������������������������������� 19 1.2.1 Estructura de las instrucciones de seguridad...
OpEraCiÓN Seguridad 1.2.2 Símbolos, tipo de peligro PELIGRO: Electrocución Antes de la limpieza, asegúrese de que la corriente Símbolo Tipo de peligro esté desconectada en el panel del interruptor y de que Lesión el elemento de calentamiento del calentador esté frío. Electrocución PELIGRO: Incendio No ponga en funcionamiento el aparato ...
La temperatura ambiental requerida puede ajustarse de forma gistro o con las opciones de garantía, por favor, póngase en continua mediante el selector de temperatura. contacto directamente con Stiebel Eltron USA en el número de Para apagar el aparato, desconecta el interruptor de circuito del teléfono (800)-582-8423.
Comuní- aparato. quese con Stiebel Eltron. - Observe la placa de especificaciones. La tensión indicada debe coincidir con la tensión eléctrica disponible. Si no puede solucionar la causa, llame al instalador. Para poder ayudarle mejor y con mayor agilidad, indique el número de la...
iNSTalaCiÓN instalación 10.1 Envío estándar INDICACIÓN: Las ranuras horizontales y verticales posibilitan un Con el dispositivo se entregan los siguientes accesorios: ajuste en caso de que los agujeros de fijación no estén - Soporte para montaje en pared precisamente donde deben estar. 11.
Las piezas de repuestos solo puede reemplazarlas (por ejemplo, si se dañan) un contratista cualificado, utili- zando una pieza de repuesto original de Stiebel Eltron. 1 Entrada de cable, vista trasera de la unidad f Conecta el cable de fuente de energía permanente al bloque de terminales.
Recomendamos que se instale el aparato a 15-20 cm (6-8˝) del suelo. PELIGRO: Lesión CK 150-1 Trend / CK 200-2 Trend Mantén los márgenes mínimos. Entrada de aire Salida de aire Entrada del cable de corriente www.stiebel-eltron-usa.com...
Especificaciones técnicas 14.4 Plano eléctrico CK 150-1 Trend INDICACIÓN: El filtro de polvo es de 275 mm (10 ˝) de grosor. Para posibilitar la remoción del filtro de polvo como se describe (Ver 6, "Limpieza, conservación y manteni- miento" pág. 13), mantén un margen lo suficiente- mente grande en el lado.
Las garantías pueden variar de un país a otro. Consulte a su embalaje en concordancia con la normativa nacional para el 413.247.3369 Las garantías pueden variar de un país a otro. Consulte a su representante de Stiebel Eltron local para conocer la Garantía tratamiento de residuos. info stiebel-eltron-usa.com representante de Stiebel Eltron local para conocer la Garantía...
Page 20
14.3 Tableau de données ��������������������������������������������� 9 pareil puis mettez-les de côté pour référence ulté- 14.4 Schéma de câblage CK 150-1 Trend �������������������������� 9 rieure. Transférez ce document à toute personne qui 14.5 Schéma de câblage CK 200-2 Trend ������������������������� 10 utilisera l’appareil.
UTiliSaTiON Sécurité 1.2.2 Symboles, nature du danger DANGER: Incendie N'utilisez pas l'appareil ... Symbole Nature du danger - lorsque les distances minimales avec les Blessure surfaces des objets voisins (mobilier, ri- deaux et voilages, autres textiles ou tout Électrocution autre matériau inflammable) ne sont pas respectées (Voir 14.2, «...
Adresse courriel: Adresse postale: Numéro de téléphone: En cas de questions à propos du processus d’inscription ou des options pour la garantie, veuillez contacter Stiebel Eltron USA directement en composant le (800)-582-8423. 1 Sélecteur de température 2 Évacuation d’air 3 Interrupteur à bascule on/off (marche/arrêt) | CK 150-1 / 200-2 Trend www.stiebel-eltron-usa.com...
UTiliSaTiON Réglages Réglages Comment remédier à un problème À gauche de l'appareil, vous trouverez un interrupteur à bascule problème Cause Solution on/off qui commande le fonctionnement de l'appareil. En position L'appareil ne chauffe Le filtre à poussière est Inspectez le filtre à pous- on (marche), l'appareil peut se mettre en marche si le réglage du pas comme prévu.
iNSTallaTiON Sécurité iNSTallaTiON 10.1 Livraison normale Les articles suivants sont livrés avec l’appareil: - Applique murale équerre de fixation Sécurité 11. Installation La maintenance et les réparations de cet équipement ne doivent DANGER: Électrocution être effectuées que par un technicien du service clientèle. Lors de l'installation de cet appareil dans des locaux avec baignoire et/ou douche, tenez compte de la zone Consignes de sécurité...
iNSTallaTiON installation 11.2 Installation de l’appareil 11.3.1 Connexion permanente DANGER: Électrocution Veillez à ce que l’appareil puisse être séparé de l’ali- mentation électrique par un disjoncteur qui décon- necte tous les pôles. ENDOMMAGEMENTS DE L'APPAREIL: Pour cet appareil, seule une connexion permanente peut être envisagée.
Expliquez les différentes fonctions de l'appareil à l'utilisateur. Attirez particulièrement son attention sur les consignes de sé- curité. Remettez les instructions d'utilisation et d'installation à l'utilisateur. CK 150-1 Trend / CK 200-2 Trend 13. Entretien Arrivée d’air Échappement d’air Admission des câbles électriques ENDOMMAGEMENTS DE L'APPAREIL: Les pièces de rechange ne peuvent être remplacées (si...
Bruit en fonctionnement 49 dB(A) 50 cm (20 po) 14.4 Schéma de câblage CK 150-1 Trend LE PLANCHER f L’image ci-dessus montre la distance minimale à respecter entre le convecteur et toute surface dure. f Les objets inflammables comme les meubles, le papier, les vêtements et les rideaux doivent demeurer à...
Sous réserve des conditions incluses dans cette garantie 4. toute absence d’entretien du Convecteur ou négligence limitée, Stiebel Eltron Inc. (le « Fabricant ») garantit par d’utiliser celui-ci selon les instructions du Fabricant; la présente le convecteur électrique (le « Convecteur ») 5.
Page 30
NOTES | CK 150-1 / 200-2 Trend www.stiebel-eltron-usa.com...
Page 31
NOTES www.stiebel-eltron-usa.com CK 150-1 / 200-2 Trend |...
Page 32
STIEBEL ELTRON, Inc. 17 West Street | West Hatfield MA 01088 Tel. 413-247-3380 | Fax 413-247-3369 info@stiebel-eltron-usa.com www.stiebel-eltron-usa.com 4 < A M H C M O = c d i f b f >...
Need help?
Do you have a question about the CK 150-1 Trend and is the answer not in the manual?
Questions and answers