Alpine PXE-X800 - AMPLIFIER Manual

Alpine PXE-X800 - AMPLIFIER Manual

Also See for PXE-X800:

Advertisement

Alpine PXE-X800 - AMPLIFIER Manual

Required Tools (Vehicle Installation Specific)

Required Tools

Accessories

Accessories

Device Information

Diagrams of Device Interfaces

Diagrams of Device Interfaces

Device Interface Functions

Device Interface Functions

Device Indicator Lights

Device Indicator Lights

1 Power amplifier AMP switch indicator light

When the power amplifier AMP output is turned off or the device is shut down, the indicator light is off;

When the power amplifier output is turned on, the indicator light is constantly on.

2 Software connection indicator light

When the PC software or tone-tuning application on mobile phone is connected, the indicator light is flashing;

When the PC software or tone-tuning application on mobile phone is not connected, the indicator light is constantly on;

When the device is shut down, the indicator light is off.

3 POWER indicator light When the device is turned on, the indicator light is constantly on; When the device is shut down, the indicator light is off.

Bluetooth Device Indicator Lights

Bluetooth Device Indicator Lights

1 POWER indicator light

When the external Bluetooth is connected to PXE-X800 normally, when the device is turned on, the indicator light is constantly on;

When the device is shut down, the indicator light is off.

2 ACCESS indicator light

When the external Bluetooth is successfully connected for communication, the indicator light is constantly on;

When it is not successfully connected, the indicator light is flashing.

Arrangement of Wire Pins

Arrangement of Wire Pins

Installation Examples

Example I: 4 channel input / 6 channel output (low level to low level)

Example I: 4 channel input / 6 channel output - Part 1

Example I: 4 channel input / 6 channel output - Part 2

Example II: 4 channel input / 6 channel output (high level to low level)

Example II: 4 channel input / 6 channel output - Part 1

Example II: 4 channel input / 6 channel output - Part 2

Example III: digital input / 6 channel output

Example III: digital input / 6 channel output - Part 1

Example III: digital input / 6 channel output - Part 2

Example IV: 4 channel input / 6 channel output (high level to high level)

Example IV: 4 channel input / 6 channel output - Part 1

Example IV: 4 channel input / 6 channel output - Part 2

Example V: 7 channel input / 10 channel output (high level to high level)

Example V: 7 channel input / 10 channel output - Part 1

Example V: 7 channel input / 10 channel output - Part 2

Device Tuning with Mobile App

Homepage

Device Tuning with Mobile App - Homepage

1 Mute Master volume set to mute.
2 Master volume Drag the fader up and down to adjust the volume.
3 Master sound source Select the master sound source (digital, high level, Bluetooth and low level).
4 Connection indication When the Bluetooth icon is red, the Bluetooth of the mobile phone is not connected; when it is green, the Bluetooth of the mobile phone is connected.
5 Menu bar The user can switch built-in power amplifier, encrypt data, set EQ gain step size and shutdown delay, share sound effects, save sound effects, play online and local sound effects and view device temperature and version number.
6 Auxiliary sound source Select the auxiliary sound source (digital, high level, Bluetooth, low level and off).
7 Pre-set sound effects Save and call pre-set sound effect settings, slide from left to right to choose from different pre-set sound effects.
8 Interface selection Five interfaces with different functions are available, Delay, Channel, Homepage, EQ and Combined Frequency and the default one is the Homepage interface.

Delay

Device Tuning with Mobile App - Delay

1 Speaker Select the corresponding speaker, drag the fader left and right in the pop-up window to adjust the delay or click "+" and "-" to adjust the delay.
2 Delay group Each channel has 6 delay groups available to choose from.
3 Delay unit The delay unit may be chosen from millisecond, centimeter and inch.

Channel

Device Tuning with Mobile App - Channel

1 Joint debugging There are joint debugging modes of "Copy channel EQ / volume from left to right" or "Copy channel EQ / volume from right to left" available.
2 Lock The current channel type can be locked.
3 Slope Select frequency division slope (-6dB/Oct, -12dB/Oct, -18dB/Oct, -24dB/Oct, -30dB/Oct, -36dB/Oct, -42dB/Oct or -48dB/Oct).
4 Output channel Slide left and right to select the output channel to set. There is a total of 12 channels to choose from.
5 Frequency divider Turn on or off high-pass / low-pass.
6 Filter type Select filter type: (Linkwitz-Riley, Butterworth and Bessel).
7 Divider frequency Select divider frequency (between 20 Hz and 20 kHz).
8 Channel type Select the output channel type in the pull-down menu.
9 Channel volume Drag the fader left and right to adjust the channel volume and the adjustment range is -60 dB ~ 6 dB; chick the speaker button to mute the channel.
10 Channel phase Select the channel phase (normal phase or reverse phase).
11 Bass phase Bass phase adjustment for output channel, adjustment range: 0°~360°.
12 Reset channel type Select "Clear" to set the current channel type as empty;
Select "Confirm" to set the current channel type as factory setting;

EQ

Device Tuning with Mobile App - EQ

1 Reset equilibrium Reset EQ setting.
2 Restore equilibrium, pass-through equilibrium Switch adjusted EQ data to pass-through state and click on it again to restore to EQ data before pass-through.
3 Output channel Slide left and right to select the output channel for EQ adjustment. There is a total of 12 channels to choose from.
4 EQ display Display the curve of EQ adjustment.
5 Frequency, Q value, gain Adjustment of frequency, Q value, and gain for output channel The gain is adjustable but the frequency and Q value are fixed in the Graphic EQ interface. The frequency, Q value and gain are all adjustable in the Parametric EQ interface.
6 Gain Drag the fader up and down to adjust the gain. The adjustment range: -12 dB ~ +12 dB.
7 Wave band on/off Switch adjusted EQ data of the current wave band to pass-through state and click it again to restore to EQ data before pass-through.
8 Parametric EQ, graphic EQ Switch between parametric EQ mode and graphic EQ mode, which will cause loss of all settings.

Combined Frequency

Device Tuning with Mobile App - Combined Frequency

1 Output channel Slide left and right to select the output channel for frequency combination. There is a total of 12 channels to choose from.
2 Active or passive input Keep the default setting as "Passive."

if changed, you will lose the sound mixer settings of this channel.
3 Input channel Drag the fader left and right or click "+" and "-" to adjust the volume of various sound sources in the channel for the purpose of sound mixing and frequency mixing.


To avoid clipping, it is strongly recommended that each channel not exceed 100.

Device Tuning with Computer Software

Device Tuning with PC (Windows) Software

Device Tuning with PC (Windows) Software - Part 1

Device Tuning with PC (Windows) Software - Part 2

Device Tuning with PC (Windows) Software - Part 3

Device Tuning with PC (Windows) Software - Part 4

Features of PC (Windows) Software

1 Temperature display Detect the temperature on the surface of the device.
2 File Load or save scene files in the computer, load or save scene files of the whole device.
3 Options Firmware update, noise threshold, built-in power amplifier, restore factory settings, shutdown delay, switch between Chinese and English, version number display.
4 Encryption Enter 6-digit encrypted password to encrypt the tuned sound effect data.
5 EQ gain step size The step size is selectable. Step size range: 0.1 dB ~ 0.5 dB ~ 1.0 dB.
6 Mute Master volume set to mute.
7 Master volume Drag the fader left and right to adjust the volume.
8 Homepage Master sound source selection (digital, high level, Bluetooth and low level), auxiliary sound source selection (digital, high level, Bluetooth, low level and off), master sound source attenuation adjustment, pre-set sound effects call or storage
9 EQ Enter the EQ interface, professional tone-tuning interface.
10 Delay Enter the Delay interface to set delay value, delay unit and delay group.
11 Combined frequency Enter the Combined Frequency interface for sound mixing and frequency mixing settings.
12 Output channel display Display the curve of the output channel.
13 EQ curve Display the current EQ curve status, set frequency, Q value and gain.
14 Frequency, Q value, gain Adjustment of frequency, Q value, and gain for output channel. The gain is adjustable but the frequency and Q value are fixed in the Graphic EQ interface. The frequency, Q value and gain are all adjustable in the Parametric EQ interface.
15 Parametric EQ, graphic EQ Switch between parametric EQ mode and graphic EQ mode, which will cause loss of all settings.
16 Low-pass filter

Turn on or off the low-pass filter to cut off high frequency.

Select filter type: (Linkwitz-Riley, Butterworth and Bessel).

Select divider frequency (between 20 Hz and 20 kHz).

Select frequency division slope (-6dB/Oct, -12dB/Oct, -18dB/Oct, -24dB/Oct, -30dB/Oct, -36dB/Oct, -42dB/Oct or -48dB/Oct).

17 High-pass filter

Turn on or off the high-pass filter to cut off low frequency.

Select filter type: (Linkwitz-Riley, Butterworth and Bessel).

Select divider frequency (between 20 Hz and 20 kHz).

Select divider frequency (-6dB/Oct-12dB/Oct-18dB/Oct-24dB/Oct-30dB/Oct, -36dB/Oct42dB/Oct or -48dB/Oct).

18 Channel phase Select the channel phase (normal phase or reverse phase).
19 Bass phase Bass phase adjustment for output channel, adjustment range: 0°~360°.
20 Channel gain Drag the fader left and right to adjust the output channel gain, that is, to adjust the volume of output. The adjustment range is -60 dB ~ +6 dB.
21 Pass-through equilibrium, restore equilibrium Switch adjusted EQ data to pass-through state and click on it again to restore to EQ data before pass-through.
22 Reset equilibrium Reset EQ setting.
23 Output channel There are 12 output channels to choose from. Configure the output channel type. Click on the speaker to mute the channel.
24 Connection indication Connect the computer and the main device with a USB cable. Open the software to connect, click on it again to disconnect.

Specification Parameters

Dynamic range ≥100dB
SNR (RCA) ≥110dB
Background noise High level: 93.3uVrms; RCA:8.8uVrms
Channel resolution ≥80dB
THD ≤0.5%
Input voltage High level: 30Vpp; RCA:6.5Vpp
Output voltage High level CH1~CH4: 40 Vpp, high level CH5~CH8: 28 Vpp; RCA: 8 Vpp
Rated power CH1~CH4:50W,CH5~CH8:25W(4Ω, 14.4V, 1kHz, 10%THD)
Maximum power CH 1 ~ CH4:100W,CH5~ CH8:50W(4Ω, 1 4.4V, 1kHz, 10%THD)
Input / output sensitivity (RCA) 1:1.23 (no power amplification)
Frequency response 20Hz~20kHz
System sampling rate 48kHz/24bit
Input impedance High level: 51Ω; RCA:20kΩ
Output impedance 51Ω
Operating voltage 9~16V
Quiescent current ≤3mA (in off state)
Stand-by power consumption ≤0.1W
REM startup input High level (H1-/H1+), ACC selectable
REM startup output 12V(0.2A)
Uptime 10s
Operating ambient temperature -20~60℃
Storage temperature -40~85℃
Net weight 2kg
Main device dimensions 228.2mm×194.5mm×45mm

Specification - Dimensions

Functional Parameters

Input signals 8 channels of high level, 4 channels of RCA audio, high resolution blue tooth, fiber/coaxial
Output signals 8 channels of high level, 12 channels of RCA audio
Output channel signal gain Range: mute, - 60dB~ + 6dB
Output signal equalizer Type: parametric EQ, graphic EQ
Frequency: 20Hz~20kHz, resolution: 1Hz
Q value (slope or gradient): 0.404 ~ 28.852
Gain: -12.0 dB ~ +12.0 dB, resolution: 0.1 dB ~ 0.5 dB ~ 1.0 dB
Output signal frequency divider Each output channel is equipped with independent multi-order high-pass filter,
Filter type: Linkwitz-Riley, Bessel or Butterworth
Filter cross-over frequency: 20 Hz ~ 20 kHz, resolution 1Hz
Filter slope (gradient): -6 dB/Oct ~ -48 dB/Oct
Output phase Normal phase or reverse phase (0°~ 360°)
Output delay 0.000~20.000ms、0~692cm、0~273inch
Pre-set sound effects Multiple sets of pre-set sound effect data can be saved in the device

Safety Instructions

Precautions


Forbid
Represents forbidden actions (must not do).

Forbid
Represents that dismounting is forbidden

Compulsory
Represents compulsory operations (must do).
warning Represents that you should pay close attention to it.

In case of problems, please stop using the device immediately.
Otherwise, it may result in personal injury or damaged product. Please return the product to the authorized Alpine dealer or nearby Alpine service center for repair.

The product is only suitable for the 12V negativegrounded vehicles.
Otherwise, it may lead to an accident like fire, etc.

Please have this device installed by professionals.
This device requires professional expertise to install the product. For safety, please contact the Alpine authorised dealer from where you bought the product to install it.

Please do not disassemble or re-fit.
Otherwise, it may result in an accident, fire or electric shock.

warning Small items like bolts or screws should be kept out of the reach from children.
If ingested, it may result in severe injury. Once ingested, please seek medical attention immediately.

warning Please do not use any function that may distract you when driving.
Any function that may cause any distraction should be used only when the vehicle is at a complete stop. To use these functions, please first stop your vehicle in a safe area. Otherwise, it may result in an accident.

warning When driving, you must maintain the volume at a level where outside noise can still be heard.
It is very dangerous to not hear an emergency vehicle alarm and road warning signal (such as railway crossing), which may result in an accident. Moreover, a volume at a maximum level may damage your hearing.

warning Cleaning of the device
Please clean the product regularly with a dry soft cloth. For any dirt that is difficult to clean, water can only be used to soak the cloth. Any other solvents may lead to dissolution.

Temperature
Before starting the device, please ensure that the temperature inside the vehicle is between +60°C and -20°C.

Repair
In case of problems, please do not repair by yourself. Please return the product to the authorized Alpine dealer or nearby Alpine service center to repair.

warning DP-Series integration
When using PXE-X800 to distribute signal to DP-653/DP-65C by active frequency division mode, please make sure that the cross-over frequency of the treble is above 1500 Hz to avoid damage to the tweeter.

warning Installation location
The device cannot be installed at the following locations:

  • Under direct sunlight and near a heat source.
  • With high humidity and near a water source.
  • Dusty sites.
  • Environments with violent vibration.

Mobile Tuning App

  • For users of iPhone, please search the mobile tuning app for PXE-X800 in APP Store, download and install it;
    www.apple.com

For users of Android phone, please scan the QR code below to download and install the app.

Mobile Tuning App (Android)

  • The wired controller (RUX-C810), sold separately may also be used to control the device.

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Alpine PXE-X800 - AMPLIFIER Manual

Advertisement

Need help?

Need help?

Do you have a question about the PXE-X800 and is the answer not in the manual?

Questions and answers

Table of Contents