Advertisement
Quick Links
Introduction
Purpose
This document provides instructions to install the FlexPay
(CRIND
Table of Contents
Topic
Introduction
Important Safety Information
Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S)
on Encore 500 S Units
Installing FlexPay EMV CRIND Retrofit Kit with Existing TRIND
Option
Abbreviations and Acronyms
Term
CCN
CRIND
EMV
ESD
E-CIM
HIP
LON
PCB
POS
PPU
SIP
TRIND
UL
®
USB
Required Tools and Materials
Following tools and materials are required for installing the FlexPay EMV CRIND Door
Upgrade Kit (EPK EMV 500 S):
• Phillips
• 1/4-inch Socket (Nut Driver)
• mm Socket Set
• Diagonal Cutters
• Double-sided Tape
• Needle Nose Pliers
• Wrench
MDE-4801C FlexPay™ EMV® CRIND® Door Upgrade Kit (EPK EMV 500 S) for Encore® 500 S Installation Instructions · May 2013
FlexPay
™
) Door Upgrade Kit (EPK EMV 500 S) on Encore
®
Description
CRIND Control Node
Card Reader IN Dispenser
Europay
MasterCard
Visa
®
®
Electrostatic Discharge
Enhanced Customer Interface Module
™
Hub Interface PCB
Local Operating Network
Printed Circuit Board
Point of Sale
Price per Unit
SPOT Interface PCA
Transmitter/Receiver IN Dispenser
®
Underwriters' Laboratory
Universal Serial Bus
Screwdriver
®
EMV
CRIND
Door Upgrade Kit (EPK EMV 500 S)
®
®
for Encore
®
®
500 S Installation Instructions
™
EMV
Card Reader IN Dispenser
®
500 S units.
®
Page
1
4
6
18
MDE-4801C
May 2013
Page 1
Advertisement
Related Manuals for GILBARCO VEEDER-ROOT FlexPay EPK EMV 500 S
Summary of Contents for GILBARCO VEEDER-ROOT FlexPay EPK EMV 500 S
- Page 1 MDE-4801C FlexPay CRIND Door Upgrade Kit (EPK EMV 500 S) ™ ® ® for Encore 500 S Installation Instructions ® May 2013 Introduction Purpose ™ This document provides instructions to install the FlexPay Card Reader IN Dispenser ® (CRIND ) Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S units.
-
Page 2: Parts List
Introduction Parts List Following table lists the parts included in the FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S): Hub Interface PCB (HIP) Assembly Quantity Item Description Part Number 2-sided 1-sided Assembly, EMV HIP M07931A002 Cable, SMART Connect M07970A001 ™... -
Page 3: Related Documents
Introduction Contactless Antenna Option Quantity Item Description Part Number 2-sided 1-sided Assembly, Contactless Antenna M08285A001 Cable, Antenna Encrypted M07703A001 Screw Sel Tp Hex Head 6-20X Q11677-26 Printer Assembly Quantity Item Description Part Number 2-sided 1-sided Assembly, Printer 6-inch Sliding M07885A001 Screw Sel Tp Hex Head 6-20X Q11677-24 Cable, USB/Ground/+24 V... -
Page 4: Important Safety Information
Important Safety Information Important Safety Information Note: Save this Important Safety Information section in a Read the Manual readily accessible location. Read, understand, and follow this manual and any other labels or related materials supplied with this equipment. If you do not understand a procedure, call a Gilbarco Authorized Service This section introduces the hazards and safety precautions Contractor or call the Gilbarco Support Center at ... - Page 5 Important Safety Information No Open Fire In an Emergency Inform Emergency Personnel Open flames from matches, lighters, welding torches, Compile the following information and inform emergency or other sources can ignite fuels and their vapors. personnel: No Sparks - No Smoking •...
- Page 6 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units To install FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S units, proceed as follows: Before you begin, read and understand all safety information in MDE-3804 Encore and Eclipse Series Start-up and Service Manual - Safety Instructions.
- Page 7 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Remove and retain components from the door (see Figure 2) that must be reused on the new door. The following hardware components can be reused: •...
- Page 8 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Remove the existing door (see Figure 3) from the dispenser. Notes: 1) After you open both doors, the top sheathing must slide over enough to remove ...
- Page 9 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Removing Existing UL Bucket and CRIND Control Node Retain the Underwriters’ Laboratory (UL) Bucket that contains the serial number information of the unit. Remove the side panels that are not required, and use double-sided tape to adhere the panel to an available spot inside the electronics cabinet.
- Page 10 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Attach the UL Bucket to T-rail [use self-tapping M00417B01 Screw (see Figure 6)]. Figure 6: Attaching UL Bucket to T-rail Disconnect the cables from the existing CRIND Control Node (CCN) and remove the CCN Assembly.
- Page 11 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Installing New Printers To install new printers on both sides of the dispenser, proceed as follows: Insert the tab at the rear of the 6-inch Printer Assembly into the U-channel in the electronics cabinet (see Figure 8).
- Page 12 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Connect the 24 V Connector Cable to the printer and Universal Serial Bus (USB) Connector (see Figure Figure 9: Connecting Printer Cables and Orientation of 24 V Connector Cable 24 V Connector Cable Connect the 24 V Connector Cable to P4 and P5 on the DIN Rail Power Supply Board ...
- Page 13 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Connect the Printer USB Cable (M06745A003) to the printer port at the rear of the FlexPay EMV CRIND (see Figure 11). Figure 11: Connecting Printer USB Cable Printer Port Printer USB Cable (M06745A003)
- Page 14 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Installing FlexPay EMV CRIND Door To install the FlexPay EMV CRIND door, proceed as follows: Place the lower hinge pin of the existing door over the lower hinge bracket. Align the new door to the upper hinge bracket and drop the upper hinge pin into the new door (see Figure...
- Page 15 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Install the HIP Assembly. Figure 14: Installing HIP Assembly Route the cables from the door and ensure that they are connected as per instructions in “Connecting Cables from FlexPay EMV CRIND Door”.
- Page 16 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Connect the Ethernet Cable (Q13850-10) from COM 5 Port on the SPOT display to the ® respective port on the HIP Assembly (A or B). Connect the M07970A001 Cable from COM 1 Port on the SPOT display unit to the base electronics on Side A of the Encore 500 dispenser (to J1111).
- Page 17 Installing FlexPay EMV CRIND Door Upgrade Kit (EPK EMV 500 S) on Encore 500 S Units Connect the CRIND two-wire cable from J404 to P404 on the HIP Assembly (see Figure 18). If you are using the G-SITE or Passport Point of Sale (POS) system, connect the two-wire ®...
- Page 18 Installing FlexPay EMV CRIND Retrofit Kit with Existing TRIND Option Installing FlexPay EMV CRIND Retrofit Kit with Existing TRIND Option To install the FlexPay EMV CRIND Retrofit Kit with existing TRIND option, proceed as follows: Locate the TRIND Adapter Board (M08472A002) mounted on the HIP Assembly. Figure 20: TRIND Adapter on HIP Assembly TRIND Adapter Board (M08472A002)
- Page 19 Installing FlexPay EMV CRIND Retrofit Kit with Existing TRIND Option Figure 21: TRIND/SPOT Interface Board (M08472A002) Connections MDE-4801C FlexPay™ EMV® CRIND® Door Upgrade Kit (EPK EMV 500 S) for Encore® 500 S Installation Instructions · May 2013 Page 19...
- Page 20 Installing FlexPay EMV CRIND Retrofit Kit with Existing TRIND Option Restore the power to the Encore 500 S unit at the breaker located in the building. Installing the FlexPay EMV CRIND Retrofit Kit with existing TRIND option is now complete. , FlexPay , and SMART Connect are trademarks of Gilbarco Inc.
Need help?
Do you have a question about the FlexPay EPK EMV 500 S and is the answer not in the manual?
Questions and answers