Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bristan Z TC 1/2 C
Summary of Contents for Bristan Z TC 1/2 C
- Page 1 Installation Instructions and User Guide Temperature Controlled Time Flow Tap Models Covered: Z TC 1/2 C Please keep this booklet for future reference. Installer, when you have read these instructions please ensure you leave them with the user.
-
Page 2: Table Of Contents
Contents Thank you for choosing Bristan, the UK’s leading taps and showers expert. We have designed this product with your enjoyment in mind. To ensure that it works to its full potential, it needs to be fitted correctly. These fitting instructions have been created to give you all of the information you need and, if you need any further help, please do not hesitate to contact us. -
Page 3: Important Safety Information
Important Safety Information • Please read these instructions thoroughly and retain for future use. • All products manufactured and supplied by Bristan are safe provided they are installed, used correctly and receive regular maintenance in accordance with these instructions. • If you are in any doubt about your ability to install this product safely you must employ the services of an experienced qualified plumber/electrically qualified person. -
Page 4: Specifications
Specifications Inlet Connections: 15mm Compression flexible connecting pipes Minimum working pressure: 1.0 bar Maximum working pressure: 5.0 bar Maximum static pressure: 10.0 bar System Requirements: Gravity fed hot & cold (Equal pressures) Gravity fed hot & cold (Differential pressure, maximum ratio 5:1) Unvented systems Instantaneous water heater (Combination boiler) Timed Flow: 15 Seconds ±... -
Page 5: Dimensions
Dimensions Dimensions are in millimeters. Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. -
Page 6: Pack Contents
Pack Contents 1. Tap Body 2. 3 l/p/m Flow Regulator (Fitted) 3. Flexible Connecting Pipes 4. Non Return Valves (Pre-fitted) 5. Filter Washers 6. Isolation Valves 7. Base Washer 8. ‘C’ Shaped Plate 9. Fixing Nut 10. Fixing Rod Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. -
Page 7: Prior To Installation
Prior to Installation Flexible Connecting Pipes Care must be taken when connecting See below for recommended ways to fit the flexible connection pipes to the the flexible connecting pipes. household pipe work to ensure they do not bend sharply and kink or twist. Slight bend 90°... -
Page 8: Installation
Installation Before installation Flush through the pipe work to ensure removal of debris. Turn off both water supplies or close any isolating valves. Tap Body 1. Fit the tap to sink Thread the fixing rod into the bottom of the tap (if not already fitted). Fit the tap to the basin / sink / work surface Washer ensuring the washer is fitted to the... -
Page 9: Operation
Operation 1. Flow Control Push and release To operate the flow of water push down fully and release the control knob. The water will flow for approximately 15 seconds ± 5 seconds. Important: If user pushes and holds down the control knob the water will not flow. 2. -
Page 10: Maintenance
Isolation Pull the non return valves open freely, valve replace with new NRV’s from Bristan if faulty. Closed / Off Replace the non return valves in the Position... - Page 11 Maintenance Cleaning the Cartridge Before carrying out any maintenance, Locking Nut turn off both water supplies and close any isolating valves. Cartridge Prise out the handle cover cap, loosen Retaining Shroud the grub screw and remove the handle. Cartridge Remove the temperature limiter and Assembly spring.
-
Page 12: Troubleshooting
Troubleshooting Symptom Cause Remedy Tap will not Isolation valves closed. Open isolation valves. operate when control knob is fully pushed in. User is holding in Release control knob. control know. The water will not flow if the control knob is held in by the user. - Page 13 Troubleshooting Symptom Cause Remedy Tap does not Isolation valves Open isolation valves fully. run for long partially closed. enough. Insufficient water Check water supply pressure. pressure. Refer to ‘Specifications’ section on page 4. Tap cartridge Remove tap cartridge assembly faulty or assembly and clean / replace.
-
Page 14: Notes
Notes 14 Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. - Page 15 Notes Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.
- Page 16 A Masco Company At Bristan, we want to make things as easy as possible for our customers. That’s why we offer solid guarantees on all our products, effective from the date of purchase, to give you peace of mind.
Need help?
Do you have a question about the Z TC 1/2 C and is the answer not in the manual?
Questions and answers