Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DFI M93053
Summary of Contents for DFI M93053
- Page 1 M93053 2.5" SBC User’s Manual © June 04, 2024 DFI Inc.
-
Page 2: Copyright
1. The changes or modifications not expressly approved by the party responsible for com- are the properties of the respective owners. pliance could void the user’s authority to operate the equipment. 2. Shielded interface cables must be used in order to comply with the emission limits. User's Manual | M93053... -
Page 3: About This Manual
It must be returned to the purchase point, factory or authorized service agency for all such work. 4. We will not be liable for any indirect, special, incidental or consequential damages to the product that has been modified or altered. User's Manual | M93053... -
Page 4: Static Electricity Precautions
Make sure the system is placed or mounted correctly and stably to prevent the chance of dropping or falling may cause damage. • The openings on the system shall not be blocked and shall be kept in distance from User's Manual | M93053... -
Page 5: Table Of Contents
Flash Images into eMMC/SD card using UUU tool ............18 WinUSB Installation ......................20 Develop Environment ......................21 General Support ........................21 Linux AP/API support ......................21 Yocto Support List ........................22 U-BOOT Function Available List ..................22 Appendix A- Mating Connectors ....................23 The Mating Connectors List ....................23 User's Manual | M93053... -
Page 6: Chapter 1 - Introduction
1 x LCD Backlight Power (Default: 5V/Opt.: 3.3V) 1 x uSD card INTERNAL I/O 1 x 8-bit DIO 1 x I2C / Touch CANBus 1 x CAN bus 2.0b Others 1 x SPI, 1 x Front Panel, 1 x UART debug User's Manual | M93053... - Page 7 Bottom Side: TBC Operating: -5 to 65°C, (-30°C ~ 80°C, TBC) Temperature Storage: -40 to 85 °C Operating: 5 to 90% RH ENVIRONMENT Humidity Storage: 5 to 90% RH MTBF STANDARDS AND CE, FCC, RoHS, UKCA Certifications CERTIFICATIONS User's Manual | M93053...
-
Page 8: Dimensions
Chapter 1 INTRODUCTION X Dimensions X Block Diagram User's Manual | M93053... -
Page 9: Chapter 2 - Hardware Installations
LAN (CN1, ETH1) Boot Mode Select LAN (CN2, ETH0) HDMI Backlight Power Select COM3 (RS-485) LVDS Download Mode Switch CAN Bus COM5 & COM4 UART Debug USB2.0 uSD Card Bottom View I2C Touch Digital I/O LCD BackLight Power User's Manual | M93053... -
Page 10: Jumper Settings
Backlight Power Select (BLJP1) „ 1-2 On: Serial Download „ 3-4 On: EMMC BOOT (Default ) „ 5-6 On: SD BOOT „ 1-3 On: 5V (Default) „ 1-2 On: 3V3 „ 4-6 On: 5V „ 5-6 On: 12V (Default) User's Manual | M93053... -
Page 11: Pin Assignment
Chapter 2 HARDWARE INSTALLATION X Pin Assignment CAN Bus (CBCN1) LCD BackLight Power (BLJ1) Assignment Assignment DIMMING CAN1H CAN1L BLONOFF 12V/5V 12V/5V 12V/5V User's Manual | M93053... -
Page 12: Dio (Tsj1)
Chapter 2 HARDWARE INSTALLATION DIO (TSJ1) SPI (SPJP1) Assignment DIO0 DIO1 DIO2 Assignment Assignment DIO3 SPI_SCLK DIO4 SPI_MOSI SPI_SS0 DIO5 *MOSI is actually SOUT SPI_MISO DIO6 *MISO is actually SIN DIO7 User's Manual | M93053... -
Page 13: I2C Touch (Tpjp1)
Chapter 2 HARDWARE INSTALLATION Front Panel (FPJP1) I2C Touch (TPJP1) Assignment Assignment Assignment Assignment ONOFF GPIO ALERT SYS_nRST SYS_ON# User's Manual | M93053... -
Page 14: Usb2.0 (Ubj2)
Chapter 2 HARDWARE INSTALLATION USB2.0 (UBJ2) COM5 & COM4 (TSJP1) Assignment Assignment Assignment Assignment RS232_SINN RS232_RTSN RS232_SOUTN RS232_CTSN COMB_DCDN COMB_SINN COMB_RTSN COMB_SOUTN COMB_CTSN COMB_DTRN User's Manual | M93053... -
Page 15: Com4 (Rs-232)
RS232_CTSN COM4 (RS-422) Assignment Assignment Assignment Assignment LVDS_A0- RS232_SINN RS232_RTSN LVDS_A0+ RS232_SOUTN RS232_CTSN LVDS_A1- ECSPI6_SS0 LVDS_A1+ ECSPI6_MOSI LVDS_A2- ECSPI6_SCLK LVDS_A2+ EP_Reset# COM4 (RS-485) LVDS_A3- ECSPI6_MISO LVDS_A3+ Assignment Assignment RS232_SINN RS232_RTSN LVDS_A_CLK- LVDS_A_CLK+ RS232_SOUTN RS232_CTSN DATA- DATA+ User's Manual | M93053... -
Page 16: Expansion Slots
3. Locate the M.2 socket on the system board 4. Make sure the notch on card is aligned to the key on the socket. 5. Make sure the standoff screw is removed from the standoff. M.2 Module M.2 Socket Stand-off Notch M.2 B-Key User's Manual | M93053... - Page 17 Screw tight the card onto the stand-off with a screw driver and a stand-off screw until the gap between the card and the stand-off closes up. The card should be lying parallel to the board when it’s correctly mounted. User's Manual | M93053...
-
Page 18: Chapter 3 - Software User Guide
>uuu emmc_uboot_kernel_HDMI.uuu ing method for the device. Please refer to the figure below for reference. 3.Before flashing images into M93053 device via UUU tool, user must configure BOOTCNFG to BOOT Type (eMMC/SD), also alleged Serial Download mode. To enter Serial Download Mode, please follow the steps below: •... - Page 19 Flashing tool logs in Windows: Sometimes, UUU flashing process might FAIL, because Windows are runtime installing necessary drivers. User can see the following processes be executed when flashing images into M93053 device. User must make sure necessary Windows drivers are installed, then the processes can complete For Ubuntu: automatically, or user can’t flash images via UUU tool successfully.
-
Page 20: Winusb Installation
Back Ground (must do it, or you can't flash image in Windows) b. Install updated winusb inf file (must do it, or you can't flash image in Windows) • The screen below is shown when the installation has been successfully completed. User's Manual | M93053... -
Page 21: Develop Environment
Use zadig to install winusb driver (must do it, or you can't flash image in Windows) If still fail to X Develop Environment install winusb driver, you can try the following method. Yocto4.2 kernel 6.1.36-2.1.0 image for M93053 project was built with Ubuntu20.04 docker image and follow i.MX_Yocto_Project_User's_Guide.pdf released by NXP. and click Intall WCID Driver. -
Page 22: Yocto Support List
(Builds Wayland weston graphics without Qt5 image). LTE module : Quectel EM06. Refer from imx-yocto-L6.1.36_2.1.0 i.MX_Yocto_Project_User's_Guide.pdf. COM Port (RS232/RS485/ Support Loopback test, (need DFI Linux user space utility). RS422) X U-BOOT Function Available List Support read input high/low status, set output voltage high/low status, control GPIO by Linux device node, 8 pins. -
Page 23: Appendix A- Mating Connectors
YIMTEX, BOX HEADER, 1*4P, F, 90D, 1.25mm, SMT, 501MW1*04MTR-2R 5V/1A Digital I/O TSJ1 TOKUTSU, BOX HEADER, 1*10P/1.25mm, F, NATURAL, 90D, SMT, 1W1257WOR0-10CNA 5V/1A LCD BackLight Power BLJ1 JST, BOX HEADER, 1*8P/1.0mm, F, NATURAL, 90D, SMT, SM08B-SRSS-TB(LF)(SN) 12V/0.7A User's Manual | M93053...
Need help?
Do you have a question about the M93053 and is the answer not in the manual?
Questions and answers