DELTA DORE TYMOOV Solar 5 SO Manual
Range of solar-powered wireless tubular motors
Hide thumbs
Also See for TYMOOV Solar 5 SO:
- Instructions manual (68 pages) ,
- Manual (24 pages) ,
- Manual (4 pages)
Subscribe to Our Youtube Channel
Related Manuals for DELTA DORE TYMOOV Solar 5 SO
Summary of Contents for DELTA DORE TYMOOV Solar 5 SO
- Page 1 TYMOOV Solar 5 SO / 10 SO / 15 SO / 20 SO Range of solar-powered wireless tubular motors...
- Page 2 Recommendations These instructions are intended for closure professionals or electricians who install, maintain or dismantle roller shutters. WARNING : Important safety instructions Incorrect installation can result in serious injuries. Follow all instructions and retain these installation instructions for future reference. - TYMOOV xSO motors are designed solely for the operation of rollers shutters for home use.
- Page 3 - TYMOOV xSO motors are motors with 868 MHz - X3D wireless receivers. They are only compatible with remote controls from the DELTA DORE X3D range : TYXIA 1701, TYXIA 2331 and TYXIA 1716. - Sufficiently rigid roller shutter slats should be used.
- Page 4 Recommendations - It is essential that you connect the TYMOOV Solar motor to the DELTA DORE solar panel and the DELTA DORE battery. Using another panel can cause functional faults. - TYMOOV xSO motors check the physical stops every 100 operations, so the motor automatically compensates for any apron movement.
- Page 5 France France Par la présente, DELTA DORE déclare sous sa seule responsabilité que le produit ci-dessus est en conformité avec la Par la présente, DELTA DORE déclare sous sa seule responsabilité que le produit ci-dessus est en conformité avec la législation d'harmonisation de l'Union Européenne :...
-
Page 6: Table Of Contents
Contents 1/ Technical characteristics ..............7 2/ Motor fitting ..................8 2.1 Crown and wheel assembly ..............8 2.2 Assembly in the tube ................8 2.3. Motor.head.position................. 9 2.4. Mounting.of.the.motor.onto.its.support ..........9 3/ Connection ..................10 4/ Starting up for the first time ............10 4.1. Exiting.transport.mode ................. 10 4.2. -
Page 7: 1/ Technical Characteristics
1/ Technical characteristics • Power supply : 12 Vcc TYMOOV solar motors can only be used with the DELTA DORE batteries supplied with the motors : TYMOOV 5 SO : 10S1P 1200 Ni-MH battery pack (7011725 / 5 et 7011738 / 20). -
Page 8: 2/ Motor Fitting
2/ Motor fi tti ng • Never strike the motor head or output shaft to fi t the motor into the tube. Never pierce the tube when the motor is installed. • To att ach the apron, use screws that do not enter the tube by more than 1 mm. -
Page 9: Motor.head.position
2.3 Motor head positi on The motor head should be positi oned on the bracket so that the cable outlet is at the bott om in relati on to the horizontal. 8 NO 8 NO 8 NO RJ11/RJ11 4 OK 4 OK 4 OK 2.4 Mounti ng of the motor onto its support... -
Page 10: 3/ Connection
3/ Connecti on The motor is supplied with a H05VVF power cable, This cable cannot be installed outdoors, unless it is inside a UV-resistant duct. TYMOOV 5 SO / 10 SO / 15 SO White Brown (+) / Blue (-) connectors Batt ery Motor head Photovoltaic solar panel... -
Page 11: Pairing.an.initial.remote.control.with.a.motor
4/ Starti ng up for the fi rst ti me When switched on for the fi rst ti me, the motor runs a cycle to warn that no transmitt er is paired. The motors will automati cally await pairing. You have 5 minutes aft er start up to associate the motor to the control device. 4.2 Pairing an initi al remote control with a motor 4.2.1 Case no. -
Page 12: Stop.settings
4/ Starting up for the first time 4.3 Stop settings You can use Auto mode if there are both upper and lower physical stops. The motor will automatically detect its end of travel distances. If there are no upper physical stops and/or automatic locks, you must set the end of travel manually. - Page 13 4.3.1 Storing 2 automatic stops ❶ Automatic upper stop Upper physical stop Stop on shutter slat Lower physical stop Press and release the button until the shutter locks against the upper stop. The stop position is stored automatically. The motor activates once. ❷...
- Page 14 4/ Starti ng up for the fi rst ti me 4.3.2 Store 1 manual stop + 1 automati c stop ❶ Position the shutter Progress stepwise Press the butt on to move the shutt er to the To progress stepwise, briefl y press the desired positi on, then press to stop it (*).
- Page 15 4.3.3 Store 2 manual stops ❶ Position the shutter Progress stepwise Press the butt on to move the shutt er to the To progress stepwise, briefl y press the required positi on, then press to stop it (*). butt ons at the same ti me, then release.
-
Page 16: 5/ Modifying Stops
5/ Modifying stops The stops must fi rst be removed then recorded again for them to be modifi ed. Remove them by proceeding as follows : > 3s Press briefl y on butt on B located On the transmitt er, press together The motor briefl y on the front panel of the remote and hold down the and... -
Page 17: 7/ Linking A Smoke Detector Directly To The Motor
7/ Linking a smoke detector directly to the motor You want to control the opening of roller shutters if smoke is detected. > 3s On the already paired transmitter, press the button for more than 3 seconds, until the motor activates briefly. Press for 3 seconds the detector button. -
Page 18: 8/ Obstacle Detection
8/ Obstacle detecti on The motors of the TYMOOV range include the obstacle detecti on feature. This fully protects the roller shutt er mechanism. Aft er locking on an obstacle, the motor reverses directi on by about 15 cm. Obstacles can only be detected when the stops have been recorded. 8.1 Setti ng the type of obstacle detecti on You can choose between two detecti on modes : - Protect+ detecti on : (default mode), more effi cient obstacle detecti on, preventi ng... -
Page 19: 9/ Erasing One Or More Pairings
9/ Erasing one or more pairings 9.1 Erasing the pairing of the remote control with the motor - Remove the front panel of the remote control. - Press butt on A (or butt on T1 for the TYXIA 2331 wall-mounted remote control). The red LED fl ashes. - Press as many ti mes as required to select the motor to remove. -
Page 20: 11/ Pairing With An Alarm Control Unit
11/ Pairing with an alarm control unit The pairing of the motor with an alarm control unit enables : - the anti -intrusion functi on att empt to raise the shutt er), - the surveillance stop/start report. 11.1 Pairing the wireless motor For intruder detecti on to work, the lower stop must be recorded automati cally with locks. -
Page 21: Defining.the.motor's.operating.mode
11.2 Defi ning the motor’s operati ng mode Alarm Stopping acti vati on of the alarm The shutt er remains in Mode 1 (default) The shutt er closes positi on The shutt er opens Mode 2 The shutt er closes The shutt er remains in The shutt er remains in Mode 3... -
Page 22: 12/ Your Remote Control Is Lost Or Not Functioning
12/ Your remote control is lost or not functi oning These procedures are used to set the motor to Awaiti ng pairing mode for a new control unit (Tyxia 1701, 2331, TYDOM etc.) when the remote control of the relevant motor has been lost or is out of order. On the new remote control : - Press twice on butt on B located on the front panel of the remote control (or butt on T2 for the TYXIA 2331 wall-mounted remote control), , so that the LED... -
Page 23: 14/ Troubleshooting
14/ Troubleshooting • The motor does not work : - Check that the wiring corresponds to the diagrams in the "Connection" chapter. - Check that the motor is not in thermal protection mode; just wait a few minutes for it to cool down. - Check whether there is a problem linked to the end of travel settings and perform the reset again.. - Page 24 www.deltadore.com...
Need help?
Do you have a question about the TYMOOV Solar 5 SO and is the answer not in the manual?
Questions and answers