Page 2
WWW.GOPOWERBIKE.COM DO NOT RETURN TO STORE! If you need any help with your new GoExpress 2.0 or GoCruiser 2.0 ebike, whether it is missing parts or you need help with assembly, please email us at Help@gopowerbike.com. We will be sure to respond!
Page 3
Welcome Thank you for purchasing the GoGoExpress 2.0/GoCruiser 2.0 from GoPowerBike. We take pride in bringing you a quality product that will offer years of enjoyment. Please read and understand this manual fully before assembling and riding your bike. If you have any questions after reading this manual, please reference the GoPowerBike Help Center or contact us by email.
Table of Contents Using This Manual General Info Safety Check and Other Information Getting Started Adjust the Handlebar Height Unfolding/Folding the Stem Unfolding/Folding the Frame Unfolding/Folding the Pedals Adjusting the Seat Post Charging Your Ebike Installing the Battery Get To Know Your Ebike Battery and Charging Riding Your Ebike Maintenance...
Assembly and first adjustment of your bike from GoPowerbike requires special tools and skills and it is recommended that this should be done by a certified, reputable bike mechanic if possible.
NOTICE: A critical aspect of assembling your bike by GoPowerbike is securing the front wheel and checking the tightness of the rear wheel axle nuts. All bikes by GoPowerbike use a quick release front wheel mounting mechanism and the rear wheel is bolted on. These mechanisms may become loose or unsecured during shipment or over time.
If the throttle, brake lever cutoff switches, pedal assistance, or lighting are functioning abnormally, intermittently, or not working, please discontinue using your ebike immediately and contact the GoPowerbike Product Support team for assistance. Quick Release Levers Quick release levers are located on your ebike to secure the seat post. These provide convenience to the user since they allow the seat post to be adjusted without tools.
Page 8
Loose, worn, or damaged handlebar grips should be replaced before you ride and can be purchased from GoPowerbike. The seat and seat post should be properly aligned, fitted to the user, and the seat post quick release should be properly tightened, fully closed, and secured before riding.
Page 9
Fully Assembled GoExpress 2.0 and GoCruiser 2.0...
Getting Started Starting notes: · Remove all packaging before beginning assembly. · The directions given in this manual—right, left, front/forward, and rear/back—are oriented as the rider would see them when seated on the bike. The “right side” of the bike, for example, is the side where the rider’s right hand and foot will be. ·...
Adjust the Handlebar Height Step 1: Unlatch the stem clamp Step 2: Before unfolding the stem, insert the telescoping stem to the minimum insertion point Step 3: Move the handlebars to the desired height Step 4: Retighten the stem clamp NOTICE! Always insert the telescoping stem past the...
Unfolding the Stem Step 1: Pull the handlebars to the upright position Step 2: Push the latch in firmly until it locks in position Step 3: Pull on the latch to confirm it is locked and the handlebars cannot fold. Folding the stem Step 1: Pull up on the silver button labeled “OPEN”...
Unfolding the Frame Step 1: Stand near the frame close to the battery. Grab the stem and rear end of the bike, lift the bike slightly and swing the bike to the closed position Step 2: Push the latch down firmly until it locks into position.
Unfolding the Pedals Step 1: Pull each pedal out until you hear a click when they lock into position Folding the Pedals Step 1: Grasp the pedal and push slightly toward the bike Step 2: Continue pushing as you raise the pedal to its folded position Step 3: The pedal will click in the folded position...
Adjusting the Seat Post Step 1: Loosen the seat post clamp Step 2: Raise or lower the seat post in the seat tube Step 3: Check that the seat is straight Step 4: Retighten the seat post clamp NOTICE! Always insert the seat NOTICE! Your leg should be post past the minimum insertion...
Charging Your Ebike Connect the DC jack of the charger to the charging port of your ebike and then the AC plug into the outlet. The charger light turns from red to green when charging is complete. ------ Still Charging ------ Fully Charged Charging Indicator Light NOTICE - Important charging notes:...
Installing the battery Locked-locking pin Step 1: Fully insert the battery pack into the bike protruding through frame with the key removed. Locking pin will be frame retracted. Step 2: Insert the key into the battery through the hole at the bottom of the frame. Continue pushing the key into the battery while twisting the keys to the desired position.
Get to Know Your Ebike-Operation Power On/Off: Press and hold the power button on the left handle for 5 seconds to turn your bike on and off. Lights On/Off: Press and hold the “+” button for 3 seconds to turn the light on/off. Shifting: You should shift your ebike the same way you shift a normal bike using the gear shifter on the right handlebar.
Riding your ebike 1. Do not use the eBike before reading this manual carefully and knowing your eBike thoroughly. 2. Do not lend your eBike to anyone who do not know how to use it, so as to avoid harm. 3.
Need help?
Do you have a question about the GoExpress 2.0 and is the answer not in the manual?
Questions and answers