Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AS MOTOR Allmaher AS 65 4T Honda
Summary of Contents for AS MOTOR Allmaher AS 65 4T Honda
- Page 1 Operator's Manual Allmäher® AS 65 4T Honda, AS 65 2T ES, AS 65 4T B&S, AS 73 4T B&S From serial number: AS 65 4T Honda: 014617110001, AS 65 2T ES: 027117110001, AS 65 4T B&S: 021317110001, AS 73 4T B&S: 019817110001 Issued: 27.10.2017, V1.0 en-Translation of the Original Operator's Manual...
-
Page 2: Notes On The Operating Manual
dummy Intended use Notes on the operating manual The device is intended only for cutting grass or similar vegetation in well-maintained grounds Dear customer, in agriculture, forestry and preservation of the countryside that are cut at least once a year. Congratulations on your purchase. -
Page 3: Table Of Contents
Contents Setting the blade speed......22 Notes on the operating manual..... Oil pressure switch........22 Contact ............ Driving ............. Device data..........Driving............. 22 Reverse gear........... 22 Intended use..........Turning............ 23 Explanation of the symbols....Pushing............ 23 Symbols in the instructions...... 5 Differential lock........ - Page 4 Disposal........... Warranty ..........Troubleshooting ........Technical data......... Accessories..........40 Declaration of conformity......
-
Page 5: Explanation Of The Symbols
dummy Inhaltsverzeichnis Prior to any repair and mainten- Explanation of the symbols ance work, pull off the spark plug connector. Symbols in the instructions In these operating instructions, the following symbols are used to denote special dangers. Warning. These symbols denote special Clean the ventilation grid! dangers. - Page 6 Type plate The type plate on the device provides you with information on the device type and the technical data. 1 Name and address of the manufacturer 2 Device designation 3 Type designation 4 Rates power output in kW / engine speed 5 Weight 6 Year of manufacture 7 Serial number...
-
Page 7: Type Overview
Type overview In this operating manual, the following device types are described. Depending on their equipment, the corresponding descriptions of this operating manual apply. 65 4T B&S 73 4T B&S 65 4T Honda 65 2T ES Equipment 2-stroke engine 4-stroke engine Accelerator lever without choke Accelerator lever with choke... -
Page 8: Safety Instructions
Safe handling of fuel Safety instructions Fuel is toxic and highly flammable. There is a Get informed! burn and explosion hazard! Keep fuel away from ignition sources and do For your safety, read these operating instruc- not smoke during handling. tions carefully. -
Page 9: Check The Device Prior To Use
Danger area Measures in case of a fire In case of a fire, use foam, dry powder extin- guisher, or carbon dioxide (CO ). Never douse with water! Check the device prior to use Prior to use, check the blade, protection skirt, drive and fastening parts, cables and cable connections for proper working condition and firm seating by visual inspection. -
Page 10: Use Caution During Operation
Use caution during operation Prior to mowing Danger of injury during motor start Personal protective measures Do not start the engine During mowing, always wear – if fuel was spilled. safety shoes with good grip and long trousers. Do not mow with –... -
Page 11: Caution When Mowing Slopes
Only mow during daylight or with adequate arti- To avoid risk of fire, keep the following com- ficial lighting. Never mow in the event of uncer- ponents free of dirt, grass, hay, leaking oil, tain weather conditions and risk of lightning. grease, etc.: Be especially carefully when mowing on soft –... -
Page 12: When Work Is Completed
Use caution during maintenance If the device tilts or slips and repair – Never try to stop a tilting or sliding device. Severe injuries can result. Only carry out work as described in these op- – Remove leaking fluids (oil, fuel, battery acid) erating instructions. -
Page 13: Device Description As 65 4T B&S And As 73 4T B&S
Device description AS 65 4T B&S and AS 73 4T B&S 1 Steerable front wheel 2 Protection skirt 3 Protection bow 4 Interlock steerable front wheel 5 Cutting height adjustment 6 Silencer 7 Ventilation grid 8 Oil filler opening 9 Starter grip 10 Lever for lateral adjustment of handle- 11 Handlebar console 12 Height adjustment of handlebar 13 Type plate... -
Page 14: Device Description As 65 4T Honda
Device description AS 65 4T Honda 1 Steerable front wheel 2 Protection skirt 3 Protection bow 4 Interlock steerable front wheel 5 Cutting height adjustment 6 Silencer 7 Ventilation grid 8 Oil filler opening 9 Starter grip 10 Lever for lateral adjustment of handle- 11 Handlebar console 12 Height adjustment of handlebar 13 Type plate... -
Page 15: Device Description As 65 2T Es
Device description AS 65 2T ES 1 Steerable front wheel 2 Protection skirt 3 Protection bow 4 Interlock steerable front wheel 5 Cutting height adjustment 6 Silencer 7 Ventilation grid 8 (not existing) 9 Starter grip 10 Lever for lateral adjustment of handle- 11 Handlebar console 12 Height adjustment of handlebar 13 Type plate... -
Page 16: Control Elements
Blade clutch lever (A) Control elements The engine clutch lever is a guard device. Handlebar console When you release the lever, the blade comes AS 65 4T B&S to a standstill within 7 seconds. Uncouple blade (0): Release the blade clutch lever and set the acceler- ator lever to MIN. - Page 17 Engine stop switch (E) Height adjustment of handlebar (12) The height of the handlebar can be adjusted Switch the ignition on and off with the via the screw of the handlebar height adjust- engine stop switch. When you switch ment (see Assembly). off the ignition, the engine is switched Switching lever (14) off.
-
Page 18: Operating Elements Only For 2-Stroke Devices
Operating elements only for 2- Information on mowing stroke devices Prior to mowing, check your device for com- Carburetor (22) with choke and tickler pleteness, proper functioning, and cleanliness. A dirty ventilation grid causes overheating of For cold start of the engine, you need the the engine, this can damage the engine. -
Page 19: Prior To Starting
Your benefits: Prior to starting – Halve oil consumption compared to 1:50 - therefore more environmentally and cost Fuel used (4-stroke devices) friendly. As fuel, use unleaded petrol (see operating in- – Optimum protection of the engine for a long structions of the engine manufacturer). -
Page 20: Tanking Up
Tanking up Danger! Fuel is ignited by hot engine parts. Prior to filling up, switch off the en- gine and wait for at least 20 minutes until the engine has cooled down. Observe the safety instructions re- garding the fuel! Warning! The fuel tank at the engine is not connected. -
Page 21: Starting
8. Let the starter rope retract slowly. Starting 9. Release the start button. 10. For mowing, set the accelerator lever to the Danger! maximum speed. During startup, there is a risk of in- jury caused by the rotating blade. AS 65 2T ES Make sure that no one is within the danger zone of the blade. -
Page 22: Setting The Blade Speed
Setting the blade speed Driving Devices with blade speed lever Driving You will achieve a good result of cutting and mulching with a high blade speed and medium In case of a hazardous situation, switch off the driving speed. drive and declutch the blade. When the blade speed is low, the tractive Drive on: power of the blade is especially high and the... -
Page 23: Turning
Turning Switching off and parking Turn the device round only where the grass has been mowed already. Caution! Turning round on an even surface: On a slope, the device can roll 1. Switch off the drive and the differential lock. away. -
Page 24: Loading
Loading Use suitable ramps for loading that – can carry the empty weight of the device + 200 kg. – are wider than the device. – have a slip-free surface. Notice! Risk of damage due to incorrect fastening of straps. Fasten the straps only at the points Fig. 9: shown in the figure. -
Page 25: Maintenance
Maintenance Warning! Risk of injury due to unexpected movement. When inspections are carried out, the device can move un- expectedly. Make sure that no persons or ob- jects are in the danger area of the blade. Make sure that no further hazards result from an unexpected move- ment. -
Page 26: Maintenance Overview
Maintenance overview Component Action Maintenance interval Device Check for safe working condition (basic inspection). ■ ▲ Clean. ■ Customer service. ▲ Fuel Check fuel level. ■ Is the tank cap closed? ■ Tank, fuel valve, Check parts for leaks and check for good condition. ■... - Page 27 Flammable material Remove easily flammable debris buildup from the engine ■ ▲ and the device. Tyres Check tyres and, if necessary, the tyre pressure. ■ ▲ For 4-stroke devices: Engine For reliable information, see the operating manual of the ■ ▲...
-
Page 28: Cleaning The Device
Cleaning the device Chain lubrication Depending on use, clean the device thor- oughly, especially the bottom and the blade. Grass cuttings and dirt that are stuck interfere with the grass ejection and impair the cutting quality. To sufficiently cool the engine, keep the engine cover, ventilation grid and engine clean. -
Page 29: Checking The Parking Brake
Checking the parking brake All shown blade parts and their fastening ele- ments must be changed Danger! – if damage or cracks are detected. If the parking brake is incorrectly ad- – at least once a year or every 50 operating justed, the device can roll away. -
Page 30: Maintenance Specifically For 4-Stroke Device
Checking the spark plugs Maintenance specifically for 4-stroke device Danger! The ignition system generates an electromagnetic field. Maintaining the engine Wearers of pacemakers must not Danger! work on live parts. If the speed of rotation is set too Soiled spark plugs reduce the engine output. high, objects can be ejected. -
Page 31: Maintenance Specifically For 2-Stroke Device
Maintaining the air filter Maintenance specifically for 2-stroke device Danger! Cleaning agents pose a fire and explosion hazard. Maintaining the engine Never clean the air filter with flam- Danger! mable solvents. If the speed of rotation is set too Caution! high, objects can be ejected. -
Page 32: Assembly
Guide bar and handlebar Assembly Scope of delivery The device is shipped in a carton. The scope of delivery included: – The device. – This operating manual. – Manufacturer’s certificate. – Tool bag. – Operating manual engine manufacturer (for 4-stroke devices) Unpacking 1. -
Page 33: Longer Storage
Longer storage Wear parts Observe the safety instructions regarding Some parts are wear parts. They wear during the handling of fuel. use and must be replaced. The warranty does Draining fuel tank: Put a piece of a tube not cover the following parts: on the fuel valve and fill the fuel in an ad- Blades, cutting blades, cutter bars, blade bolts, equate fuel container. -
Page 34: Troubleshooting
Troubleshooting The following table contains the most frequent problems and their elimination. If more problems occur, contact the closest authorised service centre. You can find an authorised service centre on our home page www.as-motor.de. Problem Possible cause Remedy Engine does not Engine stop switch is set to Set engine stop switch to ON. - Page 35 Problem Possible cause Remedy Devices with oil pressure Bring the device to a level position. switch: No oil pressure: Slope inclination is too steep Engine starts badly Choke is closed. Open the choke. or runs irregularly Air filter is dirty. Maintain air filter (see Maintenance and cleaning).
- Page 36 Engine gets hot Ventilation grid is dirty. Clean ventilation grid. Cooling fins of the engine are Have cooling fins cleaned by author- dirty. ised service centre. 4‑stroke devices: Refill engine oil (see operator’s manual Oil level in the engine is too of the engine manufacturer).
-
Page 37: Technical Data
Technical data Type AS 65 4T B&S AS 73 4T B&S Range of application (temperature) (0 - 30 °C) For temperatures below 5 °C, observe the engine manu- facturer's information regarding the engine oil. Engine, type One cylinder four stroke engine Manufacturer Briggs & Stratton Type Series 3 Intek Cylinder capacity 344 cm Performance... - Page 38 Type AS 65 4T Honda Range of application (temperature) (0 - 30 °C) For temperatures below 5 °C, observe the engine manu- facturer's information regarding the engine oil. Engine, type One cylinder four stroke engine Manufacturer Honda Type GXV 160 Cylinder capacity 163 cm Performance 3.2 kW (4.3 PS) Engine speed 3600 min Cutting device, type Cutter bar with mulching blade...
- Page 39 Type AS 65 2T ES Range of application (temperature) (0 - 30 °C) For temperatures below 5 °C, observe the engine manu- facturer's information regarding the engine oil. Engine, type One cylinder two stroke engine with easy start Manufacturer AS-Motor Germany Type AS 165 ES (Easystart) Cylinder capacity 165 cm Performance 4.5 kW (6.1 PS)
-
Page 40: Accessories
Accessories Low-pressure tyres: G06721006 Branch lifter: G06726021 Spray paint 400 ml, colour orange: G00011050 Operating hours counter: G06927008 Clinometer: G06950027 Cage wheels: G06780016 Hand protection set: G06780309 Low pressure tyres (standard equipment for AS 73 4T B&S): G06721006... -
Page 41: Declaration Of Conformity
Declaration of conformity AS-Motor Germany GmbH & Co. KG Ellwanger Straße 15 D-74424 Bühlertann www.as-motor.de Declaration of conformity We declare that the grassland mowers Type AS 65 4T Honda AS 65 2T ES AS 65 4T B&S AS 73 4T B&S starting from serial no. 014617110001 027117110001 021317110001 019817110001 as brought into circulation by us conform to all relevant - 2006/42/EC safety and health requirements of the EC directives lis- - 2014/30/EU... - Page 44 AS-Motor Germany GmbH & Co. KG Ellwanger Straße 15 D-74424 Bühlertann www.as-motor.de THE HIGH GRASS MOWER AND 2 STROKE ENGINE MANUFACTURE AS-Motor is your premium manufacturer for lawn and high grass mowers as well as 2 stroke engines. We offer our customers professional technology for steep slopes, rough terrain, and lawn care.
Need help?
Do you have a question about the Allmaher AS 65 4T Honda and is the answer not in the manual?
Questions and answers