Advertisement
Quick Links
Standard Flat Inductive Proximity Sensors
TL-W
• Front and side facing surface
• IP67
• DC 2-wire and DC 3-wire models
Ordering Information
DC 2-wire Models
Shape
Sensing distance
5mm
*1. Models with different response frequency are available. These model numbers take the form TL-W5MD#5 (e.g., TL-
W5MD15)
DC 3-wire Models
Shape
Sensing distance
1.5mm
3mm
5mm
Shielded
5mm
*1. Models with different response frequency are available. These model numbers take the form TL-W5MD#5 (e.g., TL-W5MD15)
TL-W
Output and operating status
NO
TL-W5MD1
Output
specifications
TL-W1R5MB1
TL-W3MB1
DC 3-wire
TL-W5MB1
20mm
DC 3-wire
TL-W5F1
Model
NC
*1
*1
TL-W5MD2
Output and operating status
PNP-NO
PNP-NC
---
TL-W3MB2
TL-W5MB2
---
---
TL-W5F2
Model
NPN-NO
NPN-NC
*1
TL-W1R5MC1
*1
TL-W3MC1
TL-W3MC2
*1
TL-W5MC1
TL-W5MC2
*1
TL-W20ME1
TL-W20ME2
TL-W5E1
TL-W5E2
---
*1
D-53
Advertisement
Related Manuals for Omron TL-W
Summary of Contents for Omron TL-W
- Page 1 DC 2-wire Models Model Shape Sensing distance Output and operating status TL-W5MD1 TL-W5MD2 *1. Models with different response frequency are available. These model numbers take the form TL-W5MD#5 (e.g., TL- W5MD15) DC 3-wire Models Model Output Shape Sensing distance Output and operating status...
- Page 2 Instruction manual * The response frequencies for DC switching are average values measured under the condition that the distance between each sensing object is twice as large as the size of the sensing object and the sensing distance set is half of the maximum sensing distance.
- Page 3 Dielectric strength 1000 VAC 50/60 Hz for 1 min between energized part and case Vibration resistance 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions Destruction: 500 m/s2 for 10 Shock resistance...
- Page 4 Brass Stainless steel (SUS304) Copper Aluminum Brass Copper Copper Aluminum Side length of sensing object d (mm) Side length of sensing object d (mm) Side length of sensing object d (mm) TL-W5E#/-W5F#/-W5MD# TL-W20# Iron Iron Stainless steel (SUS304) Stainless steel (SUS304)
-
Page 5: Output Circuit Diagram
Main circuit Control output Blue Non-sensing zone Sensing zone Proximity Sensor Note: Sensing The Load can be connected to either the +V and 0-V side. object TL-W5MD2 Rated sensing distance Operation indicator (red) Control output DC 3-wire Models Operating Model... -
Page 6: Correct Use
Design Mutual Interference Effects of Surrounding Metal If two or more Sensors are mounted face to face or side by side, Provide a minimum distance between the Sensor and the sur- keep them separate at the following minimum distance. rounding metal as shown in the table below. -
Page 7: Dimensions (Unit: Mm)
R1.6 R1.6 R1.6 Indicator Indicator * Vinyl-insulated round cable with three conductors, 2.9 dia. * Vinyl-insulated round cable with three conductors, (conductor cross-sectional area: 0.15 mm²; insulation 2.9 dia. (conductor cross-sectional area: 0.14 mm diameter: 0.9 mm); Note: Mounting dimensions: 17 ± 0.2 Note: insulation diameter: 0.9 mm);... - Page 8 ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. E221-E2-03-X In the interest of product improvement, specifications are subject to change without notice. D-60 Inductive Sensors...