Omron H5CX-N Datasheet page 34

H5CX-B@-N
Characteristics
Accuracy of operating time
and setting error
(including temperature and
voltage influences)
Insulation resistance
Dielectric strength
Impulse withstand voltage
Noise immunity
Static immunity
Destruction
Vibration
resistance
Malfunction
Destruction
Shock
resistance
Malfunction
Weight
Applicable Standards
Approved safety standards
EMC
I/O Functions
Start signal
Inputs Reset
Gate
Control output (OUT2)
Forecast value
setting
Forecast output (OUT1)
Outputs
Control output 2 (OUT2)
Absolute value
setting
Control output 1 (OUT1)
Response Delay Time When Resetting (Transistor Output)
The following table shows the delay from when the reset signal is input until the output is turned OFF.
Minimum reset signal width
1 ms
20 ms
34
Power-ON start: ±0.01% ±50 ms max. (See note 1.)
Signal start: ±0.005%±0.03 ms max. (See note 1.)
Signal start for transistor output model: ±0.005%±3 ms max. (See note 1 and 2.)
If the set value is within the sensor waiting time at startup the control output of the H5CX will not turn ON until the sensor waiting
time passes.
Note: 1. The values are based on the set value.
2. The value is applied for a minimum pulse width of 1 ms.
100 MΩmin. (at 500 VDC) between current-carrying terminal and exposed non-current-carrying metal parts
2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and non-current-carrying metal parts
1,000 VAC, 50/60 Hz for 1 min between control output, power supply, and input circuit
1.0 kV (between power terminals)
1.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts)
±480 V (between power terminals) and ±600 V (between input terminals), square-wave noise by noise simulator
(pulse width: 100 ns/1 µs, 1-ns rise)
Destruction: 15 kV
Malfunction: 8 kV
10 to 55 Hz with 0.75-mm single amplitude in three directions for 2 h each
10 to 55 Hz with 0.35-mm single amplitude in three directions for 10 min each
2
300 m/s in three directions, three cycles
2
100m/s in three directions, three cycles
Approx. 105 g (Timer only)
UL508/Listing, CSA C22.2 No. 14, conforms to EN 61812-1 (pollution degree 2/overvoltage category III)
Conforms to VDE0106/P100 (finger protection).
(EMI)
Emission Enclosure:
(EMS)
Immunity ESD:
Immunity RF-interference:
Immunity Conducted Disturbance:
Immunity Burst:
Immunity Surge:
Starts timing.
• Resets present value. (The present value returns to 0.)
• Timing stops and control output turns OFF while reset input is ON.
• Reset indicator is lit while reset input is ON.
Inhibits timer operation.
Turns ON when the present value reaches the set value.
Turns ON when the present value reaches the forecast value.
Turns ON when the present value reaches set value 2.
Turns ON when the present value reaches set value 1.
(Reference value)
Output delay time
0.8 to 1.2 ms
15 to 25 ms
EN61812-1
EN55011 Group 1 class A
EN61812-1
EN61000-4-2: 6 kV contact discharge (level 2)
8 kV air discharge (level 3)
EN61000-4-3: 10 V/m (Amplitude-modulated, 80 MHz to 1 GHz) (level 3);
10 V/m (Pulse-modulated, 900 MHz 5 MHz) (level 3)
EN61000-4-6: 10 V (0.15 to 80 MHz) (level 3)
EN61000-4-4: 2 kV power-line (level 3);
1 kV I/O signal-line (level 4)
EN61000-4-5: 1 kV line to lines (power and output lines) (level 3);
2 kV line to ground (power and output lines) (level 3)