Page 1
LOT NUMBER: DATE PURCHASED: 3-in-1 TV Stand Model # XL-44 / XL-44E / XL-44W U.S. Patent 8,561,551 CA Patent 2,811,974 This item is designed to be a 3-in-1 configuration. Please choose the option that best suits your needs. DO NOT discard any of the hardware or parts that you will not use on your chosen option. This will allow you to use this TV Console in different configurations at a later date, if desired.
Page 2
G E N E R A L I N F O R M A T I O N , T I P S a n d T R I C K S 1. Please read the Assembly Instructions prior to assembling this product. 2.
Page 3
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Shelf Frame (Qty. 1) B- Middle Shelf Frame (Qty. 1) C- Bottom Shelf Frame (Qty. 1) D- Spine Assembly (Qty.
Page 4
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. (6) 2-1/2” Bolt (7) Lock Washer (8) Flat Washer (9) Flange Nut (Qty. 1+1 extra) (Qty. 15+1 extra) (Qty.
Page 5
Assembly Instructions 5/8” Bolt (2 used in this step) ③ Flat Washer Lock Washer 1” Bolt (2 used in this step) (2 used in this step) (4 used in this step) ⑧ ④ ⑦ NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled, go back and fully tighten all bolts.
Page 6
Assembly Instructions 1” Bolt (6 used in this step) ④ 1-1/4” Bolt (4 used in this step) ⑤ Flat Washer Lock Washer (4 used in this step) (4 used in this step) ⑧ ⑦ 5. Align and attach the Left Leg (E) to Top Shelf Frame (A) by threading two 1-1/4” Bolts (5) with the Washers (7 and 8) from inside the shelf frame through the drilled holes on side rail and screw into the threaded sockets on the Leg.
Page 7
Assembly Instructions for Table-top Console 9. At the back side of the Spine Assembly (D), unscrew the four bolts and four washers to remove the Upper Spine. So that you can use the table top console configuration. NOTE: Keep the Upper Spine and the fasteners at a proper place in case you will use the floating swivel mount.
Page 8
Assembly Instructions for Table-top Console Flat Washer 2-1/2” Bolt Lock Washer ⑥ (1 used in this step) (1 used in this step) (1 used in this step) ⑧ ⑦ Spine End Cap Flange Nut (1 used in this step) (1 used in this step) ⑨...
Page 9
Assembly Instructions for Table-top Console 5/8” Bolt (4 used in this step) ③ 12. Attach 2 Cable Wheels (M) to the backside of Lower Spine (D) with the 5/8” Bolts (3). Tighten the bolts with the enclosed 4 mm hex wrench. NOTE: You can use the Cable Wheels to help keep your entertainment center’s cables and cords organized.
Page 10
Assembly Instructions for Table-top Console G/H/I A/B/C Suction Cup (18 used in this step) ① 13. Put the Suction Cups (1) firmly into the top holes and the inside metal tabs on 3 Shelf Frames (A, B and C) as shown. TIP: If a suction cup resists insertion, try pressing down on the middle of the cup with the hex wrench while twisting it clockwise into the hole.
Page 11
Assembly Instructions for Table-top Console Tools required: Hex wrench (provided), Phillips screwdriver, mallet, power drill and 1/8” drill bit (not provided). 15. Position the assembled unit at the desired location against a wall. If necessary, adjust the pre-attached Floor Levelers at the bottom of both Legs (E and F) to level the unit. Now, follow the instructions printed on the plastic bag containing the Tipping Restraint Hardware to attach the tip-over restraint to the spine and the wall.
Page 12
Assembly Instructions for Floating Swivel Mount Flat Washer Lock Washer 5/8” Bolt (4 used in this step) (4 used in this step) (4 used in this step) ⑧ ⑦ ③ 17. Fasten the Swiveling Bracket (J) to the top of the Upper Spine (D) with four 5/8” Bolts (3) and four Washers (7 and 8).
Page 13
Assembly Instructions for Floating Swivel Mount 1/2” Bolt Flat Washer Lock Washer (4 used in this step) (4 used in this step) (4 used in this step) ② ⑧ ⑦ 18. Hold and attach the flat side of the Mounting Frame (K) onto the Swiveling Bracket (J) using four 1/2”...
Page 14
Mounting the Monitor Brackets to a television with a Flat Back AAA / CCC EEE / GGG LLL / MMM NNN / OOO LL / LR BBB / DDD FFF / HHH / III / JJJ LLL / MMM LL / LR NNN / OOO NOTE: For televisions with a curved or recessed back, proceed directly to next page.
Page 15
Mounting the Monitor Brackets to a television with a Curved/Recess Back LL / LR LL / LR / III / LL / LR LL / LR 21. Determine the correct diameter of the bolt the TV requires by hand threading them into the threaded insert on the back of the TV.
Page 16
Assembly Instructions for Floating Swivel Mount LL/LR LL/LR MAKE SURE ALL BOLTS ARE TIGHT AND THE SPINE IS AT A 90 DEGREE ANGLE AND VERIFY THE MOUNTING FRAME IS LEVEL, USING A QUALITY LEVEL, PRIOR TO INSTALLATION OF TV. 23. Ask for assistance to lift the television up to hang the Monitor Brackets (LL / LR) onto the Mounting Frame (K).
Page 17
Assembly Instructions for Floating Swivel Mount 25. The Monitor Brackets (LL / LR) can tilt up to 11˚ downward and 5˚ upward, depending on your optimum viewing position. Keep the enclosed 3/16” hex wrench to ensure the tilt adjustment knobs remain tightly fastened.
Page 18
Assembly Instructions for Floating Swivel Mount 5/8” Bolt (4 used in this step) ③ 26. Attach 2 Cable Wheels (M) to the backside of the Spine Assembly (D) with the 5/8” Bolts (3). Tighten the bolts with the enclosed 4 mm hex wrench. NOTE: You can use the Cable Wheels to help keep your entertainment center’s cables and cords organized.
Page 19
Assembly Instructions for Floating Swivel Mount G/H/I A/B/C Suction Cup (18 used in this step) ① 27. Put the Suction Cups (1) firmly into the top holes and the inside metal tabs on 3 Shelf Frames (A, B and C) as shown. 28.
Page 20
Assembly Instructions for Floating Swivel Mount Tools required: Hex wrench (provided), Phillips screwdriver, mallet, power drill and 1/8” drill bit (not provided). 29. Carefully move the console and position it at the desired location against a wall. If necessary, adjust the pre-attached Floor Levelers at the bottom of the Legs (E and F) to level the unit. 30.
Page 21
The following steps are only for those who wish to mount their TV directly to the wall. If you have already mounted your TV to the Swinging Floater or plan to display your TV on the top surface of the Console, disregard the following steps. Assembly Instructions for Universal Wall Mount Installing the Mounting Frame onto a WOODEN STUD WALL 2.50"...
Page 22
Assembly Instruction for installing the Mounting Frame onto BRICK, SOLID CONCRETE OR CONCRETE BLOCK WALLS 2.50" (63 mm) Maximum weight 135 lb (61.2 kg) Concrete Anchors should only be used for masonry mounting. NEVER use the wall anchors to mount the unit to drywall. NOTE: If you are mounting your TV to a wall with wooden studs, skip this section.
Page 23
Assembly Instructions 38. Attach the Monitor Brackets (LL / LR) to the back of the television following steps 19 and 20, or 21 and 22, depending on the type of TV that you own. 39. Once the Monitor Brackets (LL / LR) are attached onto the back of the television, ask for assistance to lift the television up to attach the Monitor Brackets onto the Mounting Frame (K).
Page 24
Care and Maintenance For everyday cleaning, chrome, brass, aluminum, and painted metal surfaces can be kept looking their best by wiping with a slightly damp, soft cotton cloth, or vacuum cleaner brush. If soiled, wipe with clean sponge or cloth wrung out of water. Wipe dry with cloth or paper towel to avoid water spots.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
Page 27
LOTE DE NÚMERO: FECHA DE COMPRA: Consola para Televisión 3-en-1 Modelo # XL-44 / XL-44E / XL-44W Patente en EUA 8,561,551 Patente en CA 2,811,974 Este producto esta diseñado para configuración 3 en 1. Por favor escoga cual de las 3 opciones es adecuada para usted.
Page 28
I N F O R M A C I O N G E N E R A L , R E C O M E N D A C I O N E S Y T R U C O S 1.
Page 29
Lista de Partes y Artículos de Ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamble. A- Repisa superior (Cant. 1) B- Repisa intermedia (Cant. 1) C- Repisa inferior (Cant. 1) D- Poste (Cant.
Page 30
Lista de Partes y Artículos de Ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes antes de iniciar el ensamble. (6) Tornillo de 2-1/2” (7) Arandela de presión (8) Arandela plana (9) Tuerca barril (Cant. 1+1 extra) (Cant.
Page 31
Instructivo de ensamble Tornillo de 5/8” (2 usados en este paso) ③ Arandela plana Arandela presión Tornillo de 1” 2 usados en este paso 2 usados en este paso 4 usados en este paso ⑧ ⑦ ④ NOTA: Por favor no apretar todos los tornillos hasta que termine de ensamblar todas las piezas. Una vez montado, volver atrás y apretar todos los tornillos.
Page 32
Instructivo de ensamble Tornillo de 1” 6 usados en este paso ④ Tornillo de 1-1/4” 4 usados en este paso ⑤ Arandela plana Arandela presión 4 usados en este paso 4 usados en este paso ⑧ ⑦ 5. Alinear y asegurar el pata izquierdo (E) al marco de la repisa superior (A) mediante el uso de dos tornillos de 1-1/4"...
Page 33
Instructivo de ensamble opción consola tipo mesa 9. En la parte posterior del ensamble del poste (D), desatornille los cuatro pernos y las cuatro arandelas para retirar la parte superior. Para que pueda usar la configuración de la consola de sobremesa.
Page 34
Instructivo de ensamble opción consola tipo mesa Arandela plana Tornillo de 2-1/2” Arandela presión ⑥ 1 usados en este paso 1 usados en este paso 1 usados en este paso ⑧ ⑦ Tapa plástica Tuerca barril 1 usados en este paso 1 usados en este paso ⑨...
Page 35
Instructivo de ensamble opción consola tipo mesa Tornillo de 5/8” (4 usados en este paso) ③ 12. Coloque 2 guías para cable (M) a la parte posterior del poste inferior (D) con los tornillos de 5/8" (3). Apriete los tornillos con la Llave hexagonal 4 mm. NOTA: Puede utilizar las guías de cables para ayudar a mantener los cables de su centro de entretenimiento juntos y cables organizados.
Page 36
Instructivo de ensamble opción consola tipo mesa G/H/I A/B/C Ventosa (18 usados en este paso) ① 13. Coloque las ventosas (1) firmemente en los orificios superiores y s en el interior de las esquinas de las repisas (A, B y C), como se muestra arriba. CONSEJO: Si una ventosa se resiste a la inserción, trate de presionar en el centro de la misma con la Llave hexagonal mientras gira hacia la derecha en el agujero.
Page 37
Instructivo de ensamble opción consola tipo mesa Herramientas necesarias: Llave hexagonal (incluida), destornillador de estrella, taladro eléctrico y broca de 1/8" (no incluida). 15. Coloque la consola montada en la posición deseada en la pared. Si es necesario, ajuste los niveladores de piso pre-conectados en la parte inferior de las patas (E y F) para nivelar la unidad.
Page 38
Instructivo de ensamble opción flotador giratorio Arandela plana Arandela presión Tornillo de 5/8” 4 usados en este paso usados en este paso 4 usados en este paso ⑧ ⑦ ③ 17. Fijar giratoria soporte (J) a la parte superior del poste superior (D) con cuatro tornillos de 5/8" (3) y arandelas (7 y 8).
Page 39
Instructivo de ensamble opción flotador giratorio Tornillo de 1/2” Arandela plana Arandela presión (4 usados en este paso) 4 usados en este paso 4 usados en este paso ⑧ ⑦ ② 18. Mantenga y sujete el lado plano del marco de montaje (K) en el soporte giratorio (J) por medio de cuatro tornillos de 1/2"...
Page 40
Para montar el marco en televisiones con respaldo plano AAA / CCC EEE / GGG LLL / MMM NNN / OOO LL / LR BBB / DDD FFF / HHH / III / JJJ LLL / MMM LL / LR NNN / OOO NOTA: Para Televisiones con respaldos curvos o desnivel proceda directamente a la página siguiente 19.
Page 41
Para montar el Marco en Televisiones con respaldo curvo /desnivel LL / LR LL / LR / III / LL / LR LL / LR 21. Determine el diámetro correcto de tornillos que utilizará en su televisión atornillando con sus manos para asegurar que entren bien, si encuentra resistencia detenganse inmediatamente.
Page 42
Instructivo de ensamble opción flotador giratorio LL/LR LL/LR ASEGÚRESE QUE LOS TORNILLOS ESTEN FIRMES Y ESTAN EN UN ANGULO DE 90 GRADOS Y NIVELADOS PARA VERIFICAR EL MARCO DE MONTAJE ESTA AL NIVEL PREVIO A LA INSTALACIÓN DE LA TV 23.
Page 43
Instructivo de ensamble opción flotador giratorio 25. Los soportes del monitor (LL / LR) pueden inclinarse hasta 11 ˚ hacia abajo y 5 ˚ hacia arriba, dependiendo de su posición de visualización óptima. Mantenga la llave hexagonal de 3/16" adjunta para que las perillas de ajuste de inclinación en el futuro estén bien apretadas.
Page 44
Instructivo de ensamble opción flotador giratorio Tornillo de 5/8” (4 usados en este paso) ③ 26. Coloque 2 guías para cable (M) a la parte posterior del poste inferior (D) con los tornillos de 5/8" (3). Apriete los tornillos con la Llave hexagonal 4 mm. NOTA: Puede utilizar las guías de cables para ayudar a mantener los cables de su centro de entretenimiento juntos y cables organizados.
Page 45
Instructivo de ensamble opción flotador giratorio G/H/I A/B/C Ventosa (18 usados en este paso) ① 27. Coloque las ventosas (1) firmemente en los orificios superiores y s en el interior de las esquinas de las repisas (A, B y C), como se muestra arriba. 28.
Page 46
Instructivo de ensamble opción flotador giratorio Herramientas necesarias: Llave hexagonal (incluida), destornillador de estrella, taladro eléctrico y broca de 1/8" (no incluida). 29. Cuidadosamente mueva la consola y colocarla en la posición deseada contra la pared. Si es necesario, ajuste los niveladores de piso pre-conectados en la parte inferior de las patas (E y F) para nivelar la unidad.
Page 47
Los pasos siguientes son solo para en caso de querer montar su TV en la pared. Si ya monto su TV en el Marco Giratorio o planea poner su TV directamente sobre la consola, no tomar en cuenta los pasos siguientes. Instructivo de Ensamble para Marco de Montaje Universal Instalando el Marco a una pared de Madera 2.50"...
Page 48
Instructivo de Ensamble de Marco de Montaje para Ladrillo, Concreto o Bloque de Concreto 2.50" (63 mm) Máxima carga 135 lb (61,2 kg) Taquetes para concreto deben ser utilizadas unicamente para concreto NUNCA en tabla roca. NOTA: Si esta montando esta TV a una pared con barrotes de madera, no continue en esta sección.
Page 49
Instructivo de ensamble 38. Fije los soportes de monitor (LL/LR) a la parte trasera del televisor siguiendo los pasos 19 y 20, o 21 y 22, dependiendo del tipo de TV que usted posee. 39. Una vez que los soportes de monitor (LL/LR) se unen a la parte trasera del televisor, pida ayuda para levantar la televisión hasta adjuntar los soportes de monitor en el marco de montaje (K).
Mantenimiento y cuidados Para una limpieza diaria, las superficies de cromo, bronce, aluminio y de metal pintado se mantienen mejor limpiándolas con un trapo de algodón suave, levemente humedecido, un sacudidor o con el cepillo de la aspiradora. Si hay manchas límpielas con una esponja o un trapo limpio húmedo (exprimido). Seque completamente con un trapo a una toalla de papel para evitar manchas de agua.
Page 51
GARANTÍA DE CALIDAD (Garantía valida solo en Estados Unidos) Nosotros estamos seguros que Usted se encontrará feliz con la compra de esté producto de Whalen Furniture. Si este producto tiene alg ú n defecto de ensamblado o material o si tiene alguna falla en uso normal, nosotros lo repararemos o lo remplazaremos hasta por un (1) año a partir de la fecha de compra.
Need help?
Do you have a question about the XL-44W and is the answer not in the manual?
Questions and answers