IMPORTANT SAFETY INSTRUCTIONS U.K. MAINS PLUG WARNING A molded mains plug that has been cut off from the cord is unsafe. Discard the mains plug at a suitable disposal facility. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP The symbols shown above are internationally accepted symbols that warn of potential POWER SOCKET.
IMPORTANT SAFETY INSTRUCTIONS WARNING FOR YOUR PROTECTION READ THE FOLLOWING: READ THESE INSTRUCTIONS. KEEP THESE INSTRUCTIONS. HEED ALL WARNINGS. FOLLOW ALL INSTRUCTIONS. DO NOT USE THIS APPARATUS NEAR WATER. CLEAN ONLY WITH A DRY CLOTH. FOR INDOOR USE ONLY. DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS. DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.
CONSIGNES DE SE CURITE IMPORTANTES AVERTISSEMENT CONCERNANT LA FICHE SECTEUR Une fiche secteur moule e qui a e te coupe e du cordon est dangereuse. Jeter la fiche secteur dans un centre de de chets adapte . VOUS NE DEVEZ EN AUCUNE CIRCONSTANCE INSE ...
Page 5
CONSIGNES DE SE CURITE IMPORTANTES AVERTISSEMENT POUR VOTRE SE CURITE LIRE ATTENTIVEMENT : LIRE CES CONSIGNES. CONSERVER CES CONSIGNES. RESPECTER TOUS LES AVERTISSEMENTS. SUIVRE TOUTES LES CONSIGNES. NE PAS UTILISER CET APPAREIL PRE S DE L’EAU. NETTOYER UNIQUEMENT AVEC UN CHIFFON SEC.
London Wall EC2M 5QQ EC2M 5QQ +44 207 562 9450 +44 207 562 9450 Harman Professional Inc. Harman Professional Inc. 10653 S. River Front Parkway, Suite 300 10653 S. River Front Parkway, Suite 300 South Jordan, Utah 84095, E TATS-UNIS South Jordan, Utah 84095, USA Te ...
Ethernet Cable Recommendations When installing Ethernet Contrio controllers, Cat 5, Cat 5e or Cat 6 cabling should be used. Extra care must be taken when using shielded Ethernet cables to ensure the shield does not short to the controller's printed circuit board. Note that bulky molded Ethernet cables may be obstructed by the printed circuit board.
Page 9
1. Locate Button This small pinhole provides access to the Locate button. Pressing the Locate button allows an online controller to be easily identied within Audio Architect , see or urther ™ 'Locate' on page 15 inormation on unctions perormed with this button. 2.
Mechanical Installation The US versions o the Contrio wall controllers were designed to t into standard 1-gang or 2-gang US wall boxes. The EU versions were designed to t into standard EU 1-gang or 2-gang square and round boxes. Screws are provided with each controller to x them in place.
Page 12
Connections Both power and network connectivity are supplied to the Ethernet Contrio controllers via their RJ-45 Ethernet ports. Power must be supplied to the controllers via an IEEE802.3a compliant Power over Ethernet (PoE) device. Note that PoE+ (IEEE802.3at compliant) devices can also be used with the Contrio controllers as they are backwards compatible with the IEEE802.3a...
Page 13
Connection Diagrams Using A Midspan Soundweb London Device (e.g., BLU-806) PoE Midspan Power Adapter Ethernet Contrio Controller Using An Endspan Soundweb London Device (e.g., BLU-806) PoE Endspan (Switch) Power Cord Ethernet Contrio Controller...
Ground Lug Connection (Optional) A ground lug is provided on all Contrio controllers or connecting to an earth ground. This can provide urther protection against ESD (Electrostatic Discharge). In most cases this connection should not be necessary. However, i you experience irregular behavior when testing a Contrio controller, connecting this lug to an earth ground may resolve the issue.
Page 15
Locate Each Ethernet Contrio controller has a pinhole Locate pushbutton on the aceplate that will trigger the locate unction. Pressing the Locate button using a small, long object, such as a paperclip, will cause a controller's ront panel LEDs to fash. I the controller is programmed and online with Audio Architect, the corresponding controller icon will also fash in the Audio Architect design le to...
Page 16
Factory Reset & Restart Factory Reset The Factory Reset will revert an Ethernet Contrio controller back to its uncongured, actory-deault state by deleting its conguration and clearing any set IP address inormation. To Factory Reset a controller: 1. Power o the controller. 2.
Other Functions The ollowing unctions are congured using the Contrio Deault Control Panel rom within Audio Architect. Sleep Function When enabled, the Sleep unction allows the Contrio controller's LEDs and displays to 'sleep' (turn o) ater a specied period o operator inactivity, which can be entered in the 'Sleep Delay' eld.
Page 18
Lockout Active Function (Excludes EC-V Model) The 'Lockout Active' button on the Contrio Deault Control Panel provides a mechanism to disable a Contrio controller until a security PIN is entered. This might be appropriate when the controller is located in a public area and restricted access to the controller unctions is required.
6. Go online and load the design to the Contrio controller. 7. The controller will now be unlocked. LED Maximum Brightness There are 4 selectable brightness levels or a Contrio controller, they are: LED Maximum Brightness 1 (dim) to 4 (bright). These values can be changed in the controller's Deault Control Panel, which is accessed by right-clicking on the controller rom the main view in Audio Architect and selecting the 'Deault Control Panel' option.
Need help?
Do you have a question about the BSS soundweb CONTRIO EC-V and is the answer not in the manual?
Questions and answers