Summary of Contents for Assa Abloy Corbin Russwin ML20700 Series
Page 1
ASSA ABLOY Installation Instructions For ML20700 TCPAC1 Series In U.S.: In Canada: Mortise Lockset Corbin Russwin, Inc. ASSA ABLOY Door Security Solutions Canada 225 Episcopal Road 160 Four Valley Drive Berlin, CT 06037 USA Vaughan, Ontario, Canada L4K4T9 FM304 10/18 www.corbinrusswin.com www.assaabloy.ca...
® ML20700 Series Mortise Lock ASSA ABLOY Table of Contents Page 1) Warning………………………………………………………………. 2) General Description…………………………………………………. 3) Specifications/Features…………………………….…………….… 4) Product Illustration……………..……………………………………. 5) Installation Instructions……………………………………………… 5-16 1) Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
® ML20700 Series Mortise Lock ASSA ABLOY 2) General Description Designed specifically for the campus market, the Corbin Russwin Access 700 TCPAC1 Series mortise lock provides offline card/PIN access control with both keypad and magstripe card technology (or magstripe only).
® ML20700 Series Mortise Lock ASSA ABLOY 5) Installation Instructions Verify Hand and Bevel of door. Illustrations shown are as viewed from the outside or secure side of opening. Left Hand Left Hand Right Hand Right Hand Hinges Left. Reverse Bevel Hinges Right.
Page 6
® ML20700 Series Mortise Lock ASSA ABLOY 5) Installation Instructions Handing of Lock Body Step 1) Move the red locking screw to Catch Plate side of lock body being locked (Fig. 1) Step 2) Push in latch then depress catch plate with screw driver (Fig.
Page 7
® ML20700 Series Mortise Lock ASSA ABLOY 5) Installation Instructions Install Lock Body into Door Feed wires through hole as shown. Insert two #12 combination screws. IMPORTANT: Door must remain open during installation. Use door stop INSTALL TWO #12 SCREWS...
Page 9
® ML20700 Series Mortise Lock Standard Lever x Lever Trim Installation ASSA ABLOY 5) Installation Instructions Use Correct Spindle Orientation INSIDE STANDARD GOOD Lever Lever Align adjustment bolt with threaded hole in lever. Adjustment bolt needs Adjustment bolt needs Adjustment bolt fully aligned.
Page 10
® ML20700 Series Mortise Lock ® MUSÉO Lever x Lever Trim Installation ASSA ABLOY 5) Installation Instructions Thread adapter plate hub into Align adapter plate hub with square lever and fully tighten hole in lever; keeping hub as tight as possible...
Page 12
® ML20700 Series Mortise Lock Cylinder & Scalp Installation ASSA ABLOY 5) Installation Instructions ® L O Y ® L O Y 7/64 Allen Wrench ® L O Y ® AS SA AB LO Y NOTE: Key and cylinder must be rotated as shown ®...
Page 14
® ML20700 Series Mortise Lock ASSA ABLOY 5) Installation Instructions Install Outside Escutcheon a nd Inside Mounting Plate Feed wires as shown. Install four #8-32 machine screws and two #8 surface screws (required for fire rated doors). For exterior applications peel adhesive backing off gasket and stick to escutcheon prior to installation.
Page 15
® ML20700 Series Mortise Lock ASSA ABLOY 5) Installation Instructions Install Electronics Hous ing onto Mounting Plate Snap in electronics, then make connections shown below. From Outside Trim (ground) From Outside Trim (card Reader) From Outside ® Trim (keypad) Electrical...
Page 16
® ML20700 Series Mortise Lock ASSA ABLOY 5) Installation Instructions Install Inside Escutcheon Make sure DIP Switch (FIG 1) is set correctly before installing escutcheon. Install escutcheon using two #8-32 T20 Security Torx Screws. (Be careful not to pinch wires under escutcheon.)
Need help?
Do you have a question about the Corbin Russwin ML20700 Series and is the answer not in the manual?
Questions and answers