Advertisement

Quick Links

WEEE DISASSEMBLY INSTRUCTIONS
SUPERMICRO AS -2115HS-TNR ENCLOSURE
Abstract
This document provides clear guidance for end-of-life recyclers on how to identify
and disassemble reportable materials in compliance with the Waste Electrical and
Electronic Equipment (WEEE) directive.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AS -2115HS-TNR and is the answer not in the manual?

Questions and answers

Summary of Contents for Supermicro AS -2115HS-TNR

  • Page 1 WEEE DISASSEMBLY INSTRUCTIONS SUPERMICRO AS -2115HS-TNR ENCLOSURE Abstract This document provides clear guidance for end-of-life recyclers on how to identify and disassemble reportable materials in compliance with the Waste Electrical and Electronic Equipment (WEEE) directive.
  • Page 2: Table Of Contents

    Table of Contents Reportable Materials on AS -2115HS-TNR ....................5 Disassemble Instructions .......................... 5 Step-by-Step Disassembly Instructions ..................8 Removing Cable and Chassis Top Cover ..................8 Removing Hard Disk Drive (HDD) / Solid State Drive (SDD) ............9 Removing Power Supply ......................10 Removing Advanced I/O (AIOM) Network Card ................
  • Page 3 Product Views Front view Rear view Product construct view Hard Disk Drive/ Solid State Drive Backplane Fans...
  • Page 4 Power Supply Riser Card AIOM Card Riser Bracket AIOM Cable Add-On Module Motherboard Processor DIMM...
  • Page 5: Reportable Materials On As -2115Hs-Tnr

    1. Reportable Materials on AS -2115HS-TNR According to Article 8(2) and Annex VII of WEEE directive 2012/19/EU, Below materials and components should be selectively treated. Description Notes Quantity With a surface greater than 10 sq cm 2.3,3.5, 4.1, 5.1, 6.1, 8.1,...
  • Page 6 The intent of this document is to provide guidance to recyclers on the presence of materials and components at the product / family level, as required by the EU WEEE Directive 2012/10/EU. This document should also help direct recyclers to proper methods for removing parts and general product disassembly instructions.
  • Page 7 Backplane Fans Screws Motherboard, Riser Cards, Backplane, Add- On Module, AIOM Cable Battery Cables Power Supply Air Shroud Power Supply Power Enclosure*2 Screws and Standoff*2 Set Power Supply Module*2 Storage Card and CPU...
  • Page 8: Step-By-Step Disassembly Instructions

    Heat Sink Processor SSD *12set Network Card *3 Add-On Module DIMM *6Set AIOM Card M.2 *2 2.3 Step-by-Step Disassembly Instructions 1. Removing Cable and Chassis Top Cover 1. Use the operating system to power down the system. 2. After the system has completely shut-down, disconnect the power cords from the power supply modules.
  • Page 9: Removing Hard Disk Drive (Hdd) / Solid State Drive (Sdd)

    Description Description Power Cable Chassis BMC LAN Port Top Cover USB 3.0 Ports VGA Port PCIe 5.0 x16 AIOM Slot (NCSI) 2. Removing Hard Disk Drive (HDD) / Solid State Drive (SDD) 1. Press the release button to extend the drive carrier handle. 2.
  • Page 10: Removing Power Supply

    and lift the SSD out from the posts as shown below: 5. Use a cross screwdriver to remove the drive enclosure 6. Use a cross screwdriver to remove screws and lift off the PCB Description HDD/ SSD Hard Drive Enclosure Hard Drive PCB 3.
  • Page 11 1. Press the release tab on the power supply. 2. Use the handle to gently slide the power supply out the back of the chassis. 3. Remove the screw from the enclosure 4. Cut the power leads connected to the fan and lift the main board from the chassis...
  • Page 12: Removing Advanced I/O (Aiom) Network Card

    Use a flathead screwdriver to cut the capacitor adhesive and pin solder. Adhesive Description Power Supply Power Enclosure Fan Cable Power Module PCB Capacitor 4. Removing Advanced I/O (AIOM) Network Card 1. Loosen the thumbscrew (circled in red) using your hand. 2.
  • Page 13: Removing Aiom Cable

    5. Removing AIOM Cable 1. Unscrew the two screws (circled in red) using a screwdriver and loosen the thumb screw by hand. 2. Remove the cable from the motherboard. Thumb Screw Description AIOM Cable 6. Removing Add-on Module (AOM) 1. Loosen the thumbscrew and press down on the push pin. 2.
  • Page 14: Removing Backplane

    2. Squeeze the fan tab as circled in red and lift the fan housing up and out of the chassis for each fan. Description Cooling Fans 8. Removing Backplane 1. Ensure all cables are disconnected from the backplane and unscrew the backplane bracket from the Chassis on each side as shown.
  • Page 15: Removing The Riser Bracket And Riser Card

    3. Unscrew the 4 screws (circled in red) to remove the backplane from the backplane bracket. Description Backplane 9. Removing the Riser Bracket and Riser Card 1. Disconnect any cables connecting the riser cards to the system. 3. Press the blue tab on the riser card and lift the riser card bracket away from the chassis 4.
  • Page 16 1. Removing the PHM (Processor Heatsink Module ) from the motherboard, first shut down the system and unplug the AC power cord from all power supplies 2. Use a T30-bit screwdriver to loosen the four peek nuts on the heatsink in the sequence of 6,5,4,3,2,1 as shown in the picture below: 10.1 3.
  • Page 17: Removing Dimm

    10.2 Processor 11. Removing DIMM 11.1 1. Hand press both release tabs on the ends of the DIMM module to unlock it 2. Once the DIMM module is loose, remove it from the memory slot Description 11.1 DIMM 12. Removing the Network Card 1.
  • Page 18: Removing The Power Supply Shroud And Air Shroud

    13.1 J7 Connector Description 13.1 14. Removing the Power Supply Shroud and Air Shroud 1. Locate the Power Supply Shroud on the motherboard and lift it out of the system by using the latch. 14.1 2. Locate the Air Shroud on top of the motherboard and lift it out of the system. 14.2 Description...
  • Page 19: Removing Motherboard

    14.1 Power Supply Shroud 14.2 Air Shroud 15. Removing Motherboard 1. Unscrew the screws (circled in red) on the motherboard and lift the motherboard out of the chassis. 2. Push aside the small clamp that covers the edge of the battery. When the battery is released, lift it out of the holder.
  • Page 20 Remove control panel screw (R and L) from the chassis. 16.1 16.2 Remove backet screw and hand screw (R and L) from control panel and used hand remove backet mylar. Description 16.1 Control Panel Cover L & R 16.2 MYLAR_L & R When all the steps are complete, the chassis enclosure can be recycled.

Table of Contents