Table of Contents
Advertisement
English
Transporting the Planer (Fig A)
WARNING: For your own safety, it is recommended
that two people carry this machine or serious injury
could result.
When moving your planer, hold it by the side carrying
handles
2
or by the base handles
Bench Mounting (Fig. A)
To facilitate bench mounting, two different sized holes
are provided on the four corners of your planer as shown in
Figures A. If mounting the planer with bolts, use the larger
holes. If mounting the planer with nails or screws, use the
smaller holes. It is not necessary to use both sets of holes.
Always mount your planer firmly to a secure surface to prevent
movement. To enhance the tool's portability, it can be mounted
to a piece of 12.7 mm (1/2") or thicker plywood which can then
be clamped to your work support or moved to other work areas
and reclamped.
nOTE: If you elect to mount your planer to a piece of plywood,
make sure that the mounting screws don't protrude from
the bottom of the wood. The plywood must sit flush on the
work support.
CAUTION: The mounting surface should not be warped or
otherwise uneven.
ASSEMBLY AND ADJUSTMENTS
WARNING: Do not remove guards (
injury could result.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
To Attach the Depth Adjustment Crank
Handle (Fig. A)
1. Remove the screw located in the crank handle shaft.
2. Insert the crank handle
3. Secure in place with the screw and T-wrench
Dust Ejection Ports (Fig. C)
Your planer comes with a dust ejection port. The round port
as shown in Figure. C is for use with a dust collector hose no less
than 200 mm (8").
To Set Up Dust Ejection (Fig. C)
WARNING: Do not operate your planer without the
dust ejection port locked into place. Do not insert
anything into the dust ejection chute unless the
planer is unplugged and you are clearing a clog or
obstruction in the unit. Do not get your face or eyes
near the dust ejection port when the planer is in
operation. Serious injury could result.
WARNING: A hose no less than 200 mm (8") in length
MUST be used on the dust ejection port in order to
avoid injury.
8
3
at the base of the planer.
12
, Fig. B). Serious
over the shaft.
5
7
provided.
WARNING: Chips are ejected at significant velocity.
Keep hands and face clear of dust ejection port.
1. Select the port
2. Depress the lock button
3. Slide the notches in the dust port over the pins on the chip
ejection chute.
4. Rotate the port until the button engages the dust ejection
chute and locks in place.
4
To Remove the Dust Ejection Port
1. Use the T-wrench to depress the lock button
dust chute.
2. Twist the port until the pins are disengaged from the
notches on the port.
3. Pull the dust ejection port off of the dust chute.
OPERATION
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
On/Off Switch (Fig. A, D)
The on/off switch switch
advantages.
•
No-volt release function: should the power be shut off for
any reason, the switch has to be deliberatley reactivated.
•
To switch the machine on, press the green start button.
•
To switch the machine off, press the red stop button.
Depth Adjustment
Depth Adjustment Scale (Fig. A, E)
The depth adjustment scale
your planer, indicates the finished thickness of your workpiece.
One rotation of the depth adjustment crank is equal to 1.6 mm
(1/16"), half rotation is equal to 0.8 mm (1/32"), etc.
Depth Adjustment Crank (Fig. A, E)
Turning the crank
14
the crank counterclockwise raises the cutterhead.
Turret Stop (Fig. F)
Your planer is equipped with a turret stop
planing at pre-set depths. Stops are set at 3 mm (1/8"), 6.5 mm
(1/4"), 12.5 (1/2"), 19 mm (3/4"), 25.5 mm (1"), and 32 mm
(1-1/4").
To Set the Minimum Depth to Which the Carriage
Can Travel with the Turret Stop
1. Be sure the carriage is set above 32 mm (1-1/4") before
trying to set the turret stop.
2. Turn the dial on the front left of the planer until the desired
thickness setting aligns with the red indicator, then lower
the carriage.
.
14
15
on the chip ejection chute
6
of your saw bench offers multiple
, located on the right front of
8
5
clockwise lowers the cutterhead. Turning
9
13
.
15
on the
for repetitive
Advertisement
Table of Contents
