DeWalt DW735-XE Original Instructions Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Planer
  5. DW735-XE
  6. Original instructions manual
DeWalt DW735-XE Original Instructions Manual

DeWalt DW735-XE Original Instructions Manual

Hide thumbs Also See for DW735-XE:
Table of Contents

Advertisement

Quick Links

Download this manual
DW735-XE

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DW735-XE

Summary of Contents for DeWalt DW735-XE

  • Page 1 DW735-XE...
  • Page 2 English (original instructions) Copyright D WALT...
  • Page 3 Fig. A Fig. B Fig. C Fig. D...
  • Page 4 Fig. E Fig. F Fig. G Fig. H Fig. I Fig. J Fig. L Fig. K Top Flat BOWED WOOD WILL BE FLATTENED BY FEED ROLLERS AND CUTTERHEAD… Bottom flat ...BUT BOW WILL RETURN AFTER WOOD IS PLANED...
  • Page 5 Fig. N Fig. M Fig. P Fig. O Fig. R Fig. Q...
  • Page 6 Fig. S Fig. T Fig. U Fig. V Fig. W Fig. X Fig. Y Fig. Z...
  • Page 7 English HEAVY-DUTY PORTABLE THICKNESS PLANER DW735-XE Congratulations! Definitions: Safety Guidelines You have chosen a D WALT tool. Years of experience, thorough The definitions below describe the level of severity for each product development and innovation make D WALT one of the signal word.

  • Page 8: Personal Safety

    English c ) Do not expose power tools to rain or wet conditions. b ) Do not use the power tool if the switch does not turn Water entering a power tool will increase the risk of it on and off. Any power tool that cannot be controlled electric shock.

  • Page 9: Electrical Safety

    English Date Code Position • Always locate planer with proper clearance on the outfeed side of the unit to prevent pinching or binding of the workpiece The date code, which also includes the year of manufacture, is against any obstacle. printed into the housing.

  • Page 10: Assembly And Adjustments

    English Transporting the Planer (Fig A) WARNING: Chips are ejected at significant velocity. Keep hands and face clear of dust ejection port. WARNING: For your own safety, it is recommended 1. Select the port   14  that two people carry this machine or serious injury 2.
  • Page 11 English 3. Plane the workpiece at desired increments until the correct To Plane Your Material final thickness is achieved. 1. Lower the carriage to the desired height for your first pass. nOTE: Do not use force to crank the carriage below the 2.

  • Page 12: Periodic Maintenance

    English Changing or Rotating the Planer Knives To Plane Twisted Wood (Fig. I) WARNING: Twisted wood may jam your thickness WARNING: To reduce the risk of serious personal planer. If a jam occurs, turn the power off, disconnect injury, disconnect the planer from the power source the power supply and raise the carriage to release before attempting to change or access the knives.
  • Page 13 English After Installing New Knives nOTE: Circuit breaker overload is often the result of dull knives. Change your knives on a regular basis to avoid tripping your 1. Insert the round end of the dust shroud into the fan housing breaker.

  • Page 14: Protecting The Environment

    English • DW7350 Mobile Stand WARNING: For your own safety, it is recommended that two people carry this machine or serious injury • DW7351 Folding Tables could result. • DW7352 325 mm Knives To Remove the Tables • DW7353 Chip Ejection Accessory nOTE: Helical cutterheads have not been tested with this 1.

  • Page 15: Troubleshooting Guide

    Troubleshooting Guide Problem Possible Cause Possible solution If the material does not feed properly Check for dull knives. Rotate or replace as necessary. Refer to Changing or Rotating the Planer Knives section. Check for excess clogging in the dust ejection Refer Dust Ejection Port paragraphs in the Assembly and port.
  • Page 16 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)

Table of Contents