Download
Share
Print this page
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Planer
  5. DW734-XE
  6. Instruction manual

DeWalt DW734-XE Instruction Manual

318 mm (12-1/2”) heavy duty portable thickness planer
Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
D
WALT Industrial Tool Pty. Ltd..,20 Fletecher Road Mooroolbark,Victoria, Australia 3138
(MAY03) Form No. 620422-00
DW734
E
Copyright © 2003
The following are trademarks for one or more D
WALT power tools: the yellow and black color scheme; the "D" shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of
E
lozenge-shaped humps on the surface of the tool.

Advertisement

loading

Related Manuals for DeWalt DW734-XE

Summary of Contents for DeWalt DW734-XE

  • Page 1 WALT Industrial Tool Pty. Ltd..,20 Fletecher Road Mooroolbark,Victoria, Australia 3138 (MAY03) Form No. 620422-00 DW734 Copyright © 2003 The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
  • Page 2 INSTRUCTION MANUAL DW734-XE 318 mm (12-1/2”) Heavy Duty Portable Thickness Planer...

  • Page 3: General Safety Instructions

    SAVE THESE INSTRUCTIONS MINIMUM GAGE FOR CORD SETS • Never clear clogs, make cutter knife replacement or any other Volts Total Length of Cord in Feet repairs/adjustments with unit plugged in. IMPORTANT SAFETY INSTRUCTIONS FOR ALL 240V 0-50 51-100 101-200 201-300 •...

  • Page 4: Specifications

    Voltage decrease of Before using your planer, fold down the table extensions in the front more than 10% will cause loss of power and overheating. All DeWalt and back of the tool (Fig. 7). After extended use, the table extensions tools are factory tested, if this tool does not operate, check the power may be slightly out of level.
  • Page 5 FIG. 8 FINE ADJUSTMENTS NOTE: DO NOT USE FORCE TO CRANK THE CARRIAGE BELOW THE LEVEL THAT THE TURRET STOP INDICATES. PERMANENT The depth adjustment handle allows for fine adjustments, from DAMAGE TO THE HEIGHT ADJUSTMENT SYSTEM ON YOUR .40mm (1/64”) to 1.6mm (1/16”.) PLANER WILL RESULT.
  • Page 6 MINIMUM/MAXIMUM WIDTH/HEIGHT/DEPTH CHANGING THE PLANER KNIVES FIG. 12 NOTE: There is a certain area on the carriage of your planer that will WARNING: DISCONNECT THE PLANER FROM THE POWER allow the 3.18mm (1/8”) depth of cut on material less than 152.4mm SOURCE BEFORE ATTEMPTING TO ACCESS OR CHANGE THE (6”) wide.
  • Page 7 MAINTENANCE between the material and the table while providing adequate support at the two points (those farthest from the cutter head) on the tables that INSTALLING A NEW BELT are integral to snipe prevention. NOTE: No tools are necessary to install a belt. The use of a screwdriver TABLE or other tool to pry or stretch a belt may cause damage to the pulleys Keep the table clean and free from oil, grease and pitch.
  • Page 8 30 Day No Risk Satisfaction Guarantee FIG. 22 f you are dissatisfied with any D WALT power tool , for any reason, simply return it to the point of purchase with your sales receipt within 30 days for a replacement unit or full refund. INFORMATION HOTLINE When you need further information on a D WALT product please phone:...

  • Page 9: Troubleshooting Guide

    TROUBLESHOOTING GUIDE IF THE MATERIAL DOES NOT FEED PROPERLY, CHECK FOR: • excess clogging in the dust hood. • excess oil/debris/pitch on feed rollers. • excessively twisted, cupped or bowed material. • a broken drive belt. • dull knives. IF THE CIRCUIT BREAKER TRIPS REPEATEDLY: •...