Related Manuals for ProLights ARCSPOT M VW
Summary of Contents for ProLights ARCSPOT M VW
- Page 1 ARCSPOT M VW IP66 Spot featuring 4100 lumen with 19x 4W Variable White source, 10° native USER MANUAL English version REV.01-02/24 PRELIMINARY...
- Page 2 PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its affiliates, and subsidiaries. PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc - 04026 - Minturno (LT) ITALY.
-
Page 3: Table Of Contents
LENS (CODE ASLENS15/25/45 - OPTIONAL) ..............22 BRACKET FOR WALL MOUNTING AND SUSPENSION ON POLES (CODE MOSUNIBRACKJR) ......................25 13 - MAINTENANCE MAINTENANCE AND CLEANING THE PRODUCT............26 VISUAL CHECK OF PRODUCT HOUSING ..............26 14 - TEST OF IP66 RATING PROLIGHTS - ArcSpot MVW... -
Page 4: Safety Information
• Do not reapply power until repairs have been completed. • Refer any service operation not described in this manual to PROLIGHTS Service team or an authorized PROLIGHTS service center. - Page 5 • Warning! Disconnect the fixture from AC mains power and allow to cool for at least 10 minutes before handling. • Only technicians who are authorized by PROLIGHTS or Authorised service partners are permitted to open the fixture. • Users may carry out external cleaning, following the warnings and instructions pro- vided, but any service operation not described in this manual must be referred to a qualified service technician.
- Page 6 • This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. PROLIGHTS - ArcSpot MVW...
-
Page 7: Packaging
Check the updated accessories list, description and informations of the product at the following link: https://www.prolights.it/product/ARCSPOTMVW#accessories 2 - TECHNICAL DRAWING 210mm 123mm 177mm [8.3in] [4.8in] [7.0in] 188mm Ø280mm [7.4in] [11.0in] Fig. 01 Weight: 2,7 kg - 5,95 lbs PROLIGHTS - ArcSpot MVW... -
Page 8: Installation
NOTE: In external installations it is advisable to mount the product with the cables facing downwards to avoid water or humidity deposits which can compromise functionality in the long term. C6002 Steel security cable clamp 38 mm 76 mm Ø13 mm [1.5 in] [3.0 in] [Ø0.5 in] Fig. 02 PROLIGHTS - ArcSpot MVW... -
Page 9: Product Overview
4. DMX IN (4-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5. 5. POWER IN: for connection to the Mains 100-240V~/50-60Hz. 6. DMX OUT (4-p XLR): 1 = GND, 2 = sign-, 3 = sign+, 4 N/C, 5. Fig. 03 PROLIGHTS - ArcSpot MVW... -
Page 10: Connection To The Mains Supply
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz). • The product is then ready for its operations and can be controlled through the available input sig- nals on board. • To disconnect power from the product, disconnect the Mains from the socket. PROLIGHTS - ArcSpot MVW... -
Page 11: Dmx Connection
Install a DMX termination plug on the last fixture on the link. If a splitter is used, terminate each branch of the link. NOTE: when not using the DMX input or DMX output connectors, you must seal the cable ends with the supplied caps. PROLIGHTS - ArcSpot MVW... -
Page 12: Connection Of The Dmx Line
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the male XLR connector, as shown in figure. Pin1 : GND - Shield (Black) Pin2 : - Signal (Yellow) Pin3 : + Signal (Red) Pin4 : Auto-addressing (White) Example: 5 pin XLR connector Fig. 07 PROLIGHTS - ArcSpot MVW... -
Page 13: Operation Via Datamaster
... . DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT DMX OUT DATAMASTER Fig. 04 - Example 12 DMX channels configuration Fig. 08 PROLIGHTS - ArcSpot MVW... -
Page 14: Rdm Menu Structure
To see the unit temperature. TEMP, DRIVER PCB TEMP, LED PCB TEMP,… SOFTWARE View informations about software VERSION version. DEVICE INFO View informations about device. DEVICE LABEL Show RDM Device label. RDM UID View ID for the RDM control. PROLIGHTS - ArcSpot MVW... - Page 15 5600K 6000K 6500K MANUAL WARM WHITE DIMMER:0-255 User generated color preset by assigning values to each primary color attribute. After enabled this mode, the unit will be COLD WHITE DIMMER:0-255 automatically assigned as Master. FACTORY DEFAULT PROLIGHTS - ArcSpot MVW...
-
Page 16: Rdm Functions
0x0121 DEFAULT_SLOT_VALUE 0x0122 SENSOR_DEFINITION 0x0200 Sensors SENSOR_VALUE 0x0201 CURVE 0x0343 CURVE_DESCRIPTION 0x0344 OUTPUT_RESPONSE_TIME 0x0345 OUTPUT_RESPONSE_TIME_ DESCRIPTION 0x0346 MODULATION_FREQUENCY 0x0347 MODULATION_FREQUENCY_ DESCRIPTION 0x0348 DEVICE_HOURS 0x0400 LAMP_HOURS 0x0401 LAMP_STRIKES 0x0402 Power/Lamp Settings LAMP_STATE 0x0403 LAMP_MODE 0x0404 DEVICE_POWER_CYCLES 0x0405 PROLIGHTS - ArcSpot MVW... - Page 17 0x82C7 0-255 CURRENT HOURS 0x82C5 POWER CONSUMPTION(AC 220V) 0x82EF 10-300 DEFAULT: 300 MAINTENANCE TIME:ALERT PERIOD 0x82DF DEFAULT: 0 MAINTENANCE TIME:ELAPSED TIME 0x82E0 ERROR MESSAGES 0x82EA 0: No Error 0: No CLEAN ALL DATA 0x82C8 1: Yes PROLIGHTS - ArcSpot MVW...
-
Page 18: Dmx Charts
11 - DMX CHARTS RDM Model ID: 0xD137 RDM Personality ID List DMX Mode Footprint 4CH1 4CH1 4CH2 4CH2 MODE PARAMETER 4CH1 4CH2 DIMMER DIMMER FINE STROBE CROSSFADE WARM WHITE COLD WHITE RESERVED CONTROL PROLIGHTS - ArcSpot MVW... - Page 19 3200 3300 3300 3400 3400 3500 3500 3600 3600 3700 3700 3800 3800 3900 3900 4000 4000 4100 4100 4200 4200 4300 4300 4400 4400 4500 4500 4600 4600 4700 4700 4800 4800 4900 4900 5000 PROLIGHTS - ArcSpot MVW...
- Page 20 Default @ 0 Warm White 8 bit value 16 bit value Function Note From From DIMMER Default @ 255 Cold White 8 bit value 16 bit value Function Note From From DIMMER 65535 Default @ 255 PROLIGHTS - ArcSpot MVW...
- Page 21 DMX FAULT STAND ALONE STAND ALONE MASTER DMX STAND ALONE MASTER NO DMX STAND ALONE SLAVE STAND ALONE EFFECTS STAND ALONE FIXED COLORS STAND ALONE WHITE PRESETS STAND ALONE MANUAL CW+WW RESERVED RESET ALL CHANNEL CONTROLLED RESERVED PROLIGHTS - ArcSpot MVW...
-
Page 22: Accessories Installation
12 - ACCESSORIES INSTALLATION HALF SNOOT (CODE ARMHSNOOTGY - OPTIONAL) Place fixture on a stable surface. 1. Remove rubber caps (A). Insert the Half snoot (B). 2. Screw the supplied screws (C) to secure the accessory. PROLIGHTS - ArcSpot MVW... -
Page 23: Honeycomb Louvre (Code Arxlhlouvregy/Wh - Optional)
HONEYCOMB LOUVRE (CODE ARMHLOUVREGY - OPTIONAL) Place fixture on a stable surface. 1. Remove rubber caps (A). Insert the Honeycomb louvre (B). 2. Screw the supplied screws (C) to secure the accessory. NOTE: the images refers to ARCSPOTXL PROLIGHTS - ArcSpot MVW... -
Page 24: Lens (Code Aslens15/25/45 - Optional)
LENS (CODE ASLENS15/25/45 - OPTIONAL) Place fixture on a stable surface. • Remove the rubber caps (A), then unscrew the metal front ring screws (B). • Remove the metal front ring (C). Fig. 12 PROLIGHTS - ArcSpot MVW... - Page 25 Turn the fixture with lenses upside and proceed as follows: • Unscrew the lenses holder screws (D). • Remove the lenses holder (E). NOTE: be careful to match the spaces in the same way as they are disassembled to close the product correctly. Fig. 12 PROLIGHTS - ArcSpot MVW...
- Page 26 Gently replace each lens as shown in figure, Fig. 12 PROLIGHTS - ArcSpot MVW...
-
Page 27: Bracket For Wall Mounting And Suspension On Poles (Code Mosunibrackjr)
IP grade of the fixture. • All other service operations on the product must be carried out by PROLIGHTS, its approved service agents or trained and qualified personnel. -
Page 28: Maintenance
It is recommended to verify IP grade using IPTESTBOX every time the bodies are removed for maintenance. Remove the gore valve from the rear cover. Connect the air hose to the IPTESTBOX by inserting the quick-connect fitting into the coupler. PROLIGHTS - ArcSpot MVW... - Page 29 Insert the threaded end into the threaded valve hole socket. For the operating procedure using the instrument, refer to the IPTESTBOX user manual. PROLIGHTS - ArcSpot MVW...
- Page 30 Note...
- Page 32 PROLIGHTS is a trademark of prolights.it Via A.Olivetti snc MUSIC & LIGHTS S.r.l. support@prolights.it 04026 - Minturno (LT) ITALY musiclights.it Tel: +39 0771 72190...