Page 2
1 . Setting up Machine for Work B . Installing Thread Stand C. Connecting Motor Controller D . Assembly of knee Lifter 2 . Lubrication ............... . 4 3 . Nee<lles and Thread ............5 4 .
Page 3
IN DEX <INSTRUCTION MANUEL> -=-' ll!I, H an d wh ee l Rotation and S p eed ··············· ········· ··· ··· ··· ··· ··· 2 1\, Oilling a nd Ma i n te nance ··· ··· ··· ··············· ······ ··· ······ · ·· ··· ··· 3 -t, Th re adi ng Mac hi ne ···...
Page 4
<INSTRUCTION MANUEL> I N D EX ... U n p ac kin g Machin e ··· ··· · ·· ··· ··· ··· ··· ··· ··· ··· ·· · ··· ··· 1 _, Settin g -u p Mac hin e ··· ··· ··· ··· ··· ·· · ··· ··· ··· ··· ·· · ··· ··· 1 _, Install linin g rac k ···...
Page 5
Unpack machine from its shipping box.making certain that you remove from box all component parts and accessories.Do not disoard any packing material without prior scrutiny as to contents. Clean from machine all greases,dirt,or dust. Pay particular attention to area around the looper machanism and looper.
Page 6
Turn hand wheel only in direction away from operator for cl ockwise rotation.Be sure motor drive is wired up to obtain the same clockwise rotation.However,the recommanded operating speed of a brand new machine l ,300- l ,500stitches per minute.After a breaking-in period of several weeks and after the operator has become skilled in the operation of the machine,the speed can be increased upto 1,800 stitches per minute.
Page 7
. 3. It is important to operate the machine before oil of good qu ality has been filled in each and evey oil hole along the top of the machine. When breaking-in a new machine oiling should be done sparingly several times a day.Thereafter,one oiling daily will be sufficient.After oiling, wipe machine carefully to avoid soiling of the material.
Page 8
I .Scissor the material,which makes the front material form triangle cloth with the length of 1 00mm(Fig.4) Triangle material 2.Press the rod.Leave the space between presser foot and fe eding material retainer.Rotate the belt wheel, which makes front and rear feeding teeth rise. Feed the material into the front part of the feeding teeth with feeding cutter.
Page 9
3.Lining cloth is installed on the big bulley.(Fig. l)Clamp the front part of the lining cloth with the clamp.Then above the main material.(Fig.6) Notice:The lining cloth needn't be used when mid-thick material trousers ears are made. Main material Fig.6 4.Check whether the position of the material and lining cloth are right.Start the machine slowly.Hold the material stably.Then begin to sew.
Page 10
The type of material to be blindstitched governs degree of needle penetration is required.It is ,therefore.recommended to stitch a few centimeters as a test and make adjustments for pene tration depending on the appearance of the trial stitching. Turn regulator clockwise for less penetration and counter clockwise for more penetration(Fig.8) ...
Page 11
Needle Recommendation The recommended needle is system LW X 6T. Material Size Cottons,Silks,Acetates,Orion,Dacron and similar type of light weight fabrics. Medium weight materials, Wollens and Others. Thick materials for coats,house furnishings. Taking out the sewed material After sewing finished,stop the operation.Rotate the upper wheel clockwise, which makes the needle away from the material.
Page 12
2.Left,right cutters regulation Rotate the hand wheel clockwise until cutters get to the bolt until the edge of the left and right cutters is 1 mm above the lower edge of the above blade. Then twist the screws tightly.(Fig.11) Left and right cutter cover Fig.
<PARTS LIST> CONTENTS M achine Frame&C o v ers C ompo n e n ts ··· ··· ······ ········ ······· ······· ········ ······ ···2 M ain Shaft Mech ani s m C omponents ··· ··· ··· ··· · ·· ··· ··· ·· · ··· ·· · ······ · ·· ·· · ··· ··· ···4 Needle Carrier&Feed Dog Mechanism Components ···...
Description Re£NO. Parts NO . Arm Side Cover 4139 Arm Side Cover Set Screw 4144-A Arm Side Cover Plate 4137 5227 Arm Side Cover Plate Screw Arm Top Cover Plate Arm Top Cover Plate Screw 4141 4140 Arm Top Cover Plate Washer Thread Guide 4203-A 4193...
Page 29
3C-53 Leaf Spring Set Screw 6C-54 Leaf Spring (short) 6C-53 Leaf S rping(long) 8G-30 Feed Dog Washer 2B-17 Ball Connecting Rod Set Screw(A) 3E-24 6C-51 Connecting Roel Hoding Screw(A) 3C-2 Ball Connecting Rod Set Screw(B) 6C-52 Connecting Roel Hoding Screw(B) 8-10 3E-24 Machine Base Nut...