Smeg PVA140 Manual
  1. Manuals
  2. Brands
  3. Smeg Manuals
  4. Hob
  5. PVA140
  6. Manual
Smeg PVA140 Manual

Smeg PVA140 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
1. Instructions for safety and use ________________________ 20
2. Positioning in the counter top _________________________ 21
2.1 Fixing to the supporting structure _______________________________________21
2.2 Positioning the adhesive sponge _______________________________________22
2.3 Positioning the fastening clips _________________________________________22
3. Electrical connection _______________________________ 23
4. Gas connection ___________________________________ 24
4.1 Connection to liquid gas ______________________________________________24
4.2 Room ventilation ____________________________________________________24
4.3 Extraction of the combustion products ___________________________________24
5.1 Removing the hob top________________________________________________25
5.2 Adjustment for liquid gas _____________________________________________26
5.3 Adjustment for natural gas ____________________________________________27
5.4 Primary air adjustment _______________________________________________27
5.5 Re-assembling the hob top____________________________________________28
5.7 Adjusting the minimum setting for liquid gas_______________________________28
5.8 Arrangement of the burners on the hob __________________________________28
5.9 Lubrication of gas taps _______________________________________________28
6. Description of the controls ___________________________ 29
6.1 The front panel _____________________________________________________29
7. Using the hob _____________________________________ 30
7.1 Positioning the racks_________________________________________________30
7.2 Lighting the burners using a safety device ________________________________32
7.3 Practical tips for using the burners ______________________________________32
7.4 Pan diameters______________________________________________________32
8. Cleaning and maintenance __________________________ 33
8.1 Cleaning the hob____________________________________________________33
8.3 Cleaning parts______________________________________________________33
THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES WHOSE
IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS MANUAL.
THIS IS A CLASS 3 BUILT-IN HOB.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
technician who must carry out an adequate inspection of the gas system, install the
appliance, set it functioning and test it.
INSTRUCTIONS FOR THE USER: these contain user advice, a description of the
commands and the correct procedures for cleaning and maintenance of the appliance.
Contents
19

Advertisement

Table of Contents
loading

Related Manuals for Smeg PVA140

Summary of Contents for Smeg PVA140

  • Page 1: Table Of Contents

    THIS IS A CLASS 3 BUILT-IN HOB. INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must carry out an adequate inspection of the gas system, install the appliance, set it functioning and test it. INSTRUCTIONS FOR THE USER: these contain user advice, a description of the...

  • Page 2: Instructions For Safety And Use

    Instructions for safety and use Instructions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE YOU TO READ THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN CAREFULLY BEFORE USING THE HOB.

  • Page 3: Positioning In The Counter Top

    If the hob is installed on top of an oven, the latter must be equipped with a cooling fan. In case of installation on an empty kitchen unit with doors, a separation panel must be placed under the hob.

  • Page 4: Positioning The Adhesive Sponge

    (fig. B). 2.4 Inserting the hob into the hole in the work surface Be very careful when inserting the hob. If the process is not followed correctly as described, the hob may be damaged. Before inserting it, remove the racks (if they are mounted) and burners from the hob.

  • Page 5: Electrical Connection

    Do not remove this plate for any reason. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations. Make sure that the supply line is suitably earthed.

  • Page 6: Gas Connection

    The hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. To set it up for supply using other types of gas, see “5. ADAPTATION TO DIFFERENT TYPES OF GAS”.

  • Page 7: Adaptation To Different Types Of Gas

    The appliance must not be built in and connected to the supply before the following operations have been completed. The cooker hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. If other types of gas are to be used, the nozzles must be replaced and the primary air must be adjusted.

  • Page 8: Adjustment For Liquid Gas

    Instructions for the installer 5.2 Adjustment for liquid gas Unscrew screw C and push air regulator D as far as it will go. Using a 7-mm wrench, remove nozzle E and replace with appropriate nozzle, following the instructions in the tables for the type of gas to be used.

  • Page 9: Adjustment For Natural Gas

    5.3 Adjustment for natural gas The hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. To reset the appliance for operation with this type of gas, carry out the same steps as described in “5.2 Adjustment for liquid gas”, but select the nozzles and adjust the primary air for natural gas as indicated in...

  • Page 10: Re-Assembling The Hob Top

    The by-pass diameters for each individual burner are given in “5.2 Adjustment for liquid gas”. After adjustment with a gas other than the preset one, replace the label on the casing of the appliance with the label corresponding to the new gas. The label is located inside the GPL nozzle pack (G30 –...

  • Page 11: Description Of The Controls

    4-burner hob KNOB DESCRIPTION To light the flame, press the knob and, at the same time, turn it anticlockwise to the minimum flame symbol . To adjust the flame, turn the knob to the zone between the maximum ( ) and minimum ( ) settings.

  • Page 12: Using The Hob

    The holes C in the burner should be slid over the igniters and thermocouples D on the hob. 7.1 Positioning the racks The racks are provided separate unassembled on the hob. To position each rack correctly on its burner, follow the instructions below: Each rack...
  • Page 13 CORRECT Having completed the procedures described above (for each of the racks), the hob will be as shown below, with the rack legs arranged in a pattern of horizontal and vertical lines. If you find that a pan is particularly unstable, make sure that the racks have not...

  • Page 14: Lighting The Burners Using A Safety Device

    When the burner is lit, the relevant activation knob will light up to indicate this. The knob will turn off a few seconds after it is turned to the O position or if the burner goes out accidentally. The knob light turns on and off gradually.

  • Page 15: Cleaning And Maintenance

    Do not use a steam jet for cleaning the appliance. 8.1 Cleaning the hob To keep the hob in good condition it should be cleaned regularly after use. Let it cool first. 8.1.1 Ordinary daily cleaning of the glass surfaces To clean and preserve the glass surfaces, always use only special products that do not contain abrasives or chlorine-based acids.
  • Page 16 The burner pins A must be inserted in the housings B in the burner crown. The holes C in the latter should be slid over the igniters and thermocouples D on the hob.

This manual is also suitable for:

Pva140-1

Table of Contents