These instructions apply only for the destination countries listed on the appliance's data plate. This is a class 3 built-in hob. We advise you to read this manual carefully, which contains all the instructions for maintaining the appliance’s aesthetic and functional qualities. For further information on the product: www.smeg.com...
Instructions 1 Instructions • Cleaning and maintenance must not be carried out by 1.1 General safety instructions unsupervised children. • Have qualified personnel carry Risk of personal injury out installation and assistance • During use the appliance and its interventions according to the accessible parts become very hot.
Instructions • Never leave the appliance 1.5 Disposal unattended during cooking This appliance must be disposed of operations where fats or oils separately from other waste could be released. (Directives 2002/95/EC, 2002/ 96/EC, 2003/108/EC). The appliance • Never leave objects on the does not contain substances in quantities cooking surface.
Instructions Our appliances are packaged in non- 1.7 How to read the user manual polluting and recyclable materials. This user manual uses the following reading • Deliver the packing materials to the conventions: appropriate recycling centre. Instructions Plastic packaging General information on this user Danger of suffocation manual, on safety and final disposal.
Description 2 Description 2.1 General Description 65 cm 75 cm 90 cm AUX = Auxiliary R = Rapid SR = Semi-rapid UR = Ultra rapid RR = Reduced rapid UR* = Ultra rapid...
Description 2.2 Symbols 2.3 Available accessories Cooking zones WOK ring Front left Centre left Rear left Central Useful when using a wok. Rear right The accessories intended to come Central right into contact with food are made of materials that comply with the Front right provisions of current legislation.
3 Use Improper use 3.1 Instructions Risk of damage to surfaces Improper use • Do not use aluminium foil to cover the Danger of burns burners or hob body. • Cooking vessels or griddle plates • Make sure that the flame-spreader should be placed inside the perimeter of crowns are correctly positioned in their the hob.
3.3 Using the hob Correct positioning of the flame- spreader crowns and burner caps All the appliance’s control and monitoring devices are located together on the front Before lighting the hob burners, make sure panel. The burner controlled by each knob that the flame-spreader crowns are is shown next to the knob.
Page 9
Correct positioning of the grids Practical tips for using the hob Under the grids there are silicone rests with For better burner efficiency and to minimise a hole that must be centred onto the gas consumption, use pans with lids and of matching fixing pins on the surface.
Cleaning and maintenance 4 Cleaning and maintenance 4.2 Cleaning the appliance To keep the surfaces in good condition, 4.1 Instructions they should be cleaned regularly after use. Let them cool first. Improper use Risk of damage to surfaces Ordinary daily cleaning Always use only specific products that do •...
Page 11
Cleaning and maintenance Cooking hob grids Igniters and thermocouples Remove the grids and clean them in For correct operation the igniters and lukewarm water and non-abrasive thermocouples must always be perfectly detergent. Make sure to remove any clean. Check them frequently and clean encrustations.
Installation 5 Installation 5.2 Section cut from the countertop The following operation requires 5.1 Safety instructions building and/or carpentry work Heat production during appliance and must therefore be carried out operation by a competent tradesman. Risk of fire Installation can be carried out on various materials such as masonry, •...
Installation 5.3 Mounting Over empty kitchen unit or drawers If there are other pieces of furniture (lateral Over built-in oven unit walls, drawers, etc.), dishwashers or fridges The clearance between the hob and the under the hob, a double-layer wooden kitchen furniture or other installed base must be installed at least 20 mm from appliances must be enough to ensure...
Page 14
Installation Fixing brackets With steel hob To prevent leakage of liquid between the Screw the fixing brackets (A) into the holes frame of the hob and the work surface, put on the sides of the bottom casing to the insulating seal provided in position properly fasten the hob to the structure.
Installation 5.4 Gas connection Connection with a steel hose Make the connection to the gas mains Gas leak using a continuous wall steel hose whose Danger of explosion specifications comply with the applicable standard. • After carrying out any operation, check Carefully screw the connector 3 to the gas that the tightening torque of gas connector 1 of the appliance, placing the...
Page 16
Installation Connection with a steel hose with conical Connection to LPG fitting Use a pressure regulator and make the Make the connection to the gas mains connection on the gas cylinder following using a continuous wall steel hose whose the guidelines set out in the standards in specifications comply with the applicable force.
Page 17
Installation Extraction of the combustion products 1 Extraction using a hood 2 Extraction without a hood The combustion products may be extracted by means of hoods connected to a natural draught chimney whose efficiency is certain A Single natural draught chimney or via forced extraction.
Installation 5.5 Adaptation to different types of 2. Remove the flame-spreader crowns and relative burner caps. If other types of gas are to be used, the nozzles must be replaced and the primary air must be adjusted. In order to replace the nozzles and adjust the burners, the hob top must be removed.
Page 19
Installation 4. Remove the screws fastening the top and Replacing nozzles the plates corresponding to each burner zone. 1. Unscrew screw A and push air regulator B as far as it will go. 2. Use a spanner to remove the nozzles C and install the new ones for the required gas supply, following the indications 5.
Page 20
Installation Adjusting the minimum setting for natural Adjusting the minimum setting for LPG or town gas Tighten the screw located at the side of the 1. Light the burner and turn it to the minimum tap rod clockwise all the way. position.
Page 21
Installation Gas types and Countries Gas types IT GB-IE FR-BE DE RU DK 1 Natural Gas G20 20 mbar • • • • • • • • • G20/25 20/25 mbar • 2 Natural Gas G20 • 25 mbar 3 Natural Gas G25 25 mbar •...
Installation 5.6 Electrical connection The appliance can work in the following modes: Power voltage • 220-240 V 1N~ Danger of electrocution 220-240V~ 1 mm • Have the electrical connection performed by authorised technical personnel. 20 mm • Use personal protective equipment. 3 x 1 mm²...