Smeg PGF31G Manual
  1. Manuals
  2. Brands
  3. Smeg Manuals
  4. Hob
  5. PGF31G
  6. Manual
Smeg PGF31G Manual

Smeg PGF31G Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

1. INSTRUCTIONS FOR USE..................................................... 24
2. SAFETY PRECAUTIONS........................................................ 26
3. ENVIRONMENTAL RESPONSIBILITY ................................... 28
4. KNOW YOUR APPLIANCE ..................................................... 29
5. USING THE HOB .................................................................... 30
6. CLEANING AND MAINTENANCE .......................................... 32
7. POSITIONING ON THE HOB TOP ......................................... 34
THESE INSTRUCTIONS ARE VALID FOR THOSE COUNTRIES IDENTIFIED BY THE
SYMBOLS REPORTED ON THE COVER OF THIS MANUAL.
INSTRUCTIONS FOR THE USER: these instructions contain user
recommendations, a description of the controls and the correct
procedures for cleaning and maintenance of the appliance.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
technician who must install the appliance, set it functioning and carry out
an inspection test.
Contents
23

Advertisement

Table of Contents
loading

Related Manuals for Smeg PGF31G

Summary of Contents for Smeg PGF31G

  • Page 1: Table Of Contents

    INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified technician who must install the appliance, set it functioning and carry out an inspection test.

  • Page 2: Instructions For Use

    ANY OTHER USE. THE MANUFACTURER CANNOT BE HELD LIABLE FOR USE OTHER THAN AS INDICATED. IF THE APPLIANCE IS INSTALLED ON BOATS OR IN CARAVANS, DO NOT USE IT AS A ROOM HEATER. DO NOT USE THIS APPLIANCE FOR HEATING ROOMS.

  • Page 3: General Instructions

    ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE (OFF) POSITION WHEN YOU FINISH USING THE APPLIANCE NEVER PLACE PANS WITH BOTTOMS WHICH ARE NOT PERFECTLY FLAT AND SMOOTH ON THE COOKING HOB PAN STANDS. NEVER USE PANS WHICH PROJECT BEYOND THE OUTSIDE EDGE OF THE HOB.

  • Page 4: Safety Precautions

    DO NOT REMOVE THIS PLATE ON THE CASING FOR ANY REASON. BEFORE CONNECTING THE APPLIANCE, MAKE SURE THAT IT HAS BEEN SET UP FOR THE TYPE OF GAS THAT WILL BE USED. THIS CAN BE CHECKED BY REFERRING TO THE LABEL APPLIED UNDERNEATH THE CASING BEFORE CARRYING OUT INSTALLATION/MAINTENANCE WORK, MAKE SURE THAT THE APPLIANCE IS NOT CONNECTED TO THE POWER GRID.
  • Page 5 THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY ARE SUPERVISED OR INSTRUCTED BY ADULTS RESPONSIBLE FOR THEIR SAFETY. DO NOT LET CHILDREN GO NEAR THE APPLIANCE WHEN IT IS IN OPERATION OR PLAY WITH IT AT ANY TIME. DO NOT INSERT POINTED METAL OBJECTS (CUTLERY OR UTENSILS) INTO THE SLITS IN THE APPLIANCE.

  • Page 6: Environmental Responsibility

    Therefore, at the end of the products...

  • Page 7: Know Your Appliance

    Instructions for the user 4. KNOW YOUR APPLIANCE Auxiliary Burner (AUX) Rapid Burner (R) Dual Crown Burner (UR2)

  • Page 8: Using The Hob

    For dual burner UR2, place and lock caps G and F perfectly on burner D. This latter, in turn, must be placed and locked into the base B (use pins C as a reference). Rack H is for use with woks.
  • Page 9 Take the greatest care when using fats or oils since they may catch fire if overheated. If the burner flame accidentally goes out, turn off the control knob and wait at least 1 minute before trying to re-light the burner.

  • Page 10: Cleaning And Maintenance

    To clean and preserve the stainless steel surfaces, use only specific products that do not contain abrasives or chlorine-based acids. How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or chamois leather.
  • Page 11 A in the flame-spreaders are aligned with the igniters and thermocouples. For dual burner UR2, place and lock caps G and F perfectly on burner D. This latter, in turn, must be placed and locked into the base B (use pins C as a reference).

  • Page 12: Positioning On The Hob Top

    The following operation requires building and/or carpentry work and must therefore be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat-resistant (T 90°C). Built-in dimensions...
  • Page 13 Fixing to the supporting structure 3 - 4 Carefully position the supplied insulating seal on the outer edge of the hole on the top hob, as indicated in the figure alongside. Try and make it stick to the whole surface by applying light hand pressure.
  • Page 14 Do not remove this plate for any reason. The plug at the end of the supply cable and the wall socket must be of the same type and must conform to the applicable legislation on electrical installations.
  • Page 15 (yellow/green) which is at least 20 mm longer. Only use a H05V2V2-F or similar resistance cable to the maximum temperature of 90°C. Its replacement must be carried out be a specialised technician who must carry out the network connection following the diagram below.
  • Page 16 Once the operation is complete, check the hose fittings for leaks using a soapy solution; never use a flame. The hob is preset for natural gas G20 (2H) at a pressure of 20 mbar. For supplying it with other types of gas, see chapter “8. ADAPTATION TO DIFFERENT TYPES OF GAS”.

  • Page 17: Adaptation To Different Types Of Gas

    Before carrying out the following operations, disconnect the appliance from the power supply The appliance is preset for natural gas G20 at a pressure of 20 mbar. In the case of operation with other types of gas, the burner nozzles must be changed and the minimum flame adjusted on the gas taps.
  • Page 18 “8.1 Replacement of nozzles on the hob” in reverse order. After adjustment with a gas other than the preset one, replace the label on the bottom of the casing with the label corresponding to the new gas. This label is supplied with the appliance (when applicable) or can be obtained from the nearest Authorised Service Centre.
  • Page 19 To adjust the minimum setting with liquid gas, you must tighten the screw inside or next to the tap rod (depending on the model) fully in a clockwise direction. The bypass diameters for each individual burner are shown in table “8.2 Burner and nozzle characteristics table”.

This manual is also suitable for:

Pgf32g

Table of Contents