Table of Contents
Advertisement
Available languages
Available languages
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Positioning the Articulating Head LEDs
(Fig. A, C)
WARNING: Do not to attempt to operate the
articulating head LEDs in the closed position, or with
the lens facing the light box, as the surface the light
may get hot.
The articulating head LED
3
swivels from 0°–270°.
nOTE: The light box is equipped with magnetic sensors. If the
articulating head LED
3
,
5
light box, the articulating head LED
will tun off automatically.
1. To move the left articulating head LED
articulating head LED
from the light box
1
.
2. To adjust the light beam, swivel the left articulating head
LED
5
or right articulating head LED
desired position.
3. When not in use fold the left articulating head LED
articulating head LED
3
stored position, secured in the light box
On/Off Switch (Fig. A, D)
WARNING: The lens gets very hot during use. To
reduce the risk of burns, do not touch hot lens.
WARNING: Keep objects at least 20" (51 cm) away
from the lenses when they are in use to prevent the
objects from overheating.
WARNING: To reduce the risk of fire, keep away from
combustible materials while in operation.
CAUTION: Do not stare into box light lens. Serious eye
injury could result.
nOTE: For best results, make sure your battery pack is fully charged.
1. To turn on the right articulating head LED
LED On/Off button
2
.
2. To turn on the left articulating head LED
LED On/Off button
4
.
3. Each articulating head LED
up to 2000 lumens. Continue to press the On/Off buttons to
change the brightness level.
4. Continue cycling the On/Off buttons until the lights turn off.
,
5
piviots up and down 0°–160° and
is stored with the lens facing the
3
,
5
will not turn on and
5
or right
3
first pull it upwards and away
3
by twisting it into the
with the lens side facing into the
1
.
3
, press the right
5
, press the left
3
,
5
has three brightness levels,
nOTE: The light box is equipped with magnetic sensors. If the
articulating head LED
light box, the articulating head LED
will tun off automatically.
Low Battery Indicator
As the battery nears a fully discharged state, the light will blink
twice. The light will continue to blink twice every 45 seconds
until the battery is fully discharged at which time the light will
turn off. Indication time will vary based on battery pack capacity.
CAUTION: Stop work and replace the battery when
this occurs.
Thermal Protection Mode
In cases of overheating, the articulating head LEDs
output automatically switches to the next lower brightness
setting. If the temperature continues to increase, the light box
will power off until a normal operating temperature is reached.
Top Handle (Fig. A)
This light box
to carry the light box
compartment
Carry Handle (Fig. E)
This DWST08061 has a built in carry handle
you to carry the DWST08061 when not attached to a
ToughSystem® storage box.
Storage Compartment (Fig. F)
5
or right
WARNING: Avoid overfilling the storage
compartment.
WARNING: Do not forcefully attach the light box
onto the storage compartment. If the light box will
not fully close or the latches will not lock easily, ensure the
storage compartment is not overfilled. Remove a few items
and try attaching the light box again. If needed you can
stack the storage compartment on top of the light box.
WARNING: When stacking an additional ToughSystem 2.0
unit on top of the light box, the battery must be removed
first, unless it is smaller than 6Ah.
WARNING: Ensure the light panels are facing down before
stacking another ToughSystem 2.0 unit on top of the light
box to prevent possible activation of the LED lights.
This DWST08061 has a storage compartment
extra batteries, cords or tools.
The light box and the storage compartment are ToughSystem
2.0 compatible and can be stacked together or individually with
all ToughSystem 2.0 products.
1. To access the storage compartment
light box
the stacking latch
storage compartment
2. To install the light box
compartment
storage compartment slot
3
,
5
is stored with the lens facing the
3
,
1
has a built in top handle
1
when not attached to the storage
14
.
1
from the storage compartment
12
and then lift the light box
14
.
1
onto the storage
14
, pivot the light box slot
23
. Press the light box
EnGLIsH
5
will not turn on and
3
lumen
9
that allows you
13
that allows
14
to carry your
14
first unlock the
14
by pressing
1
off the
22
into the
1
down
25
Advertisement
Table of Contents
