Warranty And Service; Care And Storage - Armytek WIZARD C2 WG User Manual

Low battery level. When the battery voltage drops, the brightness will
begin to decrease in steps to ensure the safety of the battery and the
user. When the brightness of the mode (except Firefly and Main1) drops
below approximately 25% from the nominal value, the main LED flashes
2 times. At critical level light output decreases to Firefly.
Warnings
For effective operation of the flashlight we recommend branded
18650 Li-Ion batteries without PCB (unprotected) no more than
70 mm long.
The flashlight can get hot in Turbo and Strobe modes quickly and
discharge the battery with high current. Don't leave it without your
attention as very bright light might heat objects and cause fire.
For storage or transportation of the flashlight in a pocket or a bag
it is necessary to activate the lock-out function to ensure protec-
tion from accidental switching on.
It is forbidden to charge the battery inside the flashlight when the
ambient temperature is below 0 °C.
1. Always follow the instructions from this manual and recommenda-
tions on battery usage.
2. Apply only the recommended power sources.
3. Do not reverse battery polarity.
4. Do not modify or recast the flashlight and its components as it will
deprive you of the warranty.
5. Do not allow water or any other liquid to leak into the flashlight.
6. Do not aim a switched-on flashlight at people's or animals' eyes — it
can cause temporary blindness.
7. Do not allow children to use the flashlight without your assistance.
The producer will not be liable for any harm done to the user if it
was caused by improper use of the product.

Care and Storage

It is recommended to clean the threads and O-rings off dirt and old
grease once or twice per year. Remember that reliable protection from
water and dust cannot be provided by worn-out sealing. The fouling as
well as lack of grease cause fast wear-out of the threads and sealing
rings.
4 ENG USER MANUAL WIZARD C2 WG
To clean the threads do the following:
1. Unscrew the tailcap and remove the sealing rings carefully with a
toothpick (do not use sharp metal objects as they can damage the
rings).
2. Wipe the sealing rings thoroughly with a soft cloth (or tissue). Do not
use solvents. If the sealing ring is worn out or damaged, replace it
with a new one.
3. Clean the metal threads with a brush using ethanol. Be careful not to
allow the applied liquid inside the flashlight, as it can cause malfunc-
tioning of the flashlight.
After cleaning, grease the threads and the sealing rings that have
been installed in place with polyalphaolefin-based silica grease, e.g.
Nyogel 760G. The application of other types of grease is unacceptable.
In case of active operation and exploitation in dusty environments, it is
recommended to clean and grease the parts as often as the necessity
arises.
WE DO NOT RECOMMEND leaving power supplies (especially
non-rechargeable) inside the flashlight for a long storage period, as
they can leak for various reasons and damage the inner parts of the
flashlight. If you want to keep your flashlight in a stand-by state with
batteries in, previously install new and high-quality batteries, store
the flashlight in acceptable for batteries operational temperature and
revise the batteries' state at least once a month. If you have noticed any
signs of defects, withdraw the batteries from the flashlight and dispose
of them.

Warranty and Service

Armytek provides free warranty repairs for 10 years (excluding
batteries, chargers, mounts, holders, switches and connectors, which
have 2-year warranty) from the date of purchase if there is a document
confirming the purchase.
The warranty does not apply to magnets, silicone covers of connectors
and buttons, silicone installation rings and holders, clips, silicone grips,
holsters, lanyards, O-rings and pads, Velcro tapes. The warranty also
does not extend to damage during:
1. Improper usage.
2. Attempts to modify or repair the flashlight by nonqualified
specialists.
3. Application in chlorinated, contaminated liquids or sea water.
4. Immersion into liquids in case of broken leakproofness.
5. Exposure to high temperatures and chemicals, including the liquids
from defected batteries.
6. Usage of low-quality batteries.
REV_00-0000