Unitech UT-40X Instruction Manual
  1. Manuals
  2. Brands
  3. Unitech Manuals
  4. Controller
  5. UT-40X
  6. Instruction manual

Unitech UT-40X Instruction Manual

Manual loader
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
M
INSTRUCTION MANUAL
Model No. : UT-40X
MANUAL LOADER
www.unitechinstrument.com
COM
RL-1
RL-2
RL-3
RL-4
M
96 x 96
96 x 48
Flame Proof
@
www.utplindia.in
sales@utplindia.in
+91 7046223333 , 9427301436
www

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UT-40X and is the answer not in the manual?

Questions and answers

Related Manuals for Unitech UT-40X

Summary of Contents for Unitech UT-40X

  • Page 1 INSTRUCTION MANUAL Model No. : UT-40X MANUAL LOADER www.unitechinstrument.com RL-1 RL-2 RL-3 RL-4 96 x 96 96 x 48 Flame Proof www.utplindia.in sales@utplindia.in +91 7046223333 , 9427301436...
  • Page 2 12 / 24 VDC – a switch, fuse (1A, 125A) or a circuit breaker. The above items should be installed together with UT-40X for the products electrical protection. The switch, Fuse or circuit-breaker should be located close to the controller, within easy reach operator.

  • Page 3: Table Of Contents

    MANUAL LOADER UT-40X CONTENTS OVERVIEW ....................INTRODUCTION ..................NSTALLATION ........................................MOUNTING ....................EXTERNAL DIMENSION TECHNICAL SPECIFICATIONS ........................................WIRING DIAGRAM PROGRAMMING ..................................OPERATION INTERFACE ..............MODE ACCESS FLOW CHART OPERATIONAL MODES ................................CONFIGURATION MODE .................... SETUP MODE .................

  • Page 4: Overview

    UNITECH have developed a versatile and easy-to-use selection of manual station, Model NO: UT-40X, which produce an accurate, digitally controlled and scaled 4 to 20 mA or 0 to 10 VDC output. The digital value shown on the controller display is same or proportional to the scaled output and is adjusted directly through the front panel push buttons to ensure precise and repeatable operation.

  • Page 5: Technical Specifications

    MANUAL LOADER UT-40X Technical Specifications FEATURES Input Impedance 150 Ohms. 4 - 20 Or 0 - 10 VDC PROCESS output. Full range Or step fecility. 4 Digit 12.5 MM Size LCD DISPLAY. Range/Decimal Point selectable through jumpers. 230V/100VAC or 24VDC Powered Supply.

  • Page 6: Wiring Diagram

    MANUAL LOADER UT-40X Wiring Diagram [A] 96 X 48 UT-40X 96X48 OUTPUT SUPPLY 4~20mA / 0~10VDC 230VAC / 12-24VDC Noise AC 230V, 50Hz POWER Filter [B] 96 X 96 4~20mA / 0~10VDC UT-40X OUTPUT 96X96 SUPPLY 230VAC / 12-24VDC AC 230V, 50Hz...

  • Page 7: Programming

    MANUAL LOADER UT-40X PROGRAMMING Operation Interface www.utplindia.in RL-4 RL-1 RL-2 RL-3 UT-40X FRONT VIEW NORMAL VIEWS 1. 7 segment Display 4 Digit 7 segment dedicated to display the present Output value. In Programing mode it shows Parameter and its value.

  • Page 8: Mode Access Flow Chart

    UNIVERSAL PROCESS INDICATOR & CONTROLLER UT-102 Mode Access Flow Chart. Setup Configuration Change Calibration Normal Mode Mode Mode Mode Password Mode Mode Selection Press key to enter into the Programming mode from Normal mode Any New Password NOTE : Default Password will be Protected Parameter Password will be These are the whole parameter list.

  • Page 9: Operational Modes

    MANUAL LOADER UT-40X OPERATIONAL MODES Configuration Mode ‘Configuration Mode’ will shown by pressing key, will be display and then by pressing Range / Values Display Parameter CONFIGURATION MODE Range : Values between Password for Config. Mode Parameters Scroll the digit by key, Increase by key.

  • Page 10: Setup Mode

    MANUAL LOADER UT-40X Setup Mode ‘Setup Mode’ Mode will shown by pressing key, after Mode display. Range / Values Display Parameter SETUP MODE Range : Values between Password for Setup Mode Parameters Scroll the digit by key, Increase by key.

  • Page 11: Calibration Mode

    MANUAL LOADER UT-40X Calibration Mode ‘Calibration Mode’ Mode will shown by pressing key, after Mode display. Range / Values Display Parameter CALIBRATION MODE Range : Values between Password for Calibration Mode Parameters Scroll the digit by key, Increase by key.

  • Page 12: Change Password Mode

    MANUAL LOADER UT-40X Change Password Mode ‘Change Password Mode’ Mode will shown by pressing key, after Mode display. Range / Values Display Parameter CHANGE PASSWORD MODE Range : Values between Password for Change Password Mode. Scroll the digit by key, Increase by key.

Table of Contents