Unitech UT-101 F Operation Manual
  1. Manuals
  2. Brands
  3. Unitech Manuals
  4. Controller
  5. UT-101 F
  6. Operation manual

Unitech UT-101 F Operation Manual

Universal process indicator / controller
Hide thumbs

Advertisement

Table of Contents

Model No. : UT-101 F
z
z
OPERATION MANUAL
UNIVERSAL PROCESS INDICATOR / CONTROLLER
Model No. : UT-101 F
"Sure for service with hi-end
Uni
versal
Tech
nology"
Add.-503/504,Helix Complex , Opp. Surya Hotel, Sayajigunj, Vadodra-05. Gujrat. INDIA, PH-0265 6623551
+91 94273 01436
Website:
www.unitechinstrument.com
Sales:
Email :
Sales@unitechinstrument.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UT-101 F and is the answer not in the manual?

Questions and answers

Related Manuals for Unitech UT-101 F

Summary of Contents for Unitech UT-101 F

  • Page 1 Model No. : UT-101 F OPERATION MANUAL UNIVERSAL PROCESS INDICATOR / CONTROLLER Model No. : UT-101 F “Sure for service with hi-end versal Tech nology” Add.-503/504,Helix Complex , Opp. Surya Hotel, Sayajigunj, Vadodra-05. Gujrat. INDIA, PH-0265 6623551 +91 94273 01436 Website: www.unitechinstrument.com...
  • Page 2 REGISTER ADDRESS FOR MODBUS CALIBRATION VALUES INTRODUCTION Unitech Instrument’s Universal Indicator is designed to accept thermo-couple or RTD or Linear Input and displays the process parameter through a 4 Digit Red LED Display. The instrument is available in a panel mounted housing which requires a cut out as per Panel cutout Dimensions given later .

  • Page 3: Front Panel Description

    Model No. : UT-101 F PAGE : 1 FRONT PANEL DESCRIPTION AL-1 AL-2 COM. UT-101 F-F UT-101 F-F DISPLAY DESCRIPTION Seven Segment LED display Actual Process Value Red LED will glow on Relay 1 activation. (If Applicable) Red LED will glow on Relay 2 activation. (If Applicable) Red LED will blink when there is communication.

  • Page 4: Technical Specification

    Model No. : UT-101 F PAGE : 2 TECHNICAL SPECIFICATION INPUT TYPE RANGE TYPE RANGE K-Type T/C -50 to 1200 ºC 4 to 20mA -1999 to 9999 J-Type T/C -50 to 750 ºC 0 to 20mA -1999 to 9999 R-Type T/C 0 to 1750 ºC...

  • Page 5: Installation

    Model No. : UT-101 F PAGE : 3 INSTALLATION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 C B A +V +TPS -TPS D+ D- NC1 C1 NO1 +OP -OP T/C+ T/C-...

  • Page 6: Programming Flow Chart

    Model No. : UT-101 F PAGE : 4 PROGRAMMING FLOW CHART Configuration Setup Calibration Change Mode Selection Mode Mode Mode Password Mode PRESS Any New Password NOTE : Default Password will be Protected Parameter Password will be “Sure for service with hi-end...

  • Page 7: Configuration Mode

    Model No. : UT-101 F PAGE : 5 CONFIGURATION MODE This Mode is used to change Input , Relay and Communication Operation Configuration CONFIGURATION MODE PARAMETER Description Range Parameter Default Value Password for Parameter Setting Scroll the digit by key, increase by key.

  • Page 8: Setup Mode

    Model No. : UT-101 F PAGE : 6 Description Range Parameter Default Value Parity : Even Parity : Odd Parity Change the type by key. : None Parity check for Communication Display Calculation : Linear Type Note : Factory set value Offset Factory set Value.

  • Page 9: Calibration Mode

    Model No. : UT-101 F PAGE : 7 Description Range Parameter Default Value Hysteresis # 2 000.2 000.0 999.9 Values from Increase digit by key, decrease by Offset to Process Value. 000.0 000.0 999.9 Values from Scroll the digit by key, increase by key.

  • Page 10: Error Message And Troubleshooting

    Model No. : UT-101 F PAGE : 8 PASSWORD PROTECTED PARAMETER Range Description Parameter Default Value Calibration Output Low. ---- According to output. Set the output by key, Press to fix the desired output. Calibration Output High. ---- According to Output.

  • Page 11: Calibration Values

    Model No. : UT-101 F PAGE : 9 REGISTER ADDRESS FOR MODBUS RTU PROTOCOL SR NO ANALOG PARAMETERS ABSOLUTE ADDRES ACCESS TYPE PROCESS VALUE 40001 READ ONLY DECIMAL POINT 40002 READ ONLY SETPOINT - 1 40003 READ/WRITE SETPOINT - 2...
  • Page 12 Total solution provider for Industrials Automaton PLC and HMI and hi speed communications module. SCADA system (standard and customized computer software) Servo Motors & Drives & AC drives / inverter Unitech Instruments 503/504 Helix Complex.Opp-Surya Hotel,Sayajigunj, Vadodra-390005,Gujarat ,India ax.: Phone.: 0265-6623551/6553555/2361241 265-6623551 E-mail :salse@unitechinstrument.com,kuntal_unitech@yahoo.com...

Table of Contents