Etekcity Lasergrip 630 Infrared Thermometer Manual

This easy-to-use device lets you conveniently and accurately measure surface temperatures from a distance without the need of any direct contact. Should you have any questions or concerns, feel free to contact our helpful customer support team toll-free at 855.686.3835 or by email at support@etekcity.com.

Package Contents

1 x Etekcity Lasergrip 630 Infrared Thermometer
1 x 9V DC Battery
1 x User Manual

Features & Specifications

• Laser guided targeting for aiming precision
• Dual laser guidance for enhanced aiming precision
• Narrow distance-spot ratio for accurate results at greater distances
• Safely measure hazardous or inaccessible objects
• Standard 9V battery powers up to 14 hours of cumulative use
• Auto-off after 15 seconds of inactivity
• Calculate max, min, average, and difference between temperature measurements

Function Diagram

1. LCD Display
2. Display Backlight / Laser Pointers/ (HOLD) Unit (ºC/ºF)
3. Mode Selection
4. UP / DOWN
5. Battery Compartment
6. Measurement Trigger
7. Laser Hole
8. IR Sensor

Display Icon Key

1. Hold temperature results
2. Laser guidance activated
3. Low battery power
4. Current / Last temperature reading
5. Secondary measurement (Mode)

Operation

Surface Temperature Measurement
NOTE: The Lasergrip cannot measure the temperature of objects behind glass. Inaccuracy may also occur when exposed to steam, dust or any other contaminants in the air.

1. Once the battery is properly installed, press the measurement trigger to activate the device.
2. Point the Lasergrip towards the surface of measurement.
3. Press and hold the measurement trigger and the lasers will activate for aiming guidance.
4. Keep holding the trigger as you move the Lasergrip if you wish to live scan the surface area for temperature measurement.

5. The area between each laser point is the area of measurement. Once the lasers are pointed to the desired area of measurement, release the trigger and the LCD display will lock the calculated temperature.
6. Press the measurement trigger once again to make another measurement.

NOTE: The Lasergrip LCD will display 'HI' when the measured temperature is above the measurable range, and will display '1.0' when the measured temperature is below the measurable range.

Unit Conversion
To switch the unit of measurement between ºF and ºc, press and hold the display backlight button for 3 seconds.

Laser Activation & Display Backlight Operation
To activate and deactivate the laser and display backlight, press the backlight button repeatedly to cycle through the following modes: both off, backlight on with laser off, backlight off with laser on, and both on.

Measurement Modes

Press the mode button repeatedly to cycle through and select from the following measurement modes:

NOTE: To adjust the value in EMS, HAL, and LAL mode, use the UP and DOWN buttons on the thermometer.

Battery Replacement

A low battery icon will appear on the LCD display when the Lasergrip's battery power is running low. Immediately replace the battery when the icon appears.

1. Open the battery compartment and remove the used battery. Dispose the used battery properly.

2. Connect a new DC 9V battery, making sure it's under the correct polarity.
3. Insert the battery into the compartment and close the compartment lid, making sure the wiring is not being pinched by the compartment lid.

Distance-Spot Ratio

The Lasergrip 630 measures surface temperature on the basis of distance to spot diameter ratio (D:S). As the distance between the thermometer and the surface increases, the total surface area measured will also increase. With a distance to spot ratio of 16:1 the surface area measured has a diameter of roughly 1/16 the distance. For the most accurate results, stand at a distance where the two laser points overlap (approximately 14 inches away from the spot of measurement). Otherwise, the space between each laser point marks the diameter for the area of measurement.

Emissivity
The emissivity of a material is its efficiency in emitting thermal energy. Non-reflective surfaces have a higher emissivity (closer to 1) than reflective surfaces (closer to 0). Inaccurate results may occur when measuring reflective surfaces such as glass, polished wood, and garnite. To take accurate temperature measurement of reflective surfaces with low emissivity, adjust the emissivity value before measurement using the reference chart. Or, place a strip of masking tape over the surface and allow for it to adjust to the temperature of the surface for approximately 30 minutes. Measure the surface, scanning the taped section, eliminating the issue of inaccuracy.

• DO NOT point the laser-light at another person or animal.
• DO NOT attempt to point laser-light at an aircraft.
• Avoid direct/indirect eye contact with the laser-beam. Laser radiation may cause eye damage.
• DO NOT view the beam with optical instruments. In the vicinity of use, make any bystanders aware of the dangers of looking directly into the laser beam.
• DO NOT allow children to operate the device. Use a 9V battery when replacing the battery within the device. Make sure to insert the battery in accordance with the correct polarities.
• ALWAYS remove the batteries when cleaning the device.
• DO NOT use leaking batteries or dispose old batteries in fire. Remove battery for storage if the device is not being used for a prolonged period of time.
• DO NOT disassemble the device or tamper with internal components. Doing so will void any warranty.
• DO NOT touch the lens or wipe it using anything other than a soft cloth or cotton swab. Keep the thermometer away from electromagnetic fields produced by objects such as arc welders and induction heaters.
• DO NOT expose the thermometer to direct sources of heat for extended periods of time.
• The thermometer measures surface temperature, not internal temperature. Do not use the Lasergrip as a reliable source to measure body temperatures.

Questions or Concerns?
Please contact us Mon-Fri 9:00 AM - 6:00 PM PST at (855) 686-3835 or email support@etekcity.com
visit www.etekcity.com for more products.