Wavetek 2001 Instruction Manual page 9

M o d e l
2001
SECTION
2
INSTALLATION
2.1 MECHANICAL INSTALLATION
2.1 . I Initial Inspection
After unpacking the instrument, visually inspect the
external parts for damage to knobs, connectors, surface
areas, etc. The shipping container and packing material
should be saved in case it is necessary to reship the unit.
2.1.2 Damage Claims
If the instrument is received mechanically damaged in
transit, notify the carrier and either the nearest Wavetek
area representative or the factory in Indiana. Retain the
shipping carton and packing material for the carrier's
inspection.
The local representative, or the factory, will immediately
arrange for either the replacement or repair of your in-
strument, without waiting for damage claim settlements.
2.1.3 Rack Mounting
The instrument is 1 /2 racksize and t w o rack mounting
kits are available. The K-103 kit provides the necessary
hardware to mount the unit to either tlie right or left of
a standard 5%" x 19" opening. The K- 104 kit provides
the necessary hardware to rack mount t w o instruments.
These may be t w o 1000 or 2000 series Wavetek, Indi-
ana Instruments, or t w o 130 or 140 series Wavetek,
San Diego Instruments, or a combination of either. This
provides a
7"
x 19" package. Facilities are provided for
Front Panel mounting of instrument Rear Panel con-
nectors.
2.1.4 K-103, Rack Mounting Kit (Refer to Figure 2-1
)
CONTENTS
Item
Qty. Part No.
A (Side) 1 ea. 8000-608
B (Side) 1 ea. COOO-691
C (Screw)
8 ea. HS101-806
Procedure:
Remove the screws from one side panel at a time. Mount
item A or B against the side panel of the instrument and
secure with screws provided (item C). Repeat operation
for other side. NOTE: Items A & B may be interchanged
to position the unit to the side of the rack desired.
Figure 2-1. K-103 Rack Mounting
Model
2001
2.1 MECHANICAL INSTALLATION
2.1.1
I nitial Inspection
After unpacking the instrument, visually inspect the
external parts for damage to knobs, connectors, surface
areas, etc. The shipping container and packing material
should be saved in case it is necessary to reship the unit.
2.1.2
Damage Claims
If the instrument is received mechanically damaged in
transit, notify the carrier and either the nearest Wavetek
area representative or the factory in Indiana. Retain the
shipping carton and packing material for the carrier's
inspection.
The loca! representative, or the factory, will immediately
arrange for either the replacement or repair of your in-
strument, without waiting for damage claim settlements.
2.1.3
Rack Mounting
The instrument is 1/2 rack. size and two rack mounting
kits are available. The K-1 03 kit provides the necessary
hardware to mount the unit to either the right or left of
a standard 5;4" x 19" opening. The K·1 04 kit provides
A
.. --
..
- -
2
SECTION
INSTALLATION
the necessary hardware to rack mount two instruments.
These may be two 1000 or 2000 series Wavetek, Indi-
ana Instruments, or two
130
or 140 series Wavetek,
San Diego Instruments, or a combination of either. This
provides a 7" x 19" package. Facilities are provided for
Front Panel mounting of instrument Rear Panel con-
nectors.
2.1.4 K-103, Rack Mounting Kit (Refer to Figure 2-1)
CONTENTS
Item Qty. Part No.
A
(Side) 1 ea. BOOO-608
B (Side) 1 ea.
COOO-691
C (Screw) 8 ea. HS1 01 -806
Procedure:
Remove the screws from one side panel at a time. Mount
item A or B against the side panel of the instrument and
secure with screws provided (item C). Repeat operation
for other side. NOTE: Items A & B may be interchanged
to position the unit to the side of the rack desired.
B
- l"
--
...
Figure 2-1. K-103 Rack Mounting
2-1