Table of Contents
Advertisement
GENERAL INFORMATION
TABLE 1-1.
Specifications (Con't.)
Model
2001
External Market Input -
Front Panel BNC connector accepts external CW signal
for conversion to a Birdy marker.
Input level:
100 m V
into 50 ohms
Marker Width
-
Adjustable from (approx.) 15 to 400 kHz in four steps
Marker Size
Large
-
Adjustable from (approx.) 12 V to 15 m V peak-to-peak
Small
-
Adjustable from (approx.) 50 m V to 100 uV peak-to-peak
Rectified Birdy
(for use with X-Y plotters) -
Size varies with detector's impedance.
Adjustable from
(approx.) 6 V to 1 m V with detector impedance of 1 meg
ohm, or from 0.5V to 1 mV with detector impedance of
0 ohms.
Rectified birdy is positive polarity
Marker T i l t -
Provides horizontal markers have a size equal to approxi-
mately 10% of horizontal display. Adjustment of marker
size vectorily adds the normal vertical marker t o the
horizontal marker, causing the resulting marker t o vary
from a horizontal position toward a vertical position.
POWER REQUIREMENTS
Line Supply
115 or 230 VAC *lo%, 50 to 60 Hz, (approx 20 watts)
MECHANICAL SPECIFICATIONS (See Figure 1-1.)
A For total length, including knobs,
add 11/16 inch
I3 For total height, including feet,
add 518 inch
C For total width, including screw
heads, add 3/16 inch
Weight
Net
-
19 Ibs.
Shipping -
25 Ibs.
Figure 1-1.
1.3 OPTIONS
1.3.1
Marker A-1. Any single frequency between 1 t o 1400 MHz.
1.3.2
Marker A-2. Harmonic type at 1, 10 or 50 MHz. (Other frequencies available on special order.)
1.3.3
Modulator A-4. Provides 100% amplitude modulation at a 1 kHz rate.
1.3.4
Perllift A-5. Provides contact closure during sweep time.
GENERAL INFORMATION
Model 2001
1.3
TABLE
1-1. Specifications (Con't.)
External Market Input -
Marker Width -
Marker Size
Large -
Small -
Rectified Birdy
(for use with X-V plotters) -
Marker Tilt -
POWER REQUIREMENTS
Line Supply
Front Panel BNC connector accepts external CW signal
for conversion to a Birdy marker.
Input level:
100 mV
into 50 ohms
Adjustable from (approx.) 15 to 400 kHz in four steps
Adjustable from (approx.) 12 V to 15 m V peak·to·peak
Adjustable from (approx.) 50 mV to 100 uV peak·to·peak
Size varies with detector's impedance.
Adjustable from
(approx.) 6 V to 1 mV with detector impedance of 1 meg
ohm, or from 0.5V to 1 mV with detector impedance of
o
ohms.
Rectified birdy is positive polarity
Provides horizontal markers have a size equal to approxi-
mately 10010 of horizontal display. Adjustment of marker
size vectorily adds the normal vertical marker to the
horizontal marker, causing the resulting marker to vary
from a horizontal position toward a vertical position.
115 or 230 VAC
±
10010, 50 to 60 Hz, (approx 20 watts)
MECHANICAL SPECIFICATIONS (See Figure 1-1.)
A For total length, including knobs,
I
[
add 11/16 inch
B
For total height, including feet,
TOP
add 5/8 inch
C For total width, including screw
A~I
..
13
.. I
heads, add 3/16 inch
K[
1
G
Weight
SIDE
Net -
191bs.
Shipping -
251bs.
Ls
C~~8~~t-C
Figure 1-1.
OPTIONS
1.3.1
Marker A-1. Any single frequency between 1 to 1400 MHz.
1.3.2
Marker A-2. Harmonic type at 1, 10 or 50 MHz. (Other frequencies available on special order.)
1.3.3
Modulator A-4. Provides 100% amplitude modulation at a 1 kHz rate.
1.3.4
Perilift A-5. Provides contact closure during sweep time.
1-4
Advertisement
Table of Contents
