Table of Contents
Advertisement
GENERAL INFORMATION
TABLE 1-1. Specifications (Con't.)
Model
2001
Frequency Dial
Calibration
-
Accuracy -
10
MHz intervals
Band
1
10
MHz
Band
2
2%
of selected frequency
Band 3
2%
of selected frequency
Sweep Width -
200
kHz to
500
MHz-calibrated in
10
MHz intervals
Accuracy -
Band 1
f 10
MHz
Band
2
f20
MHz
Band 3
k20
MHz
Display Linearity
-
2%
Spurious Signals -
Band 1
10
to
500
MHz 26dB below output
Band
2
500
to
950
MHz, 26dB below output
Band 3
900
to
1400
MHz, 26dB below output
Residual FM -
Less than 15kHz
Drift
-
Blanking
-
RF Output Amplitude
-
Flatness at
+10
dBm -
100
kHz15 minutes
-
2
MHz18 hours
(after
112
hourwarm-up at a constant ambient, and allowing
a
5
minute stabilizing period after
a
frequency change)
Retrace blanking of the RF output provided for sweep
operation.
Removed for CW operation.
Continuously adjustable from
+10
t o -80 dBm;
70
dB in
10
dB steps, plus a
20
dB vernier, calibrated in
1
dB
increments.
Step attenuator and vernier attenuator ac-
curacy :
k0.5
dB t o
500
MHz
k1
dB to
1000
MHz
f 2
dB t o
1400
MHz
f0.5
dB over
1
t o
1400
MHz (when read with negative
detector)
f0.75
dB over
1
to
1400
MHz (when read with a power
meter)
Impedance -
50
ohms
REMOTE PROGRAMMING
A Rear Panel REMOTE Jack provides necessary connections for Remote Control of frequency, sweep
width and the
0
t o
20
dB vernier output control. This jack also provides connections for EXTERNAL
amplitude and frequency modulation.
Frequency -
May be remotely programmed within the selected band by
a
k16
V signal. (-16 volts corresponds to LOW frequency
GENERAL INFORMATION
Model 2001
1-2
Frequency Dial
Calibration -
Accuracy -
Sweep IJlJidth -
Accuracy -
Display Linearity -
Spurious Signals -
Residual FM -
Drift -
Blanking -
RF Output Amplitude -
Flatness at +10 dBm -
Impedance -
REMOTE PROGRAMMING
TABLE 1-1. Specifications (Con't.)
10 MHz intervals
Band 1
Band 2
Band 3
10 MHz
2% of selected frequency
2% of selected frequency
200 kHz to 500 MHz-calibrated in
10 MHz intervals
Band 1
Band 2
Band
3
2%
Band 1
Band 2
Band
3
±10 MHz
±20 MHz
±20 MHz
10 to 500 MHz 26dB below output
500 to 950 MHz, 26dB below output
900 to 1400 MHz, 26dB below output
less than 15kHz
100 kHz/5 minutes - 2 MHz/8 hours
(after 1/2 hour warm-up at a constant ambient, and allowing
a 5 minute stabilizing period after a frequency change)
Retrace blanking of the RF output provided for sweep
operation.
Removed for CW operation.
Continuously adjustable from +10 to -80 dBm; 70 dB in
10
dB steps, plus a 20 dB vernier, calibrated in 1 dB
increments.
Step attenuator and vern ier attenuator ac-
curacy:
±0.5 dB to 500 MHz
± 1 dB to 1000 MHz
±2 dB to 1400 MHz
±0.5 dB over 1 to 1400 MHz (when read with negative
detector)
±0.75 dB over 1 to 1400 MHz (when read with a power
meter)
50 ohms
A Rear Panel REMOTE Jack provides necessary connections for Remote Control of frequency, sweep
width and the 0 to 20 dB vernier output control. This jack also provides connections for EXTERNAL
amplitude and frequency modulation.
Frequency -
May be remotely programmed within the selected band by
a
±
16
V
signal. (-16 volts corresponds to LOW frequency
Advertisement
Table of Contents
