Panasonic TOUGHBOOK CF-M34 Series Operating Instructions Manual page 25

13
At the confirmation message , press
CD.
The computer will reboot, and the operations of reinstal¬
lation for the hard disk start automatically. (The opera¬
tions take about 15 minutes.)
When "Insert media 2" is displayed, insert Product Re¬
covery CD-ROM 2, or when "Insert media 3" is displayed,
insert Product Recovery CD-ROM 3 into the CD drive
and immediately select [OK],
(In the case of Windows NT, only Product Recovery CD-
ROMs 1 and 2 can be used.)
\
NOTE J-
If [OK] is not immediately selected:
The message "The media does not contain the correct
file" may appear. In such cases, the message "Insert
media 2..." is displayed again when [OK] is selected.
Confirm that Product Recovery CD-ROM 2 has been
inserted by opening the tray of the CD drive, then close
the tray and immediately select [OK].
14
After the reinstallation procedure completes, press
C
Enter
). The computer will be shut down.
15
<On!y when using the CD-ROM drive Panasonic KXL-
RYVI0A>
Remove the FIRSTAID FD.
16
Remove the CD-ROM drive, and then turn the computer
on.
17
When the message [Press <F2> to enter SETUP] is dis¬
played, press (
F2
) and then run the Setup Utility.
If the password has been set, enter the Supervisor Pass¬
word. _
18
Press (
F9
).
At the confirmation message, select [Yes] and press
(
Enter
). (The Setup Utility settings will return to their
default values. Even the security settings with the excep¬
tion of the password(s) will return to their default values.)
Change the settings where necessary.
19
Press (
F10
)
.
At the confirmation message, select [Yes] and press
( Enter ).
20
Perform the setup procedure for Windows by following
the instructions on the screen, (jy3 page 11
Ynote)-
When an UPDATE FD is to be created, follow the steps
in the readme.txt on the disk. (Q= page 13)
<When using a PC Card-compatible CD-ROM drive
other than the Panasonic KXL-RW10A>
Copy the necessary drivers, from the floppy disk included
with your CD-ROM drive, to the FIRSTAID FD with the
method below. It will be necessary to edit the
CONFIG.SYS file and AUTOEXEC.BAT file on the
FIRSTAID FD. When editing the AUTOEXEC.BAT file.
Some CD-ROM drives require card managers (card and
socket service). See the manual included with your CD-
ROM drive for further details.
(T) Start Windows and insert the FIRSTAID FD.
(2) Select [Start]-[Programs]-[Accessories]-[NotePad] and
open [a:\config.sys].
(3) Rewrite the following line and save.
Delete the following four lines.
;KXL-RW10A DRIVER
DEVICE=A:\TOOLS\KMASMGRA.SYS
DEVICE=A:\TOOLS\KMASASPA.SYS
DEVICE=A:\TOOLS\KMASCDA.SYS /D:MSCD000
Add the driver of your CD-ROM drive.
Device=A:\DRIVER1 ,SYS /DiMSCDOOO
Rewrite this driver for the driver of your
CD-ROM drive. The driver for the PC
Card will also be necessary. Refer to the
operation manual that accompanies the
CD-ROM drive.
(4) Copy the CD-ROM driver file (i.e., the driver file re¬
written in step (3)) of the CD-ROM drive below [a:\]
of the FIRSTAID FD.
(5) Set the floppy disk to the write-protect state.
After this, follow the reinstalling procedure of <when us¬
ing the CD-ROM drive Panasonic KXL-R\V10A>.
(Q" page 24)
25