Page 1
G&D Computer and Console Modules Installation and Operation Standard variants A9200136-2.41...
Page 2
About this manual This manual has been carefully compiled and examined to the state-of-the-art. G&D neither explicitly nor implicitly takes guarantee or responsibility for the qual- ity, efficiency and marketability of the product when used for a certain purpose that differs from the scope of service covered by this manual.
Page 3
FCC Statement The devices named in this manual comply with Part 15 of the FCC Rules. Opera- tion is subject to the following two conditions: (1) the devices may not cause harm- ful interference, and (2) the devices must accept any interference received, including interference that may cause undesired operation.
Safety guidelines Safety guidelines Please read through the following safety guidelines before putting the G&D product into operation. The guidelines help to avoid damage to the product and prevent potential injuries. Keep these safety guidelines ready to hand for all persons who use this product. Observe all warnings and operating information given at the device or in this operat- ing manual.
Page 7
Safety guidelines Ensure correct installation position for devices with ventilation openings For reasons of electric safety, devices with ventilation openings must only be installed in an upright, horizontal position. Do not insert any objects through the device’s openings Objects should never be inserted through the device’s openings. Dangerous voltage could be present.
Page 8
Safety guidelines Special advices for dealing with laser technology devices of the computer modules and console modules use components Fiber with laser technology which comply with laser class 1 or better. They meet the requirements according to EN 60825-1:2014 as well as U.S.
Computer modules Computer module »DVI-CPU« With computer modules, you can connect a computer with graphics out- DVI-CPU put to a digital matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. Users at the consoles of the matrix switch can access the computer module and oper- ate the connected computer.
Page 10
Computer module »DVI-CPU« Installation Connecting computers Keyb. Mouse USB K/M DVI-D CPU NOTE: Both keyboard and mouse signals can be transmitted to the computer using the PS/2 or the USB ports. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the purple PS/2 socket (keyboard) to this port.
Page 11
Computer module »DVI-CPU« Power supply Power In: Plug the power cable of the power pack in this interface. Then connect the power cable to the power pack and a power outlet. Status displays The LED on the back panel of the computer module shows the status of the external...
Page 12
Computer module »DVI-CPU« Technical data DVI-CPU Interfaces to Video: 1 × DVI-D (Single Link) computer: Keyboard and mouse signals: 2 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack socket Data transmission Interface: 1 × RJ45 socket...
Computer module »DVI-CPU-UC« Computer module »DVI-CPU-UC« With computer modules, you can connect a computer with graphics DVI-CPU-UC output to two different digital matrix switches of the ControlCenter-Compact or Control- Center-Digital series. Users at the consoles of the matrix switch can access the computer module and operate the connected computer.
Page 14
Computer module »DVI-CPU-UC« Installation Connecting the computer Keyb. Mouse USB K/M DVI-D CPU NOTE: Both keyboard and mouse signals can be transmitted to the computer using the PS/2 or the USB ports. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the purple PS/2 socket (keyboard) to this port.
Page 15
Computer module »DVI-CPU-UC« Connections to the matrix switches IMPORTANT: Only connect one Trans. interface of the computer module per matrix switch. NOTE: Use category 5e twisted pair cables (or better) to connect the devices. Connect this interface to a Dynamic Port (RJ45) of a matrix switch.
Page 16
Computer module »DVI-CPU-UC« Status displays The LED on the back panel of the computer module shows the status of the external power pack: Status Meaning Power Green The external power pack is connected and the required voltage (12 Volt) is available.
Page 17
Computer module »DVI-CPU-UC« Technical data DVI-CPU-UC Interfaces to Video: 1 × DVI-D (Single Link) computer: Keyboard and mouse signals: 2 × PS/2 socket 1 × USB-B Audio: 2 × 3.5 mm jack socket Data transmission Interface: 2 × RJ45 sockets...
Computer module »DVI-CPU-MC2« Computer module »DVI-CPU-MC2« With DVI-CPU-MC2 computer modules, you can connect a computer with two graphics outputs (dual-head) to a digital matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. Users at the consoles of the matrix switch can access the computer module and operate the connected computer.
Page 19
Computer module »DVI-CPU-MC2« Installation Connecting the computer DVI-D CPU 2 Keyb. Mouse USB K/M DVI-D CPU 1 NOTE: Keyboard and mouse signals can be transmitted to the computer using either the PS/2 interfaces or the USB interface. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the computer’s PS/2 keyboard interface to this interface.
Page 20
Computer module »DVI-CPU-MC2« Connection to the matrix switch NOTE: Only use category 5e (or better) twisted pair cables to connect the devices. Trans.|Channel 1: Connect this interface to a Dynamic Port (RJ45) of the matrix switch. Connect this interface to another Dynamic Port (RJ45) of the matrix Trans.|Channel 2:...
Page 21
Computer module »DVI-CPU-MC2« Status displays The LED on the back panel of the computer module shows the status of the external power pack: Status Meaning Power Green The external power pack is connected and the required voltage (12 Volt) is available.
Page 22
Computer module »DVI-CPU-MC2« Technical data DVI-CPU-MC2 Interfaces to Video: 2 × DVI-D (single link) computer Keyboard and mouse signals 2 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission to Interface: 2 × RJ45 socket...
Computer module »DVI-CPU-MC2-UC« Computer module »DVI-CPU-MC2-UC« With computer modules, you can connect a computer with two DVI-CPU-MC2 graphics outputs (dual-head) to two different digital matrix switches of the Control- Center-Compact or ControlCenter-Digital series. Users at the consoles of the matrix switch can access the computer module to operate the connected computer.
Page 24
Computer module »DVI-CPU-MC2-UC« Installation Connecting the computer DVI-D CPU 2 Keyb. Mouse USB K/M DVI-D CPU 1 NOTE: Keyboard and mouse signals can be transmitted to the computer using either the PS/2 interfaces or the USB interface. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the computer’s PS/2 keyboard interface to this interface.
Page 25
Computer module »DVI-CPU-MC2-UC« Connections to the matrix switches IMPORTANT: Connect only one of the computer module’s Trans. interfaces for each matrix switch! NOTE: Only use category 5e (or better) twisted pair cables to connect the devices. Connecting the first matrix switch Trans.
Page 26
Computer module »DVI-CPU-MC2-UC« Automatic grouping of channels When operating the computer module for the first time, the matrix switch recognises the main channel and the computer module’s additional channel. The channels are automatically added to a channel group. The web application uses the following icons to mark the different types of channels: computer module icon with »...
Page 27
Computer module »DVI-CPU-MC2-UC« Status displays The LED on the front panel of the computer module shows the status of the external power pack: Status Meaning Power The external power pack is connected and the required voltage (12 Volt) is available.
Page 28
Computer module »DVI-CPU-MC2-UC« Technical data DVI-CPU-MC2-UC Interfaces to Video: 2 × DVI-D (single link) computer Keyboard and mouse signals 2 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission to Interface: 4 × RJ45 socket...
Computer module »DVI-CPU-Fiber« Computer module »DVI-CPU-Fiber« With computer modules, you can connect a computer with graphics DVI-CPU-Fiber output to a digital matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. NOTE: This computer module can only be connected to a compatible fiber port of...
Page 30
Computer module »DVI-CPU-Fiber« Installation Connecting the computer Keyb. Mouse USB K/M DVI-D CPU NOTE: Keyboard and mouse signals can be transmitted to the computer using either the PS/2 interfaces or the USB interface. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the computer’s PS/2 keyboard interface to this interface.
Page 31
Computer module »DVI-CPU-Fiber« Connection to the matrix switch The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to as well as EN 60825-1:2014 U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 32
Computer module »DVI-CPU-Fiber« Status displays The LED on the back panel of the computer module shows the status of the external power pack: Status Meaning Power The external power pack is connected and the required voltage (12 Volt) is available.
Page 33
Computer module »DVI-CPU-Fiber« Technical data DVI-CPU-FIBER Interfaces to com- Video: 1 × DVI-D (single link) puter Keyboard and mouse signals 2 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission to Interface: 1 × LC-Duplex socket...
Page 34
Computer module »DVI-CPU-Fiber« DVI-CPU-FIBER Storage Temperature: -20 °C to +60 °C environment Air humidity: 15 % to 85 %, non-condensing Conformity CE, UKCA, FCC class B, TAA, EAC, RoHS, WEEE, REACH Computer and console modules · 29...
Computer module »DVI-CPU-Fiber-UC« Computer module »DVI-CPU-Fiber-UC« With computer modules, you can connect a computer with DVI-CPU-Fiber-UC graphics output to two different matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. NOTE: This computer module can be connected to a compatible fiber port of...
Page 36
Computer module »DVI-CPU-Fiber-UC« Installation Connecting the computer DVI-CPU-Fiber-UC Keyb. Mouse USB K/M DVI-D CPU NOTE: Keyboard and mouse signals can be transmitted to the computer using either the PS/2 interfaces or the USB interface. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the computer’s PS/2 keyboard interface to this interface.
Page 37
Computer module »DVI-CPU-Fiber-UC« Connection to the matrix switch The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to as well as EN 60825-1:2014 U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 38
Computer module »DVI-CPU-Fiber-UC« Status displays The LED on the back panel of the computer module shows the status of the external power pack: Status Meaning Power The external power pack is connected and the required voltage (12 Volt) is available.
Page 39
Computer module »DVI-CPU-Fiber-UC« Technical data DVI-CPU-FIBER-UC Interfaces to Video: 1 × DVI-D (single link) computer Keyboard and mouse signals 2 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission Interface: 2 × LC-Duplex socket...
Page 40
Computer module »DVI-CPU-Fiber-UC« DVI-CPU-FIBER-UC Storage Temperature: -20 °C to +60 °C environment Air humidity: 15 % to 85 %, non-condensing Conformity CE, UKCA, FCC class B, TAA, EAC, RoHS, WEEE, REACH Computer and console modules · 35...
Computer module »DL-DVI-CPU« Computer module »DL-DVI-CPU« With computer modules, you can connect a computer with graphics DL-DVI-CPU DL-DVI output to a digital matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. Users at the consoles of the matrix switch can access the computer module and operate the connected computer.
Page 42
Computer module »DL-DVI-CPU« Installation Connecting the computer Line In Line Out USB K/M Keyb. DL-DVI CPU DL-DVI CPU: Use the supplied video cable to connect the computer’s video output to this interface. Line In: Use one of the supplied audio cables to connect the computer’s Line Out interface to this interface.
Page 43
Computer module »DL-DVI-CPU« Start-up Connect the cable of the power pack to this interface. Now connect the power cable to the power pack and a power socket. Status displays The Power LED on the back panel of the computer module shows the status of the...
Page 44
Computer module »DL-DVI-CPU« Technical data DL-DVI-CPU Interfaces to Video: 1 × DVI-D (Dual Link) computer Keyboard and mouse signals 1 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission to Interface: 1 × RJ45 socket...
Page 45
Computer module »DL-DVI-CPU« DL-DVI-CPU Power supply Type: Portable power pack (12 V/2 A) Connector: 1 × Mini-DIN 4 socket Power input: 0.6A @ 12 VDC Housing Material: Anodised aluminium Dimensions (W × H × D): Approx. 105 × 26 × 164 mm Weight: Approx.
Computer module »DL-DVI-CPU-UC« Computer module »DL-DVI-CPU-UC« With DL-DVI-CPU-UC computer modules, you can connect a computer with DL-DVI graphics output to two different digital matrix switches of the ControlCenter-Compact or ControlCenter-Digital series. At the consoles of both matrix switches, users can access a computer module to operate the connected computer.
Page 47
Computer module »DL-DVI-CPU-UC« Installation Connecting the computer Line In Line Out Keyb. DL-DVI CPU USB K/M DL-DVI CPU: Use the supplied video cable to connect the computer’s video output to this interface. Use an audio cable to connect the computer’s Line-Out interface to this port.
Page 48
Computer module »DL-DVI-CPU-UC« Start-up Connect the cable of the power pack to this interface. Now connect the power cable to the power pack and a power socket. Status displays The Power LED on the back panel of the computer module shows the status of the...
Page 49
Computer module »DL-DVI-CPU-UC« Technical data DL-DVI-CPU-UC Interfaces to Video: 1 × DVI-D (Dual Link) computer: Keyboard and mouse signals: 1 × PS/2 socket 1 × USB-B Audio: 2 × 3.5 mm jack socket Data transmission Interface: 2 × RJ45 sockets...
Page 50
Computer module »DL-DVI-CPU-UC« DL-DVI-CPU-UC Power supply Type: Power pack (12 V/2 A) Connection: 1 × Mini-DIN 4 socket Current consumption: 0.6A @ 12 VDC Casing Material: Anodised aluminium Dimensions (W × H × D): Approx. 105 × 26 × 164 mm Weight: Approx.
Computer module »DL-DVI-CPU-Fiber« Computer module »DL-DVI-CPU-Fiber« With computer modules, you can connect a computer with DL-DVI-CPU-Fiber DL-DVI graphics output to a digital matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. NOTE: This computer module can be connected to a compatible fiber port of...
Page 52
Computer module »DL-DVI-CPU-Fiber« Installation Connecting the computer Line In Line Out USB K/M Keyb. DL-DVI CPU DL-DVI CPU: Use the supplied video cable to connect the computer’s video output to this interface. Line In: Use one of the supplied audio cables to connect the computer’s Line Out interface to this interface.
Page 53
Computer module »DL-DVI-CPU-Fiber« Connection to the matrix switch IMPORTANT: The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to as well as EN 60825-1:2014 U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 54
Computer module »DL-DVI-CPU-Fiber« Start-up Connect the cable of the power pack to this interface. Now connect the power cable to the power pack and a power socket. Status displays The Power LED on the back panel of the computer module shows the status of the...
Page 55
Computer module »DL-DVI-CPU-Fiber« Technical data DL-DVI-CPU-FIBER Interfaces to Video: 1 × DVI-D (Dual Link) computer Keyboard and mouse signals 1 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission to Interface: 1 × LC-Duplex socket...
Page 56
Computer module »DL-DVI-CPU-Fiber« DL-DVI-CPU-FIBER Power supply Type: Portable power pack (12 V/2 A) Connector: 1 × Mini-DIN 4 socket Power input: 0.6A @ 12 VDC Housing Material: Anodised aluminium Dimensions (W × H × D): Approx. 105 × 26 × 164 mm Weight: Approx.
Computer module »DL-DVI-CPU-Fiber-UC« Computer module »DL-DVI-CPU-Fiber-UC« With DL-DVI-CPU-Fiber-UC computer modules, you can connect a computer with DL-DVI graphics output to two different digital matrix switches of the ControlCenter-Compact or ControlCenter-Digital series. NOTE: This computer module can be connected to a compatible fiber port of...
Page 58
Computer module »DL-DVI-CPU-Fiber-UC« Installation Connecting the computer Line In Line Out USB K/M Keyb. DL-DVI CPU DL-DVI CPU: Use the supplied video cable to connect the computer’s video output to this interface. Line In: Use one of the supplied audio cables to connect the computer’s Line Out interface to this interface.
Page 59
Computer module »DL-DVI-CPU-Fiber-UC« Connection to the matrix switch The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to as well as EN 60825-1:2014 U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 60
Computer module »DL-DVI-CPU-Fiber-UC« Start-up Connect the cable of the power pack to this interface. Now connect the power cable to the power pack and a power socket. Status displays The Power LED on the back panel of the computer module shows the status of the...
Page 61
Computer module »DL-DVI-CPU-Fiber-UC« Technical data DL-DVI-CPU-FIBER-UC Interfaces to Video: 1 × DVI-D (Dual Link) computer Keyboard and mouse signals 1 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission to Interface: 2 × LC-Duplex socket...
Page 62
Computer module »DL-DVI-CPU-Fiber-UC« DL-DVI-CPU-FIBER-UC Power supply Type: Portable power pack (12 V/2 A) Connector: 1 × Mini-DIN 4 socket Power input: 0.6A @ 12 VDC Housing Material: Anodised aluminium Dimensions (W × H × D): Approx. 105 × 26 × 164 mm Weight: Approx.
Computer module »DP-CPU« Computer module »DP-CPU« With computer modules, you can connect a computer with graphics DP-CPU DisplayPort output to a digital matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. The module uses the VESA DisplayPort DualMode standard 1.1. IMPORTANT: For correct operation, the computer also needs to support the DualMode standard (often marked with DP++).
Page 64
Computer module »DP-CPU« Installation Connecting the computer Keyb. Mouse USB K/M DP ++ CPU NOTE: Keyboard and mouse signals can be transmitted to the computer using either the PS/2 interfaces or the USB interface. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the computer’s PS/2 keyboard interface to this interface.
Page 65
Computer module »DP-CPU« Status displays The LED on the back panel of the computer module shows the status of the external power pack: Status Meaning Power The external power pack is connected and the required voltage (12 Volt) is available. The external power pack is not (properly) connected.
Page 66
Computer module »DP-CPU« Technical data DP-CPU Interfaces to com- Video: 1 × Display-Port puter (DualMode standard 1.1) Keyboard and mouse signals 2 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission to Interface: 1 × RJ45 socket the counterpart Transmission distance: Max.
Computer module »DP-CPU-UC« Computer module »DP-CPU-UC« With computer modules, you can connect computers with DP-CPU-UC DisplayPort graphics output to two different matrix switches of the ControlCenter-Compact or ControlCenter-Digital series. The module uses the VESA DisplayPort DualMode standard 1.1. IMPORTANT: For correct operation, the computer also needs to support the DualMode standard (often marked with DP++).
Page 68
Computer module »DP-CPU-UC« Installation Connecting the computer Keyb. Mouse USB K/M DP ++ CPU NOTE: Keyboard and mouse signals can be transmitted to the computer using either the PS/2 interfaces or the USB interface. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the computer’s PS/2 keyboard interface to this interface.
Page 69
Computer module »DP-CPU-UC« Trans. 1: Connect this interface to a Dynamic Port (RJ45) of the first matrix switch. Connect this interface to a Dynamic Port (RJ45) of the second matrix switch. Trans. 2: ADVICE: You can also connect the computer module directly to up to two compatible console modules.
Page 70
Computer module »DP-CPU-UC« Technical data DP-CPU-UC Interfaces to com- Video: 1 × Display-Port puter (DualMode standard 1.1) Keyboard and mouse signals 2 × PS/2 socket 1 × USB-B Audio: 2 × 3.5 mm jack plug Data transmission to Interface: 2 × RJ45 socket counterparts Transmission distance: Max.
Computer module »DVI-I-CPU« Computer module »DVI-I-CPU« With computer modules, you can connect a computer with graph- DVI-I-CPU ics output to a digital matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. Users at the consoles of the matrix switch can access the computer module and operate the connected computer.
Page 72
Computer module »DVI-I-CPU« Installation Connecting computers DVI-I CPU NOTE: Both keyboard and mouse signals can be transmitted to the computer using the PS/2 or the USB ports. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the purple PS/2 socket (keyboard) to this port.
Page 73
Computer module »DVI-I-CPU« Power supply Power In: Plug the power cable of the power pack in this interface. Then connect the power cable to the power pack and a power outlet. Status displays The LED on the back panel of the computer module shows the status of the external power pack: Status Meaning...
Page 74
Computer module »DVI-I-CPU« Technical data DVI-I-CPU Interfaces to Video: 1 × DVI-I computer: Keyboard and mouse signals: 2 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack socket Data transmission Interface: 1 × RJ45 socket to counterpart Transmission length Max.
Page 75
Computer module »DVI-I-CPU« DVI-I-CPU Power supply Type: Power pack(12 V/2 A) Connection: 1 × Mini-DIN 4 socket Current consumption: 0.5A @ 12 VDC Casing Material: Anodised aluminium Dimensions (W × H × D): Approx. 105 × 26 × 124 mm Weight: Approx.
Computer module »DVI-I-CPU-UC« Computer module »DVI-I-CPU-UC« With DVI-I-CPU-UC computer modules, you can connect a computer with graphics output to two different digital matrix switches of the ControlCenter-Compact or ControlCenter-Digital series. Users at the consoles of the matrix switch can access the computer module and operate the connected computer.
Page 77
Computer module »DVI-I-CPU-UC« Installation Connecting the computer DVI-I CPU NOTE: Both keyboard and mouse signals can be transmitted to the computer using the PS/2 or the USB ports. Use the purple plug of an optional Twin-PS/2 cable to connect the purple PS/ Keyb.: 2 socket (keyboard) to this port.
Page 78
Computer module »DVI-I-CPU-UC« Trans. 1: Connect this interface to a Dynamic Port (RJ45) of a matrix switch. Connect this interface to a Dynamic Port (RJ45) of another matrix switch. Trans. 2: NOTE: You can also connect the computer module directly to two compatible console modules.
Page 79
Computer module »DVI-I-CPU-UC« Technical data DVI-I-CPU-UC Interfaces to Video: 1 × DVI-I computer: Keyboard and mouse signals: 2 × PS/2 socket 1 × USB-B Audio: 2 × 3.5 mm jack socket Data transmission Interface: 2 × RJ45 sockets to counterparts Transmission length Max.
Page 80
Computer module »DVI-I-CPU-UC« DVI-I-CPU-UC Power supply Type: Power pack (12 V/2 A) Connection: 1 × Mini-DIN 4 socket Current consumption: 0.6A @ 12 VDC Casing Material: Anodised aluminium Dimensions (W × H × D): 105 × 26 × 124 mm Weight: Approx.
Computer module »DVI-I-CPU-Fiber« Computer module »DVI-I-CPU-Fiber« With computer modules, you can connect a computer with DVI-I-CPU-Fiber graphics output to a digital matrix switch of the ControlCenter-Compact or ControlCenter- Digital series. NOTE: This computer module can be connected to a compatible fiber port of ControlCenter-Compact matrix switches or ControlCenter-Digital matrix switches (requires CCD-I/O 16-Card-Fiber...
Page 82
Computer module »DVI-I-CPU-Fiber« Installation Connecting the computer DVI-I CPU NOTE: Keyboard and mouse signals can be transmitted to the computer using either the PS/2 interfaces or the USB interface. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the computer’s PS/2 keyboard interface to this interface.
Page 83
Computer module »DVI-I-CPU-Fiber« Connection to the matrix switch The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to as well as EN 60825-1:2014 U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 84
Computer module »DVI-I-CPU-Fiber« Status displays The LED on the back panel of the computer module shows the status of the external power pack: Status Meaning Power The external power pack is connected and the required voltage (12 Volt) is available. The external power pack is not (properly) connected.
Page 85
Computer module »DVI-I-CPU-Fiber« Technical data DVI-I-CPU-FIBER Interfaces to com- Video: 1 × DVI-I puter Keyboard and mouse signals 2 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission to Interface: 1 × LC-Duplex socket counterpart Transmission distance: ...
Page 86
Computer module »DVI-I-CPU-Fiber« DVI-I-CPU-FIBER Video DDC/CI: The device supports monitors with a DDC/CI function. The DDC information are transparently forwarded to the moni- tor to support a maximum number of monitors. However, the support cannot be guaranteed for all monitor models. Audio Transmission type: transparent, bidirectional...
Computer module »DVI-I-CPU-Fiber-UC« Computer module »DVI-I-CPU-Fiber-UC« With computer modules, you can connect a computer with DVI-I-CPU-Fiber-UC graphics output to two different matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. NOTE: This computer module can be connected to a compatible fiber port of ControlCenter-Compact matrix switches or ControlCenter-Digital matrix switches (requires CCD-I/O 16-Card-Fiber...
Page 88
Computer module »DVI-I-CPU-Fiber-UC« Installation Connecting the computer Keyb. Mouse USB K/M DVI-I CPU NOTE: Keyboard and mouse signals can be transmitted to the computer using either the PS/2 interfaces or the USB interface. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the computer’s PS/2 keyboard interface to this interface.
Page 89
Computer module »DVI-I-CPU-Fiber-UC« Connection to the matrix switch The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to as well as EN 60825-1:2014 U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 90
Computer module »DVI-I-CPU-Fiber-UC« Status displays The LED on the back panel of the computer module shows the status of the external power pack: Status Meaning Power The external power pack is connected and the required voltage (12 Volt) is available. The external power pack is not (properly) connected.
Page 91
Computer module »DVI-I-CPU-Fiber-UC« Technical data DVI-I-CPU-FIBER-UC Interfaces to Video: 1 × DVI-I computer Keyboard and mouse signals 2 × PS/2 socket 1 × USB-B Audio: 2 × 3,5 mm jack plug Data transmission to Interface: 2 × LC-Duplex socket matrix switches Transmission distance: ...
Page 92
Computer module »DVI-I-CPU-Fiber-UC« DVI-I-CPU-FIBER-UC Video DDC/CI: The device supports monitors with a DDC/CI function. The DDC information are transparently forwarded to the moni- tor to support a maximum number of monitors. However, the support cannot be guaranteed for all monitor models. Audio Transmission type: transparent, bidirectional...
Computer module »VGA-CPU-UC« Computer module »VGA-CPU-UC« With computer modules, you can connect a computer with a graph- VGA-CPU-UC ics output to two different digital matrix switches of the ControlCenter-Compact or ControlCenter-Digital series. Users at the consoles of the matrix switch can access the computer module to operate the connected computer.
Page 94
Computer module »VGA-CPU-UC« Installation Connecting the computer VGA CPU Keyb. Mouse USB K/M NOTE: Keyboard and mouse signals can be transmitted to the computer using either the PS/2 interfaces or the USB interface. Keyb.: Use the purple plug of an optional Twin-PS/2 cable to connect the computer’s PS/2 keyboard interface to this interface.
Page 95
Computer module »VGA-CPU-UC« Trans. 1: Connect this interface to a Dynamic Port (RJ45) of the first matrix switch. Connect this interface to a Dynamic Port (RJ45) of the second matrix switch. Trans. 2: ADVICE: You can also connect the computer module directly to up to two compatible console modules.
Page 96
Computer module »VGA-CPU-UC« Technical data VGA-CPU-UC Interfaces to com- Video: 1 × VGA puter Keyboard and mouse signals 2 × PS/2 socket 1 × USB-B Audio: 2 × 3.5 mm jack plug Data transmission to Interface: 2 × RJ45 socket counterparts Transmission distance: Max.
Page 97
Computer module »VGA-CPU-UC« VGA-CPU-UC Power supply Type: Portable power pack (12 V/2 A) Connector: 1 × Mini-DIN 4 socket Power input: 0.6A @ 12 VDC Housing Material: Anodised aluminium Dimensions (W × H × D): Approx. 105 × 26 × 104 mm Weight: Approx.
Computer module »U2-R-CPU« Computer module »U2-R-CPU« U2-CPU computer modules receive USB and RS232 signals from U2-CON console modules and transmit them to the computer. Package contents 1 × Computer module U2-R-CPU 1 × USB device cable 1 × RS232 cable ...
Page 99
Computer module »U2-R-CPU« Installation Connecting the computer RS232: Use the RS232 cable to connect the computer’s 9-pin serial computer inter- face to this interface (optional).
Trans.: Use a category 5e (or better) twisted pair cable to connect this interface to the Dynamic Port of the USB/RS232 Main Channel that is assigned to the computer.
Page 100
Computer module »U2-R-CPU« Technical data U2-R-CPU Interfaces to USB 2.0: 1 × USB-B target computer: RS232: 1 × D-SUB 9 socket Data transmission to Interface: 1 × RJ45 socket matrix switch Transmission length: Max. 140 metres USB 2.0 Transmission type: Transparent Transmission rate: Max.
Console modules Console module »DVI-CON« With DVI-CON console modules, you can connect a console ( monitor, keyboard, mouse and audio devices) to a digital matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. At the installed console, matrix switch users can access a computer module to operate the connected computer.
Page 102
Console module »DVI-CON« Installation Connecting the console devices LED out Mouse Generic Transmission Transmission DVI / VGA Out Micro In Speaker Keyb./Mouse Keyb. Red. Power Red. Power NOTE: Both keyboard and mouse signals can be transmitted to the computer using the PS/2 or the USB interfaces.
Page 103
Console module »DVI-CON« Connection to the matrix switch LED out LED out Mouse Mouse Generic Generic Transmission Micro In Micro In Keyb. Keyb. Red. Power Red. Power DVI / VGA Out DVI / VGA Out Speaker Speaker Keyb./Mouse Keyb./Mouse Use a category 5e (or better) twisted pair cable to connect the Transmis- Transmission: sion interface to a Dynamic Port (RJ45) of the matrix switch.
Page 104
Console module »DVI-CON« Status displays Front panel Power Status Console Service Service Ident. Video Red. Trans. Main System The LEDs on the front panel of the console module show the system’s operating status. Section Status Meaning Ident. Ident. On as soon as the LED has been activated via web application. Power Red.
Page 105
Console module »DVI-CON« Back panel LED out LED out Mouse Mouse Generic Generic Transmission Micro In Micro In Keyb. Keyb. Red. Power Red. Power DVI / VGA Out DVI / VGA Out Speaker Speaker Keyb./Mouse Keyb./Mouse The Transmission interface at the back panel of the console module provides additional status LEDs.
Page 106
Console module »DVI-CON« Technical data DVI-CON Interfaces to Video: 1 × DVI-I (DVI Single-Link or VGA) console: Keyboard and mouse signals: 2 × PS/2 socket 2 × USB-A Audio: 2 × 3.5 mm jack socket Tradeswitch-LED: 1 × D-SUB 9 socket Data transmission to Interface: 1 ×...
Page 107
Console module »DVI-CON« DVI-CON Operating Temperature: +5 °C to +45 °C environment Air humidity: 20 % to 80 %, non-condensing Storage Temperature: -20 °C to +60 °C environment Air humidity: 15 % to 85 %, non-condensing Conformity CE, UKCA, FCC class B, TAA, EAC, RoHS, WEEE, REACH 102 ·...
When using the console to access a computer module connected to a DVI-CPU-MC2 dual-head computer, the monitors display the separate images of the graphics out- puts. When accessing a computer module with one graphics input only, only the first monitor displays an image.
Page 109
Console module »DVI-CON-MC2« Installation Connecting console devices LED Out Mouse Generic Micro In Speaker DVI/VGA Out 2 Transmission 2 Transmission 2 Transmission 1 Transmission 1 DVI/VGA Out 1 Keyb./Mouse Keyb. Red. Power Red. Power Connect the first console monitor. DVI/VGA Out 1: DVI/VGA Out 2: Connect the second console monitor.
Page 110
Console module »DVI-CON-MC2« Connection to the matrix switch LED Out LED Out Mouse Mouse Generic Generic Micro In Speaker Micro In Speaker DVI/VGA Out 2 DVI/VGA Out 2 Keyb./Mouse Keyb./Mouse Keyb. Keyb. Red. Power Red. Power Transmission 2 Transmission 1 DVI/VGA Out 1 DVI/VGA Out 1 NOTE:...
Page 111
Console module »DVI-CON-MC2« Automatic channel grouping When operating the console module for the first time, the matrix switch recognises the main channel and the console module’s additional channel. The channels are auto- matically added to a channel group. The web application uses the following icons to mark the different types of channels: Main channel: computer and user superimposed by the digit 2 Video channel:...
Page 112
Console module »DVI-CON-MC2« Status displays Front panel Service Service Ident. Power Status Console Channel 2 Red. Trans. 1 Video 1 Video Main System Trans. Section Status Meaning Ident. Ident. On as soon as the LED has been activated via web application. Power Red.
Page 113
Console module »DVI-CON-MC2« Back panel LED Out LED Out Mouse Mouse Generic Generic Micro In Speaker Micro In Speaker DVI/VGA Out 2 DVI/VGA Out 2 Transmission 2 Transmission 1 DVI/VGA Out 1 DVI/VGA Out 1 Keyb./Mouse Keyb./Mouse Keyb. Keyb. Red. Power Red.
Page 114
Console module »DVI-CON-MC2« Technical data DVI-CON-MC2 Interfaces to console Video: 2 × DVI-I (DVI single-link or VGA) Keyboard and mouse signals 2 × PS/2 socket 2 × USB-A Audio: 2 × 3.5 mm jack plug Tradeswitch-LED: 1 × D-SUB 9 socket Data transmission to Interfaces: 2 ×...
Page 115
Console module »DVI-CON-MC2« DVI-CON-MC2 Operating Temperature: +5 °C to +45 °C environment Air humidity: 20 % to 80 %, non-condensing Storage Temperature: -20 °C to +60 °C environment Air humidity: 15 % to 85 %, non-condensing Conformity CE, UKCA, FCC class B, TAA, EAC, RoHS, WEEE, REACH 110 ·...
NOTE: Connecting a multi-monitor computer with four video outputs requires four computer modules of the series or two computer modules of the DVI-CPU DVI-CPU- series. In the web application, you can add the computer modules of the multi-monitor computers to a channel groups More information about this topic is given in the chapter Expanding the system through port grouping of the web application manual.
Page 117
Console module »DVI-CON-MC4« Installation Connecting the console devices LED out Mouse Transmission 1 DVI / VGA Out 1 Micro In Speaker Keyb. Red. Power Transmission 2 DVI / VGA Out 2 Transmission 3 Connect the first console monitor. DVI/VGA Out 1: DVI/VGA Out 2: Connect the second console monitor.
Page 118
Console module »DVI-CON-MC4« Connection to the matrix switch LED out Mouse Generic Transmission 1 DVI / VGA Out 1 Micro In Speaker Keyb./Mouse Keyb. Red. Power Transmission 2 DVI / VGA Out 2 Transmission 3 NOTE: Use category 5e (or better) twisted pair cables to connect the devices. ADVICE: You can also connect the console module directly to a compatible computer module.
Page 119
Console module »DVI-CON-MC4« Startup Turn on the console module after its installation. Use the Main Power power pack or a redundant power pack to establish the power supply: Turn on the Main Power power pack. Use an optional power pack to supply the Red.
Page 120
Console module »DVI-CON-MC4« Status displays Front panel Ident. Power Status Console Service Service Channel 2 Red. Trans. 1 Video 1 Video Main System Trans. Section Status Meaning Power Red. The optional power pack is connected and supplies 12 Volt. The optional power pack is not (properly) connected. Main The power pack is turned on and supplies the required voltage.
Page 121
Console module »DVI-CON-MC4«
Video 3 Strong video signal atthird video input. No signal at third video input, or the signal quality is too weak to be processed by the system. Trans. 3 The communication to the counterpart is established successfully.
Page 122
Console module »DVI-CON-MC4« Back panel LED out Mouse Generic Transmission 1 DVI / VGA Out 1 Micro In Speaker Keyb./Mouse Keyb. Red. Power Transmission 2 DVI / VGA Out 2 Transmission 3 The Transmission interfaces at the console module’s back panel provide additional status LEDs.
Page 123
Console module »DVI-CON-MC4« Technical data DVI-CON-MC4 Interfaces to console Video: 4 × DVI-I (DVI Single-Link or VGA) Keyboard and mouse signals 2 × PS/2 socket 2 × USB-A Audio: 2 × 3.5 mm jack plug Tradeswitch-LED: 1 × D-SUB 9 socket Data transmission to Interfaces: 4 ×...
Page 124
Console module »DVI-CON-MC4« DVI-CON-MC4 Operating Temperature: +5 °C to +45 °C environment Air humidity: 20 % to 80 %, non-condensing Storage Temperature: -20 °C to +60 °C environment Air humidity: 15 % to 85 %, non-condensing Conformity CE, EAC, FCC Class B, RoHS Computer and console modules ·...
Console module »DVI-CON-2« Console module »DVI-CON-2« With console modules, you can connect a console ( monitor, keyboard, DVI-CON-2 mouse and audio devices) to two digital matrix switches of the ControlCenter-Compact or ControlCenter-Digital series. At the installed console, matrix switch users can access a computer module to operate the connected computer.
Page 126
Console module »DVI-CON-2« Installation Connecting the console devices Transmission 2 Transmission 2 LED out Mouse Generic Transmission 1 Transmission 1 DVI / VGA Out Micro In Speaker Keyb./Mouse Keyb. Red. Power Red. Power DVI/VGA Out: Connect the monitor/projector of the local console. Connect the optional microphone of the local console.
Page 127
Console module »DVI-CON-2« Connection to the matrix switch Transmission 2 LED out LED out Mouse Mouse Generic Generic Transmission 1 DVI / VGA Out DVI / VGA Out Micro In Micro In Speaker Speaker Keyb./Mouse Keyb./Mouse Keyb. Keyb. Red. Power Red.
Page 128
Console module »DVI-CON-2« Switching The buttons on the front panel of the console module or configured key combina- tions (select keys) let users switch between the connected matrix switches. How to switch channels via buttons: Press the button of the desired channel to activate it. How to switch channels via key combinations: ...
Page 129
Console module »DVI-CON-2« Status displays Front panel Trans. 1 Trans. 2 Active Status Ident. Power Status Console Service Service Video Red. Trans. Main System The LEDs on the front panel of the console module show the system’s operating status. Section Status Meaning Ident.
Page 130
Console module »DVI-CON-2« Section Status Meaning Trans. Active Active channel. Inactive channel. Status The communication with the counterpart of this channel was established successfully. The communication with the counterpart of this active channel could not be established. Back panel Transmission 2 LED out LED out Mouse...
Page 131
Console module »DVI-CON-2« Technical data DVI-CON-2 Interfaces to Video: 1 × DVI-I (DVI Single-Link or VGA) console Keyboard/mouse signals 2 × PS/2 socket 3 × USB-A Audio: 2 × 3.5 mm jack socket Tradeswitch-LED: 1 × D-SUB 9 scoket Data transmission to Interface: 2 ×...
Page 132
Console module »DVI-CON-2« DVI-CON-2 Operating Temperature: +5 °C to +45 °C environment Air humidity: 20 % to 80 %, non-condensing Storage Temperature: -20 °C to +60 °C environment Air humidity: 15 % to 85 %, non-condensing Conformity CE, UKCA, FCC class B, TAA, EAC, RoHS, WEEE, REACH Computer and console modules ·...
Console module »DVI-CON-Fiber« Console module »DVI-CON-Fiber« With console modules, you can use optical fibres to connect a console DVI-CON-Fibre monitor, keyboard, mouse and audio devices) to the matrix switch of the ControlCenter-Compact or ControlCenter-Digital series NOTE: This console module can be connected to a compatible fiber port of ControlCenter-Compact matrix switches or ControlCenter-Digital matrix switches (requires CCD-I/O 16-Card-Fiber...
Page 134
Console module »DVI-CON-Fiber« Installation Connecting the console devices LED out Mouse Generic Micro In Speaker Transmission Transmission DVI / VGA Out Keyb./Mouse Keyb. Red. Power Red. Power NOTE: Both keyboard and mouse signals can be transmitted to the computer using the PS/2 or the USB interfaces.
Page 135
Console module »DVI-CON-Fiber« Connection to the matrix switch The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to as well as EN 60825-1:2014 U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 136
Console module »DVI-CON-Fiber« Power supply LED out LED out Mouse Mouse Generic Generic Micro In Micro In Speaker Speaker Transmission Transmission DVI / VGA Out DVI / VGA Out Keyb./Mouse Keyb./Mouse Keyb. Keyb. Red. Power Main Power: Connect the power cable with the power pack and a power socket. Connect the cable of the optional power pack to establish a redundant Red.
Page 137
Console module »DVI-CON-Fiber« Status displays Front panel Power Console Service Service Ident. Status Video Red. Trans. System Main The LEDs on the front panel of the console modules show the system’s operating status. Section Status Meaning Ident. Ident. On as soon as the LED has been activated via web application. Power Red.
Page 138
Console module »DVI-CON-Fiber« Back panel LED out LED out Mouse Mouse Generic Generic Micro In Micro In Speaker Speaker Transmission DVI / VGA Out DVI / VGA Out Keyb./Mouse Keyb./Mouse Keyb. Keyb. Red. Power Red. Power The back panel of the console module provides additional status LEDS. They have the following meaning: Interface Status...
Page 139
Console module »DVI-CON-Fiber« Technical data DVI-CON-FIBER Interfaces to console Video: 1 × DVI-I (DVI Single-Link or VGA) Keyboard and mouse signals 2 × PS/2 socket 3 × USB-A Audio: 2 × 3.5 mm jack plug Tradeswitch-LED: 1 × D-SUB 9 socket Data transmission to Interfaces: 1 ×...
Page 140
Console module »DVI-CON-Fiber« DVI-CON-FIBER Main power supply Type: Internal power pack Connector: 1 × IEC plug (IEC-320 C14) Power input: 100 - 240 VAC; 0.3 A - 0.2 A Redundant Type: Portable power pack (12 V/2 A) power supply Connector: 1 ×...
When using the console to access a computer module connected to a DVI-CPU-MC2 dual-head computer, the monitors display the separate images of the graphics out- puts. When accessing a computer module with one graphics input only, only the first monitor displays an image.
Page 142
Console module »DVI-CON-Fiber-MC2« Package contents 1 × Console module DVI-CON-Fiber-MC2 1 × Power cable 1 × »Manual information« flyer 1 × »Safety instructions« flyer Required accessories 2 × Compatible optical fibre cable to connect the console module to a KVM matrix switch or compatible computer modules Computer and console modules ·...
Page 143
Console module »DVI-CON-Fiber-MC2« Installation Connecting console devices LED Out Mouse Generic Transmission 2 DVI/VGA Out 2 Transmission 1 DVI/VGA Out 1 Micro In Speaker Keyb./Mouse Keyb. Red. Power DVI/VGA Out 1: Connect the first console monitor. Connect the second console monitor. DVI/VGA Out 2: Micro In: Connect the console microphone (optional).
Page 144
Console module »DVI-CON-Fiber-MC2« Connection to the matrix switch IMPORTANT: The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to EN 60825-1:2014 as well as U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 145
Console module »DVI-CON-Fiber-MC2« Power supply LED Out Mouse Generic Transmission 2 DVI/VGA Out 2 Transmission 1 DVI/VGA Out 1 Micro In Speaker Keyb./Mouse Keyb. Red. Power Main Power: Connect the supplied power cable. Insert the cable’s Schuko plug in a power socket.
Page 146
Console module »DVI-CON-Fiber-MC2« Automatic channel grouping When operating the console module for the first time, the matrix switch recognises the main channel and the console module’s additional channel. The channels are auto- matically added to a channel group. The web application uses the following icons to mark the different types of channels: computer and user superimposed by the digit 2 Main channel: multiple monitors in a row...
Page 147
Console module »DVI-CON-Fiber-MC2« Status displays Front panel Service Ident. Power Status Console Channel 2 Red. Trans. 1 Video 1 Video Main System Trans. Section Status Meaning Ident. Ident. On as soon as the LED has been activated via web application. Power Red.
Page 148
Console module »DVI-CON-Fiber-MC2« Back panel LED Out Mouse Generic Transmission 2 DVI/VGA Out 2 Transmission 1 DVI/VGA Out 1 Micro In Speaker Keyb./Mouse Keyb. Red. Power The Transmission interfaces at the console module’s back panel provide additional status LEDs. Interface Status Meaning Transmission...
Page 149
Console module »DVI-CON-Fiber-MC2« Technical data DVI-CON-FIBER-MC2 Interfaces to console Video: 2 × DVI-I (DVI single-link or VGA) Keyboard and mouse signals 2 × PS/2 socket 3 × USB-A Audio: 2 × 3.5 mm jack plug Tradeswitch-LED: 1 × D-SUB 9 socket Data transmission to Interface: 2 ×...
Page 150
Console module »DVI-CON-Fiber-MC2« DVI-CON-FIBER-MC2 Main power supply Type: Internal power pack Connector: 1 × IEC plug (IEC-320 C14) Power input: 100 - 240 VAC; 0.4 A - 0.2 A Redundant Type: External power pack power supply Connector: 1 × Mini-DIN 4 socket Power input: 1.6A @ 12 VDC Housing...
NOTE: Connecting a multi-monitor computer with four video outputs requires four computer modules of the DVI-CPU series or two computer modules of the DVI-CPU- series. In the web application, you can add the computer modules of the multi-monitor computers to a channel groups More information about this topic is given in the chapter Expanding the system through port grouping of the web application manual.
Page 152
Console module »DVI-CON-Fiber-MC4« Installation Connecting the console devices Mouse LED Out Generic Transmission 2 DVI/VGA Out 2 Transmission 1 DVI/VGA Out 1 Micro In Speaker Keyb./Mouse Keyb. Red. Power Connect the first console monitor. DVI/VGA Out 1: DVI/VGA Out 2: Connect the second console monitor.
Page 153
Console module »DVI-CON-Fiber-MC4« Connection to the matrix switch IMPORTANT: The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to as well as EN 60825-1:2014 U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 154
Console module »DVI-CON-Fiber-MC4« Transmission 4|Tx: Insert the LC plug of a compatible optical fibre cable. Connect the other end of the cable to the interface of another Dynamic Port provided at the matrix switch. Transmission 4|Rx: Insert the LC plug of a compatible optical fibre cable. Connect the other end of the cable to the interface of the same Dynamic Port provided at the matrix switch.
Page 155
Console module »DVI-CON-Fiber-MC4« Automatic channel grouping When operating the console module for the first time, the matrix switch recognises the main channel and the console module’s additional channel. The channels are auto- matically added to a channel group. The web application uses the following icons to mark the different types of channels: Main channel: computer and user superimposed by the digit 2 Video channel:...
Page 156
Console module »DVI-CON-Fiber-MC4« Status displays Front panel Ident. Service Power Status Console Channel 2 Red. Trans. 1 Video 1 Video Main System Trans. Section Status Meaning Ident. Ident. On as soon as the LED has been activated via web application. Power Red.
Page 157
Console module »DVI-CON-Fiber-MC4« Service Channel 2 Channel 3 Channel 4 Video Video Video Trans. Trans. Trans. Channel 3 Video Strong video signal atthird video input. No signal at third video input, or the signal quality is too weak to be processed by the system. Trans.
Page 158
1 × D-SUB 9 socket Data transmission to Interface: 2 × LC-Duplex socket counterpart Transmission distance: DVI-CPU-Fiber-MC4(M) Max. 100 Meter (62,5μ/125μ), Max. 200 Meter (50μ/125μ OM2) Max. 400 Meter (50μ/125μ OM3) DVI-CPU-Fiber-MC4(S) Max. 5.000 Meter (9μ/125μ OS1) DVI-CPU-Fiber-MC4(S+) Max.
Page 159
Console module »DVI-CON-Fiber-MC4« DVI-CON-FIBER-MC4 Main power supply Type: Internal power pack Connector: 1 × IEC plug (IEC-320 C14) Power input: 100 - 240 VAC; 0.6 A - 0.3 A Redundant Type: External power pack power supply Connector: 1 × Mini-DIN 4-Buchse Power input: 2.6A @ 12 VDC Housing...
Console module »DVI-CON-2-Fiber« Console module »DVI-CON-2-Fiber« With DVI-CON-2-Fiber console modules, you can connect a console ( monitor, key- board, mouse and audio devices) to two digital matrix switches of the ControlCenter- Compact or ControlCenter-Digital series. NOTE: This console module can be connected to a compatible fiber port of ControlCenter-Compact matrix switches or ControlCenter-Digital matrix switches (requires CCD-I/O 16-Card-Fiber...
Page 161
Console module »DVI-CON-2-Fiber« Installation Connecting the console devices Transmission 2 Transmission 2 LED Out Mouse Generic Transmission 1 Transmission 1 DVI/VGA Out Micro In Speaker Keyb./Mouse Keyb. Red. Power Red. Power Connect the monitor of the local console. DVI/VGA Out: Micro In: Connect the optional microphone of the local console.
Page 162
Console module »DVI-CON-2-Fiber« Connection to the matrix switches IMPORTANT: The devices use components with laser technology which comply with laser class 1. They meet the requirements in accordance to EN 60825-1:2014 as well as U.S. CFR 1040.10 1040.11 Mind the following instructions when dealing with laser beams: ...
Page 163
Console module »DVI-CON-2-Fiber« Power supply Transmission 2 Transmission 2 LED Out LED Out Mouse Mouse Generic Generic Transmission 1 Transmission 1 DVI/VGA Out DVI/VGA Out Micro In Speaker Micro In Speaker Keyb./Mouse Keyb./Mouse Keyb. Keyb. Red. Power Main Power: Connect the power cable to the power pack and a power outlet. Red.
Page 164
Console module »DVI-CON-2-Fiber« Status displays Front panel Trans. 1 Trans. 2 Active Status Ident. Service Service Power Status Console Red. Trans. Video Main System The LEDs on the front panel of the console module show the system’s operating status. Section Status Meaning Ident.
Page 165
Console module »DVI-CON-2-Fiber« Back panel Transmission 2 LED Out LED Out Mouse Mouse Generic Generic Transmission 1 DVI/VGA Out DVI/VGA Out Micro In Speaker Micro In Speaker Keyb./Mouse Keyb./Mouse Keyb. Keyb. Red. Power Red. Power The Transmission interface at the back panel of the console module provides additional status LEDs.
Page 166
Console module »DVI-CON-2-Fiber« Technical data DVI-CON-2-FIBER Interfaces to Video: 1 × DVI-I (DVI Single-Link oder VGA) console Keyboard/mouse signals 2 × PS/2 socket 3 × USB-A Audio: 2 × 3.5 mm jack socket Tradeswitch-LED: 1 × D-SUB 9 scoket Data transmission to Interface: 2 ×...
Page 167
Console module »DVI-CON-2-Fiber« DVI-CON-2-FIBER Main power supply Type: Internal power pack Connection: 1 × IEC plug (IEC-320 C14) Power input: 100 - 240 VAC; 0.3 A - 0.2 A Redundant Type: Portable power pack (12 V/2 A) power supply Connection: 1 ×...
Console module »DVI-CON-12V« Console module »DVI-CON-12V« With DVI-CON-12V console modules, you can connect a console ( monitor, key- board, mouse and audio devices) to a digital matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. At the installed console, matrix switch users can access a computer module to operate the connected computer.
Page 169
Console module »DVI-CON-12V« Installation LED Out Mouse Transmission Micro In Speaker Keyb./Mouse Keyb. Red. Power Main Power DVI/VGA Out Connecting the console devices NOTE: Both keyboard and mouse signals can be transmitted to the computer using the PS/2 or the USB interfaces. Connect the PS/2 keyboard of the local console.
Page 170
Console module »DVI-CON-12V« Status displays Front panel Power Status Console Service Video Red. Trans. Main System The LEDs on the front panel of the console module show the system’s operating status. Section Status Meaning Power Red. The optional power pack is connected and supplies 12 Volt. The optional power pack is not (properly) connected.
Page 171
Console module »DVI-CON-12V« Back panel LED Out Mouse Transmission DVI/VGA Out Micro In Speaker Keyb./Mouse Keyb. Red. Power Main Power The Transmission interface at the back panel of the console module provides addi- tional status LEDs. The LEDs have the following meaning: Interface Status Meaning...
Page 172
Console module »DVI-CON-12V« Technical data DVI-CON-12V Interfaces to Video: 1 × DVI-I (DVI Single-Link or VGA) console: Keyboard and mouse signals: 2 × PS/2 socket 2 × USB-A Audio: 2 × 3.5 mm jack socket Tradeswitch-LED: 1 × D-SUB 9 socket Data transmission Interface: 1 ×...
Page 173
Console module »DVI-CON-12V« DVI-CON-12V Casing Material: Anodised aluminium Dimensions (W × H × D): Approx. 210 × 44 × 210 mm Weight: Approx. 1.3 kg Operating Temperature: +5 °C to +45 °C environment Air humidity: 20 % to 80 %, non-condensing Storage Temperature: -20 °C to +60 °C...
Page 174
Console module »DVI-CON-12V« Pin assignment of the 4-pin Mini-DIN socket (12 V) Pin no. Line +12 V +12 V Computer and console modules · 169...
Console module »DVI-CON-Video« Console module »DVI-CON-Video« With console modules, you can connect a monitor or a projector to DVI-CON-Video a matrix switch of the ControlCenter-Compact or ControlCenter-Digital series. First connect the monitor or the projector and the audio devices) to the console module.
Page 176
Console module »DVI-CON-Video« Installation Connecting the console devices LED Out Transmission Transmission DVI/VGA Out Micro In Speaker Red. Power Red. Power DVI/VGA Out: Connect the monitor/projector of the local console. Micro In: Connect the optional microphone of the local console. Connect the optional speakers of the local console.
Page 177
Console module »DVI-CON-Video« Power supply LED Out LED Out Transmission Transmission DVI/VGA Out DVI/VGA Out Micro In Speaker Micro In Speaker Red. Power Main Power: Connect the power cable to the power pack and a power outlet. Red. Power: If required, connect the power cable of the optional power pack to this interface.
Page 178
Console module »DVI-CON-Video« Start-up Start the console module by pressing the Main Power button of the power pack. ADVICE: The active hotkey configuration is displayed during the System Startup of the matrix switch. Status displays Front panel Power Status Console Service Service Ident.
Page 179
Console module »DVI-CON-Video« Back panel LED Out LED Out Transmission Micro In Speaker Micro In Speaker Red. Power Red. Power DVI/VGA Out DVI/VGA Out The Transmission interface at the back panel of the console module provides additional status LEDs. The LEDs have the following functions: Interface Status Meaning...
Page 180
Console module »DVI-CON-Video« Technical data DVI-CON-VIDEO Interfaces to Video: 1 × DVI-I (DVI Single-Link or VGA) console: Audio: 2 × 3.5 mm jack socket Tradeswitch-LED: 1 × D-SUB 9 socket Data transmission to Interface: 1 × RJ45 socket counterpart Transmission length: Max.
Page 181
Console module »DVI-CON-Video« DVI-CON-VIDEO Casing Material: Anodised aluminium Dimensions (W × H × D): Approx. 210 × 44 × 210 mm Weight: Approx. 1.21 kg Operating Temperature: +5 °C to +45 °C environment Air humidity: 20 % to 80 %, non-condensing Storage Temperature: -20 °C to +60 °C...
Console module »DP-CON« Console module »DP-CON« With DP-CON console modules, you can connect a console ( DisplayPort monitor, key- board, mouse and audio devices) to a digital matrix switch of the ControlCenter- Compact or ControlCenter-Digital series. At the installed console, matrix switch users can access a computer module to operate the connected computer.
Page 183
Console module »DP-CON« Installation Connecting the console devices LED out Mouse Generic Transmission DisplayPort Out Micro In Speaker Keyb./Mouse Keyb. Red. Power NOTE: Both keyboard and mouse signals can be transmitted to the computer using the PS/2 or the USB interfaces. Keyb.: Connect the PS/2 keyboard of the local console.
Page 184
Console module »DP-CON« Connection to the matrix switch Use a category 5e (or better) twisted pair cable to connect the Transmis- Transmission: sion interface to a Dynamic Port (RJ45) of the matrix switch. NOTE: You can also connect the console module directly to a compatible computer module.
Page 185
Console module »DP-CON« Status displays Front panel Console Service Power Status Red. Trans. Video Main System The LEDs on the front panel of the console module show the system’s operating status. Section Status Meaning Power Red. The optional power pack is connected and supplies 12 Volt. The optional power pack is not (properly) connected.
Page 186
Console module »DP-CON« Back panel LED out Mouse Generic Transmission DisplayPort Out Micro In Speaker Keyb./Mouse Keyb. Red. Power The Transmission interface at the back panel of the console module provides addi- tional status LEDs. The LEDs have the following meaning: Interface Status Meaning...
Page 187
Console module »DP-CON« Technical data DP-CON Interfaces to Video: 1 × DisplayPort socket console: Keyboard and mouse signals: 2 × PS/2 socket 2 × USB-A Audio: 2 × 3.5 mm jack socket USB: 4 × USB-A socket Tradeswitch-LED: 1 × D-SUB 9 socket Data transmission to Interface: 1 ×...
Page 188
Console module »DP-CON« DP-CON Casing Material: Anodised aluminium Dimensions (W × H × D): Approx. 210 × 44 × 210 mm Weight: Approx. 1.3 kg Operating Temperature: +5 °C to +45 °C environment Air humidity: 20 % to 80 %, non-condensing Storage Temperature: -20 °C to +60 °C...
Console module »DP-CON-2« Console module »DP-CON-2« With console modules, you can connect a console ( monitor, DP-CON-2 DisplayPort keyboard, mouse and audio devices) to two digital matrix switches of the Control- Center-Compact or ControlCenter-Digital series. At the installed console, matrix switch users can access a computer module to operate the connected computer.
Page 190
Console module »DP-CON-2« Installation Connecting the console devices Transmission 2 LED out Mouse Generic Transmission 1 DisplayPort Out Micro In Speaker Keyb./Mouse Keyb. Red. Power Connect the monitor/projector of the local console. DisplayPort Out: NOTE: Check the monitor's manual if the OSD provides a setting for the mode of the DisplayPort input.
Page 191
Console module »DP-CON-2« Connection to the matrix switch NOTE: Use category 5e (or better) twisted pair cables to connect the devices. Connect this interface to a Dynamic Port (RJ45) of the matrix switch. Transmission 1: Transmission 2: Connect this interface to another Dynamic Port (RJ45) of the matrix switch.
Page 192
Console module »DP-CON-2« Status displays Front panel Trans. 1 Trans. 2 Active Status Console Service DP-CON-2 Power Status Video Red. Trans. Main System The LEDs on the front panel of the console module show the system’s operating status. Section Status Meaning Power Red.
Page 193
Console module »DP-CON-2« Section Status Meaning Trans. Active Active channel. Inactive channel. Status The communication with the counterpart station of this channel was established successfully. The communication with the counterpart station of this active channel could not be established. Back panel Transmission 2 LED out Mouse...
Page 194
Console module »DP-CON-2« Technical data DP-CON-2 Interfaces to Video: 1 × DisplayPort socket console Keyboard/mouse signals 2 × PS/2 socket 3 × USB-A Audio: 2 × 3.5 mm jack socket USB: 4 × USB-A socket Tradeswitch-LED: 1 × D-SUB 9 scoket Data transmission to Interface: 2 ×...
Page 195
Console module »DP-CON-2« DP-CON-2 Casing Material: Anodised aluminium Dimensions (W × H × D): Approx. 210 × 44 × 210 mm Weight: Approx. 1.3 kg Operating Temperature: +5 °C to +45 °C environment Air humidity: 20 % to 80 %, non-condensing Storage Temperature: -20 °C to +60 °C...
Console module »U2-R-CON« Console module »U2-R-CON« U2-R-CON console module transmits USB and RS232 signals from the console to U2-R-CPU computer module. Package contents 1 × console module U2-R-CON 1 × Power pack (12V/2A, only with variants incl. PowerPack) ...
Page 197
Console module »U2-R-CON« Status displays The blinking Transmission LEDs show the following connection statuses: Colour Status Meaning Left Yellow No connection to network. A console module is accessing the computer module. Right Green A console module is accessing the computer module. Blinking No communication with the counterpart.
Generic HID Generic HID mode, data of the USB input device connected to the Generic socket of the console module remains unaltered when transmitted to the active computer module. The use of Generic HID devices is possible only after you enable the Generic HID mode of the console module and of the computer module.
Enabling/disabling the computer module’s Generic HID mode 4. Select Generic HID and press to select one of the following options: off: Connect either a USB keyboard or a USB mouse to the console module’s Generic interface. The data of any USB input device connected to the console module’s Generic interface remains unaltered when transmitted to the active computer module.
Page 200
Enabling/disabling the computer module’s Generic HID mode 5. Select USB keyboard and press to select one of the following options. Multimedia: PC keyboard with additional multimedia keys (default) Standard: PC keyboard with standard keyboard layout Generic: Any USB input device NOTE: USB computer modules additionally support certain USB input devices.
Extender mode The console modules and the computer modules for the digital matrix switch can be operated in extender mode. Connect a console module directly with a compatible computer module. Use the same cable types as for the connection of a matrix switch (see Installation). NOTE: Older modules may require a crossover cable to connect both modules.
Configuration Configuration With the console module’s OSD, you can view and change the settings in extender mode. Changing the hotkey to open the OSD When in extender mode, press Alt+Num (default) to open the console module’s local OSD. NOTE: The hotkey consists of at least one hotkey modifier key and an additional hotkey, which you can select from multiple options.
Page 203
Configuration Num: Num key Pause: Pause key Insert: Insert key Delete: Delete key Home: Home key End: End key PgUp: Page Up key PgDn: Page Down key Space: Space key 5. Press to save your settings. Opening the OSD via double keypress In addition to opening the OSD with the key combination Alt+Num , you can open...
Page 204
Configuration Changing the select keys NOTE: Select keys can only be used and configured at console modules providing at least two channels (e. g. DVI-CON-2 In the default settings, the select keys are active to switch between the con- nected computer modules. You can also select another set of select keys.
Page 205
Configuration How to transmit the EDID profile of the connected monitor to the computer module: 1. Press the Alt+Num (default) hotkey to open the OSD. 2. Select and press EDID Enter 3. Select Send monitor‘s EDID and press Enter 4. Press to close the EDID menu.
Page 206
Configuration 4. Now the Edit Generic HID dialogue opens showing a list of detected devices. The font colour of the names of the HID devices indicates whether the devices have been activated (green) or not activated (yellow) by the USB host. In the Show field, you can change the entries shown in the list field.
Page 207
Configuration Adjusting the scancode set of a PS/2 keyboard If a key is pressed on the PS/2 keyboard, the keyboard processor sends a data packet that is called scan code. The two common scan code sets (sets 2 and 3) contain dif- ferent scan codes.
Page 208
Configuration 3. Select the USB Auto Refresh entry and press to select the keyboard type: off: The connected USB input devices do not need to be reini- tialised (recommended setting). all: All USB devices are regularly reinitialised. only faulty: The status of USB devices is monitored. If the communica- tion with a USB devices is interrupted, the device is reini- tialised.
Page 209
Configuration Choosing the USB keyboard mode NOTE: This setting has only an impact if a USB cable connects the computer module to the computer. USB computer modules support different USB input devices. You can use the special features of a USB input device after selecting the specific USB keyboard mode. In addition to the keys of standard keyboard layouts, the default ...
Page 210
Configuration LK463 compatible keyboard: You can connect an LK463 compatible keyboard to the console modules of the KVM matrix system. The order of the 108 keys of these key- boards is the same as the OpenVMS keyboard layout. A special USB keyboard mode guarantees that the keypress of a special key on this keyboard is forwarded to the computer: INPUT DEVICE SETTING...
Page 211
Configuration When using a standard keyboard, you can perform these functions by using the key combinations listed below: KEY COMBINATIONS »SOLARIS SHORTCUT KEY« OF SUN KEYBOARDS Ctrl+Alt+F2 Again Ctrl+Alt+F3 Props Ctrl+Alt+F4 Undo Ctrl+Alt+F5 Front Ctrl+Alt+F6 Copy Ctrl+Alt+F7 Open Ctrl+Alt+F8 Paste Ctrl+Alt+F9 Find Ctrl+Alt+F10...
Page 212
Configuration Enable/disable the startup without a keyboard By default, console modules start without a keyboard. As an alternative, the console module can interrupt startup by showing a message regarding the missing keyboard. Once you connect a keyboard to the console module, the startup process continues. How to enable/disable the startup of a console module without a keyboard: 1.
Page 213
Configuration 3. Select one of the following functions and press Enter Reset Mouse: Resets the PS/2 mouse interface of a Windows computer Enable mouse (for Unix): Activates the PS/2 mouse of a Linux computer Enable Intelli: Activates the PS/2 wheel mouse of a Linux computer Enable Intelli-Explorer: Activates the PS/2 wheel mouse with additional keys of a Linux computer...
Page 214
Configuration HOTKEY Local Hotkey (Modifier+Key) Modifier: Modifier key of key combination Key: Hotkey of key combination Local OSD via 2x keypress Modifier: Configured key to oprn the on-screen display via double keypress Local selectkeys Keys: Selected set of select keys: HARDWARE INFORMATION Serial number: Serial number of console module...
Page 216
G&D. FEELS RIGHT. Hauptsitz | Headquarter US-Büro | US-Office Guntermann & Drunck GmbH Systementwicklung G&D North America Inc. Obere Leimbach 9 | D-57074 Siegen | Germany 4540 Kendrick Plaza Drive, Suite 100 | Houston, TX 77032 | USA Phone +49 271 23872-0 Phone +1-346-620-4362 sales@gdsys.com | www.gdsys.com sales.us@gdsys.com | www.gdsys.com...
Need help?
Do you have a question about the DVI-CPU and is the answer not in the manual?
Questions and answers