1. Manuals
  2. Brands
  3. Ice Manuals
  4. Arcade Game Machines
  5. SNOWBALL TOSS
  6. Assembly instructions manual

Ice SNOWBALL TOSS Assembly Instructions Manual

Hide thumbs Also See for SNOWBALL TOSS:
Table of Contents

Advertisement

Quick Links

Download this manual
1

Advertisement

Table of Contents
loading

Related Manuals for Ice SNOWBALL TOSS

Summary of Contents for Ice SNOWBALL TOSS

  • Page 2: Table Of Contents

    Table of Contents Safety, Warnings, and Power Requirements Marquee Setup Game Controls and Meters Automatic Game Settings Program Options Recommended Bonus Values Error Codes Troubleshooting and Technical Information Tilt - Cheat Sensor The Ball gate Assembly Reset shelf Graphics Warranty Rev C 1/13/2020...

  • Page 3: Safety, Warnings, And Power Requirements

    SAFETY AND WARNINGS BEFORE YOU BEGIN WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED. FAIL- URE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE A GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO THE ELECTRONICS.

  • Page 4: Marquee Setup

    Step 1: Attach the supports arms to the marquee center with three AA6480 Allen bolts and AA6075 washers. Make sure to route the wire harness through the wire access hole. Connect the LED harness. Assembled Step 2: Lift the marquee with a helper onto the top of two games pushed side by side.
  • Page 5 Step 3: Secure the marquee to the cabinets using three AA6480 Allen bolts and AA6075 washers on each side..
  • Page 6 Step 4: Remove the marquee back cover by removing the four screws shown with the arrows. Insert both phone style cables through the back door and plug into the marquee board (picture 1). Then take the other end and insert it through the roof (picture 2). Secure the cable down the same side as the cheat sensor wiring at the front, on the right side (from the front of the cabinet).

  • Page 7: Game Controls And Meters

    Game controls and Meters Located on the center door is the operators control panel. There you can quickly adjust the volume of the game by pressing the “UP” and “DOWN” push buttons. You can view how many coin pulses and tickets has been paid by viewing the meters. To adjust the game’s programming, press the “PROG”...
  • Page 8 Programming Op琀椀ons for Snowball Op琀椀on Number Value Op琀椀on Default Short Descrip琀椀on Game Volume Game Volume This op琀椀on adjusts the general game sounds. Music Volume Music Volume This op琀椀on adjusts the music in the game and a琀琀ract mode. Coin 1 Cost of Game How many pulses to start your game.

  • Page 9: Recommended Bonus Values

    Score 0 - 40 Tickets for Zone Sets the amount of 琀椀ckets to win when 0 to 40 points are scored. See Score chart below. Also is used for giving 琀椀ckets just for playing. Score 50 - 140 Tickets for Zone Sets the amount of 琀椀ckets to win when 50-90 points are scored.

  • Page 10: Error Codes

    If you can play the game, then the fault is likely the cheat sensor or a short in the harness- ing. Replacement ICE part number BL1332X. If you cannot play the game, then contact ICE tech support to have your board sent in for repair or request an advance replacement.

  • Page 11: The Ball Gate Assembly

    The Ball Gate Assembly: Technical Informa琀椀on Two half-moons a琀琀ached together and connected to a single motor. The posi琀椀on of the le昀琀 half-moon is sensed by two reed switches. A small magnet is located under the le昀琀 moon. When the reed switch is ac琀椀vated, it will be at 0 VDC, the other will be opposite, +5 VDC.
  • Page 12 Ball-gate sensors Access Remove the two screws that hold the gate cam to the Primary Ball gate assembly. Slide the Primary Ball gate assembly out. Gate Cam Primary Ball Gate Ball-gate sensors Opera琀椀on There are two magne琀椀c sensors located under the primary ball gate assembly. The primary ball gate assembly has a magne琀椀c a琀琀ached underneath so that when the assembly rotates it will pass over one of the two sensors.

  • Page 13: Reset Shelf

    RESET SHELF EXPLAINED The main board controls the two shelf motors. Each shelf sensor has its own output back to the main board. When a sensor is not seen by the game, the game will continue to run the motor until it times out, making the shelf reset multiple times.

  • Page 16: Warranty

    I.C.E. Inc, at the customer’s expense, within 30 days. After 30 days a 15% re-stocking fee will ap- ply to all returns. ICE distributors are independent, privately owned and operated. In their judgment, they may sell parts and/or accessories other than those manufactured by I.C.E. Inc. We cannot be responsible for the quality, suitability or safety of any non-I.C.E.

Table of Contents