Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ice Free Fallin Standart
Summary of Contents for Ice Free Fallin Standart
-
Page 3: Table Of Contents
TABLE OF CONTENTS Safety and Warnings Setup Introduction Game play Features Programming Game Assembly Marquee Install Service Front Plastic Removal Playfield Removal Playfield Array Part Numbers Faults and Errors Assemblies Cabinet assembly Light assembly Ball catch solenoid assembly Ball release solenoid assembly Control Panel assembly 14-15 Air duct assembly... -
Page 4: Safety And Warnings
SAFETY AND WARNINGS BEFORE YOU BEGIN WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED. FAILURE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE A GROUNDED RE- CEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO THE ELECTRONICS. DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME REA- SON AS GIVEN ABOVE. -
Page 5: Game Play
SETUP - INTRODUCTION Game play: The player starts the game by inserting a coin into the coin mech. The ball will begin to circulate throughout the playfield. As the ball falls it is deflected off of the pegs. Once the ball enters the chute, the player must press the “STOP”... -
Page 6: Marquee Install
SETUP - GAME ASSEMBLY Marquee Install Instructions: Position Marquee on top of game as shown below. Be sure and connect the marquee wiring to the AC connector in the game before attaching the marquee hard- ware. Insert one screw with washer into each mounting hole and tighten. The AC connector for the marquee is located inside the access hole. -
Page 7: Service
SERVICE Front Plastic Removal Removal of the front plastic is necessary to gain access to the sensor arrays, LEDs, and playfield displays. Remove the six slotted screws as shown in fig A. Playfield Removal There are three different plastic layers that make up the playfield. -
Page 8: Playfield Array Part Numbers
SERVICE Playfield Sensor array breakdown by parts. You can also refer to the full page wiring diagrams for further information. FR2039TX - OPTO transmitter FR2039RX - OPTO receiver FR203X - LED Light board FR203X - LED Light board WS2032FRX display assembly WS2032FRX display assembly E00414FRX Blue... -
Page 9: Faults And Errors
SERVICE Faults and Errors: To ensure top performance and earnings this game features a power on diagnostics. As power is applied to the game it will display the software revision number on the right display located on the play field. It will also display the required amount of coins to start a game but on the left display. Then the game will check to see if any of the score sensors and ball sensors are faulty This is done first by turning them on. -
Page 34: Marquee Assembly
PARTS LISTINGS Misc. Parts FR3001 Control Panel FR3002 Front Glass FR3024 Ball HH1022 Ticket Bin HH5005 Ticket Dispenser Electrical Parts CG2027 Power cord 9’ 10” CL2364X ASY (Blower) CS8449X ASY (Ballast) DA2001X Main Power Supply DA2002X Transformer for Main power supply E02027G Fan Guard E00211... -
Page 35: Warranty
Warranty I.C.E warrants all components in the Free Fallin’™ game to be free of defects in materials and workmanship for a period listed on the next page from the date of purchase. This warranty does not cover items damaged due to normal wear and tear, subjected to abuse, improperly assembled by the end user, modified, repaired, or operated in a fashion other than that described in the service manual. - Page 36 · Equipment that has failed through normal wear and tear ICE Inc will assume no liability whatsoever for costs associated with labor to replace defective parts or travel time associated therein. All defective warranty covered components will be replaced with new or factory refurbished components equal to OEM specifications.