Advertisement
H. Applications
H-1. Event Memory Functions
Customized
effect
combinations
can
be stored
in
the Event Memory, and later recalled for subsequent
access.
The STORE Button (6) is used to store the
desired effects.
To clean/reset the eight memories.
Press POWER Button (1) to turn off. Then, while holding
down both STORE Button (6) and RECALL Button (7)
press POWER Button (1).
POWER
STORE
۱
4
5
To set a Memory location.
Choose desired effects onthe panel. When the correct
combination is selected, press STORE Button (6), then
press the appropriate EVENT NO. Buttons (8) - (15). The
LED on the EVENT NO. Button (8) - (15) blinks 3 times,
then goes out when memory is completed.
STORE
e
To recall an event setting, press the RECALL Button
and correct the EVENT NO. Button (8) - (15), then press
the AUTO TAKE Button (61).
Note :
Up
to
eight
preset
event
combinations
are
available.
In executing Auto Take successively,
each
memory
operation
will be
performed
in
sequence
according to the numerical
locations
used, ie.
only stored numbers will be "toggled"
through.
So if the No.3 event is skipped in event
memory setting, it will also be skipped when the
AUTO TAKE Button (61) is pressed.
Sop
Caution:
The event memory will disappear in a few days if
the Main Power Switch (98) is kept off.
To exit the Event Memory mode.
Press the RECALL Button (7) again.
H-2. Auto Take
Press the RECALL Button (7).
Instead of the lever controlled
Mix and Wipe using
the Mix/Wipe
Lever (58), automatic
Mix and Wipe
operations can be made using the Auto Take function.
Two kinds of Auto Take are available.
Standard Auto Take
Set up a Wipe Pattern and Digital Effect as desired.
Adjust the TRANSITION Control (60) to the desired auto
take time.
Press the AUTO TAKE Button (61).
Auto-Take
can
be stopped
by pressing
the AUTO
TAKE
Button (61).
The LED's
on both A-bus
and
B-bus buttons blink while Auto-Take is in the stopping
process. Auto-take starts again when the AUTO TAKE
Button (61) is pressed again.
Memory Auto Take
Press the RECALL Button (7).
Select and recall the programmed memory by pressing
the EVENT NO. Buttons (8) - (15).
Press the AUTO TAKE Button (61). The program recalled
from the memory is performed. After this, the next Event
Number is selected automatically.
Press the AUTO
TAKE
Button
(61) again.
program is performed.
The
programs
is in memory
can
be recalled
and
performed one after another by pressing the AUTO
TAKE Button (61) repeatedly.
Auto-Take cannot be stopped on the way in the Event
Memory mode.
Another
H-3. Digital Effects
Many unique Digital Effects are available using this
Digital AV Mixer. By combining specific digital attributes
an experienced user can generate a host of tailored
processes
for specific applications.
Each can
be
stored ina memory location (Event Memory) for instant
recall. Below are a couple of sample combinations.
Auto-Take
Select the same source input for both the A-bus and
B-bus then adjust 2 different digital effect versions
which can then be mixed or wiped over each other as
desired. For example...
To reset the functions to the factory set mode, press
the POWER Button (1) off. Then while holding down
both color-A (49) and B (50) Buttons, press POWER
Button (1).
Press and activate the PAINT Button (28) and STROBE
Button (27) for the A-bus version. The Mix/Wipe Lever
(58) should be turned to A-bus position at this moment.
Turn the Mix/Wipe Lever (58) to the B-bus position.
Press the B-Button (22) on the DIGITAL EFFECT block.
Press the NEGA Button (25).
Adjust the TRANSITION
Control (60) down to "MIN"
position.
Advertisement
