Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Vaxcel Manuals
  4. Outdoor Light
  5. T0598
  6. Assembly and installation instructions

Vaxcel T0598 Assembly And Installation Instructions

Hide thumbs
1
2
3
4
5

Advertisement

Quick Links

Download this manual
ASSEMBLY AND INSTALLATION
T0598
W
W
WARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d'alimentation principale au panneau
central de disjoncteurs avant d'installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical codes,
it is recommended that you consult with a qualified
electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off the
wall switch is not sufficient to prevent an electrical shock.
4. This fixture requires a 120V AC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge,
make sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to
the sensor, be sure the power is switched "off" before
replacing the bulb.
8. Compatible with most LED dimmable bulb.
Maximum Wattage: 60W Incandescent Bulb or 20W LED
Dimmable Bulb
Work Temperature: -4ºF ~ 104ºF
Side Glass Panel
Set Screw
INSTRUCTIONS
Page 1 / 5
Features
1. Energy saving fixture.
2. Use dim-to-full brightness where dim-illumination
is preferred, such as your front entrance. Use
off-to-full brightness where off/on illumination is
preferred, such as your backyard.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included):
Mounting Plate Unit (A)
Mounting Screw (B)
Bolt Nut (D)
Rubber Pad (E)
Max.60W Type A Bulb
(not included)
Wire Connector (C)
Door
Latch
Front Glass Panel (I)
210317

Advertisement

loading

Related Manuals for Vaxcel T0598

Summary of Contents for Vaxcel T0598

  • Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0598 WARNING: Turn off the main power at circuit breaker before installing fixture. AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

  • Page 2: Installation Steps

    Installation Steps Turn off the power at fuse or circuit box. 1. Unscrew the two bolt nuts (D), remove the two rubber pads (E) and the mounting plate unit (A) from the backplate. 2. Attach mounting plate unit (A) to the outlet box by using two mounting screws (B) . Adjust the length of the preinstalled headless screws if necessary.

  • Page 3: Function And Operation

    Function and Operation MODES OF OPERATION Choose a mode by sliding the switch on the back of the sensor. When power is first applied, the light will turn on immediately. Wait for 100 seconds to allow the sensor to warm up. 1.

  • Page 4: Troubleshooting

    NOTE: 1. The sensitivity of the motion sensor will increase as the Where you install your lantern is important: environmental temperature gets cooler. For best performance, Be sure the light is mounted straight on the wall; gently clean the lens with a soft cloth every 1 or 2 months to otherwise, the detection distance may be limited.

  • Page 5: Spare Parts List

    The following parts are available for re-order if damaged or missing. Spare Parts List: Assembly Kit Set Screw 6350MM (1 SET) 5423MM Mounting Plate Unit (A) Mounting Screw (B) Front Glass Panel Side Glass Panel Wire Connector (C) Rubber Pad (D) Rubber Pad (E) Upper Glass Panel 10244CG...