Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0542
W
WARNING: Turn off the main power at circuit breaker before installing fixture.
AVERTISSEMENT: Coupez la source d'alimentation principale au panneau
central de disjoncteurs avant d'installer le luminaire.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Important to Know
1. Read all instructions carefully before installation and operation.
2. If you are not familiar with state and local electrical codes, it is
recommended that you consult with a qualified electrician.
3. Before installation, shut off power at the main fuse or circuit
breaker box. Be aware that simply turning off the wall switch is
not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge, make
sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to the
sensor, be sure the power is switched "off" before replacing the
bulb.
8. Compatible with LED dimmable bulb.
Maximum Wattage: 60W
Dimmable Bulb
Work Temperature: -4°F~104°F
Outlet Box
House Grounding Wire
Wire Connector (C)
Cross Bar Unit (A)
Headless Screw
Green Grounding Screw
Mounting Screw (B)
Fixture Grounding Wire
Fixture Wire
INSTRUCTIONS
Incandescent
Bulb or 20W LED
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or garage
door. Use the dark-to-bright illumination option
where you do not need minimum brightness, such
as the backyard or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included)
Cross Bar Unit (A)
Bolt Nut (D)
Backplate
Glass Shade
Clip x 3
Set Screw x 3
Page 1/4
Mounting Screw (B)
Wire Connector (C)
Rubber Pad (E)
Fixture
Bolt Nut (D)
Rubber Pad (E)
Socket
Bulb T12 4" high or
Type A Max.60W
(not included)
Metal Frame
191205
Advertisement
Related Manuals for Vaxcel T0542
Summary of Contents for Vaxcel T0542
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0542 WARNING: Turn off the main power at circuit breaker before installing fixture. AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
- Page 2 Installation steps Turn off the power at fuse or circuit box. 1. Remove the two bolt nuts (D), the two rubber pads (E) and the cross bar unit (A) from the backplate. 2. Attach the cross bar unit (A) to the outlet box using two mounting screws (B). Adjust the length of the preinstalled headless screws if necessary.
- Page 3 4. 0 MODE (nighttime operation only) ● The light will turn to low level brightness (0%~50% brightness) at dusk. The light will turn to high-level brightness (100% brightness) when motion is detected, and stay on as long as the motion is continuing. When motion is no longer detected, the light will remain on for the predetermined time you set (5~180 seconds), and then revert to low level brightness you set.
- Page 4 ----In Test Mode, the light stays on full brightness after 5 seconds: 1. If during daytime, make sure the slide switch is at the TEST position. 2. Whether the motion is detected at all time. ---In 3H or 6H Mode, the light is still on full brightness,even though it has been 3 hours or 6 hours after dusk, respectively: 1.