Before Using The Appliance For The First Time; Setting The Water Hardness Range; Calibrating The Altitude; Setting The Clock - NEFF B45C44 3AU Series Instruction Manual

Before using the appliance for the first time

Once your new appliance has been connected,
in the temperature display. Before you can use your appliance,
you must make a few settings:
Set the water hardness range
■
Calibrate the altitude
■
Set the clock
■
Clean the appliance before using it for the first time
■
Note: You can correct these settings at any time. For
information about changing the water hardness range and the
altitude difference, see chapter: Changing the basic settings;
and for information about setting the clock, see chapter:
Electronic clock.

Setting the water hardness range

Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
The water hardness "hard" (
the setting if the water is softer.
You can determine the water hardness with the test strips
supplied or ask your water supplier.
Notes
If your water is very hard, we recommend that you use
■
softened water.
If you use only softened water, you can, in this case, set your
■
appliance to the softened water hardness range.
If you use mineral water, then set the water hardness range to
■
hard.
If you use mineral water, then it must be non-carbonated (see
■
chapter: Filling and emptying the water tank).
Use the temperature selector to set the water hardness
1.
range.
Water hardness range
softened
soft
medium
hard
Press and hold the info button for 3 seconds.
±
2.
Your setting is saved.
™†‚
display.

Calibrating the altitude

The altitude difference range "0 - 300 m" (
setting. Change this setting if the location of the appliance is
higher or lower than this.
Use the temperature selector to set the altitude difference
1.
range.
Altitude difference
range
Under 0 m
0 - 300 m
™...„
) is the default setting. Change
™...„
Setting symbol (temperature dis-
play)
™...‹
™...‚
™...ƒ
™...„
appears in the temperature
) is the default
™†‚
Setting symbol (temperature dis-
play)
™†‹
™†‚
appears
Altitude difference
range
300 - 600 m
600 - 900 m
900 - 1200 m
1200 - 1500 m
1500 - 1800 m
1800 - 2100 m
2100 - 2400 m
above 2400 m
Press and hold the
2.
Your setting is saved.

Setting the clock

Note: When you press the
3 seconds to set the clock using the rotary selector. Should this
have been insufficient for you, you can amend the clock time
later.
: flashes in the clock display.
‹ ‹‹
Briefly press the
1.
setting mode.
The and
KJ
clock display.
Set the current time using the rotary selector.
2.
Your setting is accepted after 3 seconds.
Changing the clock
To subsequently change the time, press the
button repeatedly until the
Change the time with the rotary selector.

Cleaning the appliance

Clean your appliance before using it for the first time.
Remove the accessories from the cooking compartment.
1.
Completely remove any residual packaging (e.g. chips of
2.
polystyrene) from the cooking compartment.
Clean the accessories and cooking compartment with hot
3.
soapy water (see section: Cleaning and care).
Fill the water tank with 400 ml water (see section: Filling and
4.
emptying the water tank).
Slide in the water tank all the way.
5.
Switch on the appliance. To do this, press the operating
6.
mode selector so that it pops out.
The appliance is then ready for use.
Using the operating mode selector, set
7.
(see section: Operating the appliance).
Setting symbol (temperature dis-
play)
™†ƒ
™†„
™†...
™††
™†‡
™†ˆ
™†‰
™†Š
info button for 3 seconds.
±
KJ clock function button, you have
KJ clock function button to go to the
symbols light up. :
3 ‚ƒ ‹‹
and symbols light up again.
KJ 3
appears in the
clock function
KJ
% Top/bottom heat
9