Table of Contents
Advertisement
Start the descaling programme.
The descaling programme can only be started once the
cooking compartment has completely cooled down. There must
be no residual heat (
or
œ
If you have cooked using steam immediately before descaling,
you must first switch the appliance off so that the residual water
is pumped out of the evaporator system.
Dissolve the descaling tablets in water to make a descaling
1.
solution.
Note: Follow the manufacturer's instructions for the descaling
tablets.
Switch on the appliance.
2.
Press and hold the
descaling button for 3 seconds.
Í
3.
appears in the temperature display and the
š†™
Î
symbols light up.
Fill the water tank with 400 ml of descaling solution and slide
4.
it in fully. Dispose of the rest of the descaling solution and
rinse with water.
Press the
ƒ
Start button.
5.
The
symbol lights up Descaling starts.
ƒ
Notes
If the water tank has not been filled, a signal sounds and the
■
Descale programme does not start. Fill the water tank with
the descaling solution and slide it in fully.
If a signal sounds and the
■
that the
Start button has not been pressed. Press the
ƒ
Start button.
ƒ
The clock display shows how long the Descale programme
■
has left to run.
1st rinse
A signal sounds and the
Î
Empty the water tank, rinse it out thoroughly and fill it with
1.
400 ml fresh water.
Slide in the water tank all the way.
2.
appears in the temperature display (rinsing 1 =
§ü‚
1st rinse). The
ƒ
start symbol flashes.
Press the
Start button.
ƒ
3.
The
symbol lights up The appliance starts rinsing.
ƒ
After the first rinse has completed, a signal sounds and the
Î
symbol lights up.
2nd rinse
Empty the water tank, rinse it out thoroughly and fill it with
1.
400 ml fresh water.
Slide in the water tank all the way.
2.
appears in the temperature display (rinsing 2 =
§ü ƒ
2nd rinse). The
ƒ
symbol flashes.
Press the
Start button.
ƒ
3.
The
ƒ
symbol lights up The appliance starts rinsing.
After the second rinse is complete, the
the
symbol flashes.
Î
Removing the remaining water
Empty and thoroughly rinse out the water tank.
1.
The
symbol goes out.
Î
Switch off the appliance.
2.
Self-cleaning surface
The back wall of the cooking compartment is coated with self-
cleaning enamel. This coating absorbs and disintegrates
splashes from baking and roasting while the oven is in
operation.
Large splashes only disappear after the oven has been used
several times.
30
) shown in the display.
•
symbol flashes, this indicates
ƒ
symbol lights up.
symbol goes out and
Í
Discolouration on the rear wall does not affect the self-cleaning
function.
Caution!
Damage to surfaces on self-cleaning areas due to applying
oven cleaner.Never clean the self-cleaning surfaces with oven
cleaner.
If oven cleaner accidentally gets onto self-cleaning surfaces,
remove it immediately with a sponge and plenty of water.
Caution!
Damage to surfaces on self-cleaning areas due to the use of
abrasive and acidic cleaning agents and aids.
Do not use cleaning agents containing abrasive substances or
acids.
Do not use abrasive cleaning aids such as steel wool or
and
Í
scourers.
EasyClean®
Your appliance comes with an
make cleaning the cooking compartment easier. An
automatically controlled vaporisation of soapy water loosens
residues and makes it easier to remove them afterwards.
In the case of persistent dirt, you can
allow the soapy water to penetrate for a while before
■
switching on EasyClean
rub detergent onto the dirty surfaces before switching on the
■
cleaning aid
repeat the EasyClean® function once the cooking
■
compartment has cooled
Preparation and switching on
EasyClean® only starts when the cooking compartment is cool.
:
Risk of scalding and surface damage!
Never pour water into the cooking compartment when it is hot.
Water vapour will be created and the enamel may be damaged
because of the change in temperature.
Remove the accessories from the cooking compartment.
1.
Carefully pour 0.4 litres of water (not distilled water) with
2.
some detergent into the base trough of the cooking
compartment (Fig. A).
Close the appliance door.
3.
Switch on
4.
"'†
appears in the temperature display.
If, after EasyClean is switched on,
alternately in the temperature display, the cooking
compartment is not completely cooled.
Wait until the cooking compartment has cooled down and
switch EasyClean® on again.
Once EasyClean® has finished the cooking compartment
light switches on. A signal sounds.
Press the
5.
Cleaning up and switching off
Do not leave the remaining water in the cooking compartment
for a long time (e.g. overnight).
Open the appliance door and remove the remaining water
1.
with an absorbent sponge cloth (Fig. B).
>
EasyClean® function to
EasyClean®.
>
•
KJ
clock function button to exit the clock function.
or
and
appear
œ
"'†
Advertisement
Table of Contents
